Premier Mounts AM100 Manual de usuario
www.premiermounts.com | North America 800.368.9700 | International +1-714-632-7100
2620 Palisades Drive, Corona, CA 92882 USA
INSTALLATION GUIDE
AM100
Low-Prole Ultra-Slim
Swingout Mount for Flat-Panels
9531-100-001-0X v4.0
publ. 03/25/19
Maximum Flat Panel Weight:
100 lb. / 45.5 kg.
Installation Guide
AM100
www.premiermounts.com | North America 800.368.9700 | International +1-714-632-7100
Page 2
INCLUDED COMPONENTS
TOOLS FOR INSTALLATION
5/16” x 3” Lag Bolts
(Qty 4)
Green Level
(Qty 1)
Universal Spacers
(Qty 8)
5/16” Flat Washers
(Qty 4)
Universal Washers
(Qty 4)
Depth Measuring Straw
(Qty 1)
10mm Socket
(Qty 1)
M4 Allen Key
(Qty 1)
M2.5 Allen Key
(Qty 1)
Finned Anchor
(Qty 4)
Pencil Protective Eyewear
Electronic Stud Finder M6 or 1/4” Wood Drill Bit 3/8” Concrete Drill Bit
Portable Drill Hammer
Phillips Head ScrewdriverLeveler Socket Wrench
13mm or 1/2” Socket
Wall Mount
(Qty 1)
Template
(Qty 1)
M8 x 16mm
M6 x 25mm
M6 x 16mm
M8 x 25mm
(Qty 4)
(Qty 4)
(Qty 4)
(Qty 4)
Installation Guide
AM100
www.premiermounts.com | North America 800.368.9700 | International +1-714-632-7100
!
Page 3
CHANGING THE DEFAULT SWINGOUT PIVOT POSITION
M2.5 Allen Key
Left
(default) Mid Right
1
3
4
Loosen the eight flat screws to disengage
the upper and lower chassis.
Put together the mount after
adjusting the swing pivot position
and recap the plastic plugs.
Fully tighten all hardware
before hanging the mount.
2
Loosen the set
screw (top and
bottom)
Plastic
plugs
OPTIONAL:
Installation Guide
AM100
www.premiermounts.com | North America 800.368.9700 | International +1-714-632-7100
1
2
Page 4
Find the center of the wood studs
and mark the wall with a pencil
Position the template to the desired
location.
Drill into 4 marked mounting points
on the wall surface.
Wood Application:
Use 1/4” drill bit
Concrete Application:
Use 3/8” drill bit
FOR CONCRETE APPLICATIONS SEE PAGE 6
TAPE THE TEMPLATE
LEVEL
Stud
Finder
Installation Guide
AM100
www.premiermounts.com | North America 800.368.9700 | International +1-714-632-7100
3
4
Page 5
LOOSEN THE (2) M5 FLAT SCREWS TO
REMOVE THE BRACKET MOUNT PLATE
DETACH THE CABLE ACESS COVERS
TO EXPOSE THE MOUNTING LOCATIONS
Installation Guide
AM100
www.premiermounts.com | North America 800.368.9700 | International +1-714-632-7100
5
Page 6
Wood Application Concrete Application
LEVEL
LEVEL
43
21
(4) 5/16” x 3” Hex Lag
and (4) 5/16” Washers
Finned Anchor (supplied)
for concrete only
Use 3/8” Concrete
Drill Bit
Use 13mm or
1/2” Socket
Wood Studs
Confirm the placement of the mounting screws before bolting into place.
Installation Guide
AM100
www.premiermounts.com | North America 800.368.9700 | International +1-714-632-7100
6
7
Page 7
Small Straw or Toothpick
Marking the 1/8”
Allowance
Small Straw
or Toothpick
Small Straw
or Toothpick Depth Plus 1/8” Allowance
Mark
Depth Plus 1/8” Allowance
Mark
1) Insert a small straw or toothpick into the threaded inserts found on the
back of the at-panel.
2) Use a pencil to mark the depth of the threaded insert on the small straw
or toothpick.
3) Mark the straw or toothpick 1/8” above the depth of the threaded insert,
as shown in Figure 1.
4) Insert the small straw or toothpick into the remaining threaded inserts
to compare and verify their depth using the straw or toothpick’s 1/8”
allowance mark.
5) Locate the correct diameter screw for the threaded insert.
If the screw you selected is longer than the 1/8” allowance mark on
the small straw or toothpick, as shown in Figure 2 and Figure 3, do
not use this screw. The screw length must not bypass the mark.
6) Test each size of the screws provided.
The correct screws should thread easily into themounting point and
not pull out when tension is applied.
Selecting the Mounting Hardware
1
2
FASTEN USING (2) M5 FLAT SCREWS TO
SECURE THE BRACKET MOUNT PLATE
Installation Guide
AM100
www.premiermounts.com | North America 800.368.9700 | International +1-714-632-7100
8
Page 8
M8
M5, M6
M4
x4
INSTALL THE MOUNTING BRACKETS
USE ADDITIONAL UNIVERSAL SPACERS TO FILL UNEVEN GAPS
Longer screws length (commercially available)
might be needed if using spacers.
Directional arrows on
the brackets pointing up
TOP OF
FLAT PANEL
1˝ ¼˝
Selected the mounting
screws (from previous step)
Universal Washers
C/L
C/L
Installation Guide
AM100
www.premiermounts.com | North America 800.368.9700 | International +1-714-632-7100
9
10
Page 9
HOOK THE DISPLAY BRACKETS
TO THE MOUNT
POST-LEVELING
(RETRACTED POSITION)
Post leveling control
adjustment screws.
Tighten these screws to
lock the brackets in place.
Center the display
to the mount
Installation Guide
AM100
www.premiermounts.com | North America 800.368.9700 | International +1-714-632-7100
11
12
Page 10
Use 10mm deep
socket to adjust
the tension
Use 2.5mm hex key
to adjust the tension
near the pivot.
Do not over tighten.
TILT
ADJUSTMENT
ROUTE POWER AND SIGNAL
ALONG THE MOUNT
Otros manuales para AM100
2
Tabla de contenidos
Otros manuales de Rack y soporte de Premier Mounts
Premier Mounts
Premier Mounts ECM-3000 Manual de usuario
Premier Mounts
Premier Mounts PSD-TS Manual de usuario
Premier Mounts
Premier Mounts PBL-200 Manual de usuario
Premier Mounts
Premier Mounts PFC-OMND Manual de usuario
Premier Mounts
Premier Mounts PRC-LA Manual de usuario
Premier Mounts
Premier Mounts PBM-760L Manual de usuario
Premier Mounts
Premier Mounts LMVSP Manual de usuario
Premier Mounts
Premier Mounts CTM-MS1 Manual de usuario
Premier Mounts
Premier Mounts MVW55 Manual de usuario
Premier Mounts
Premier Mounts UMB-DBTS Manual de usuario
Premier Mounts
Premier Mounts AM100 Manual de usuario
Premier Mounts
Premier Mounts PSD-TTS/B Manual de usuario
Premier Mounts
Premier Mounts PRF Manual de usuario
Premier Mounts
Premier Mounts CTM-MS1 Manual de usuario
Premier Mounts
Premier Mounts Nesting Cart Series Manual de usuario
Premier Mounts
Premier Mounts UFA Manual de usuario
Premier Mounts
Premier Mounts PRF Manual de usuario
Premier Mounts
Premier Mounts AST-2446 Manual de usuario
Premier Mounts
Premier Mounts UNI Manual de usuario
Premier Mounts
Premier Mounts TL84-MS2 Manual de usuario
