PR Lighting PR-8129 Manual de usuario

GALAXY

PR-8129

This product manual contains important information about the safe installation and useof this product. Please

read and follow these instructions carefully before installing and using the product and keep this manual in a

safeplaceforfuturereference.

PR LIGHTING LTD.

http://www.pr-lighting.com

INDEX

1. SAFETYANDWARNINGS

2. INSTRUCTIONS

3.APPEARANCE

4.INSTALLATION

5. SETUPANDCONFIGURATION

6.OPERATIONMENU

7. DMXPROTOCOL

8 SIGNSONTHETOUCHSCREEN

9ERRORMESSAGES

10.TECHNICALDATA

11.CIRCUITDIAGRAMANDPCBCONNECTIONS

12.COMPONENTORDERCODES

ACCESSORIES

The followingitems are supplied withtheprojectorandplease check:

Name

Quantity

Unit

Remark

Clamp

SafetyCord

User manual

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to

change without notice. Whilst every care is taken in the preparation of the manual we reserve the right to change

specifications in the course of product improvement. The publishers cannot be held responsible for the accuracy of the

information herein, or any consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit

are in good condition before installation and use. Should there be any damage caused by transportation, consult your

dealer and do not use the unit. Any damage caused by improper use will not be assumed by the manufacturer and / or

dealer.

Note: Forthe products made by GuangzhouPRlightingLtd,thewarranty for the whole product is one year starting fromthedelivery date

butthelightsourceisnotwithinthewarranty.

Any future technical change in the user manual won’t be with any notice.

1. SAFETYANDWARNINGS

NOTE

Before a projector’s installation, power-on, operation and maintenance, please carefully read

thesafety informationhereinafter!

Thefollowingsafetysignsareusedintheusermanual.

Warning

User

Manual

Electrical

shock

Goggles

Protective

Gloves

Flames

High

Temperature

● Whenunpacking , check if there istransportation damage before using the projector. Should there be any

damagecausedbytransportation,consultyourdealeranddonotuseit.

●The manufacture is not responsible for loss caused by the user not following the manual or changing the projector

ashe/shelikes

●Pleasebe notedthatthedamage caused by changingthe projectoratwill isnot warranted.

● Do nothesitate to contact thedealer or the manufacturerif anyquestionsor advice.

● Theprojector isforindoor useonly,IP20.

● Use only in dry locations. Keep this unit away from rain and moisture, excessive heat, humidity and dust. Do not

allowcontactwithwater oranyotherliquids.

●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while

being operated

●The projector is only intended for installation, operation and maintenance by qualified personnel. And the

operationmuststrictlyfollowtheproceduresinthemanual

●Norepairablepartsintheprojector and do not opencoversfor maintenancebyyourself.

●Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned.

●Do notconnectthis device to any typeofdimmerpack

●After lamp switched on, the minimumdistance between theprojectorand illuminated surface is 10m

●lens andotheropticalpartsshallbereplacedimmediatelyiftheyhavedeformedor beendamaged,otherwisethe

lightoutput willbecompromised.

●Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use a

projectorwhilecovers(housing)areoff

●Keepthelampcleananddonottouchitwithbarehands.

●Whileoperatingit, wearprotective items.

●Anyelectricalconnectionmustbecarriedoutbyaqualifiedperson.

●Before installation,pleaseconfirmthevoltage supplied matcheswhatisrequired for the projector

●Eachprojector mustbeproperlyearthedand installedasperrelated electricalstandards.

●Do not use power cord with itsinsulatordamaged and connectthepowercord withother cables.

●If the projector is not used or under cleaning,, please hold the plug and unplugit. Do not unplug it forcefully

or bypullingthepowercable.

●Allpowercords mustconformto relatedsafetyandregulations

●While beingoperated,theprojector shouldnotbeunderrainsor inhumidity.

●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other

electrical parts’ life will be shortened .

●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety

cord suppliedthroughthesafetycord holesforsafetysupport.

●Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from

power mains.

●Afterrunningfor30minutes,thetemperatureofthehousingoftheprojectoris55℃.After stableoperation,

itstemperatureis70℃.

●While the lamp is stricken for the first time, there will be smoke and strange smell. It’s normal and does not

meantheprojector hassomedefects.

●Donotmounttheprojectordirectlyoninflammablesurface.

●Do not project the beam straightly oncombustible items and the minimum distance between the projector

andilluminateditemsis5m.

●Aprojector should be installed with good ventilationand the minimum distance betweenthe projector and

walsis50cm.Atthesametime,pleaseensurethefansandair inletsandoutletsare workable.

2. INSTRUCTIONS

●CLEANINGANDMAINTENANCE

If a projector can’t start. Please check if the fuse is blown up. If it does, replace it with a new fuse with same ratings. And the

projector has over-temperature protective device. If the temperature is too high, the protective device will be triggered to shut the

projector off. When it happens, please check if the fans run normally or fan shield is blocked by dust. After the issue is solved,

restarttheprojector.

The accumulationof oil, smoke and dust on the lens will compromise thelight output. Cleaning a projector is very necessary to

ensure areliable use ofit. Cooling fans need to be cleaned every 15days.Internal lens, reflector and hot mirrorneed to be cleaned

periodicallytooptimizelightoutput.

Cleaning frequencyis to be decided by operations and its environment. Use soft cloth and normal detergent for glass forcleaning

work. It’s advised external optical system be cleaned every 20days and internal optical systems every 30/60days. Keep lens clean

and do not touchopticalpartswithbare hands.

●Beforeany maintenanceandcleaning,please ensuretheprojectisoffthepower

●Onlyqualified personisallowedtodomaintenance

●Duringmaintenance and beforemaintenance,theprojector mustbeoff power.

●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via

frontlenswhetheritrunsornot

●Do not use alcoholor otherorganic solvent tocleanthe housing toavoid damage.

●Donotuseanysolventwithchemicalelementsto clean color filtersorhotmirror.

●TROUBLESHOOTING

PROBLEM

ACTION

The projector doesn’t switch on

Checkthepower cordconnection

Power Switch fails or is not connected well, call a professional

technicianforrepairingandchecking

Control board is not connected normally, call a professional technician

forrepairingandchecking,

Theprojectcanbe turned on, butthe LEDlamps

can’t be on

LED lamp board is not connected well, calla professional technician for

repairing and checking

TheLEDlamps canbeon,butnotcontrolled

byDMX

CheckDMXStartAddress

CheckifXLRcablefailsornot

Thebrightnessdecreasesobviously

Ambient temperature is too hot which makes the projector too hot,

pleasetake appropriateventilationmeasures

3. APPEARANCE

4. INSTALLATION

●RIGGING

While transportation of the fixture, please lock both Pan and Tilt well; Before the use of the fixture, please unlock both. It’s forbidden

to run the fixture while it’s locked.

Take 2clamp and 1 the safety cord out from the package and mount 1 clamp on the BOTTOM of fixture with 2 retainers attached to

theclamp.Hang the fixtureonthesteeltrussandfastentheretainersattached totheclamp. Always ensurethat the locationthatyouare

going tomounttheunit is secureandisstrongenoughtosupporttheweightoftheunit(SeetheWARNINGasshown above) Topass

SAFETY CORD through the SAFETYHOLE on the back cover of the base of the fixture for safety! Always ensure that the

unitisfirmly anchoredtoavoidvibrationand slipping whilstfunctioning.

WARNING:

●Theprojector MUSTbelifted orcarriedbytheHANDLESinsteadofclamps.

●.For safety the safety cord should afford 10 times the Projector’s weight.

●POWERCONNECTION

Connectthepower cordasfollows:

L(live)=brown

E(earth) =yellow/green

N(neutral)=blue

Before power connection, please ensure the power supplied mustmatch what the nameplate says. It is recommended that each

projectorbe connected withpowerseparatelyso that theymay be individuallyswitchedonandoff.

Note: If projectors are connected in series, please connect POWERIN port of the 1st projector with the Power Mains, then

connectitsPOWEROUTwithPOWERINof the 2nd projector,and soontillallfixturesare connected.Ifthevoltagesupplied

is 200V-240V, the maximum projectors connected is 8pcs, if it is 100V-120V, the maximum is 4pcs. The diameter of the cores

ofthe wiresforthePowerin/outcablesmustbeequalor biggerthan2.5mm2.

●The earth wire(yellow/green) must be connected to the ground. And electrical connection must be in

accordancewiththestandardsconcerned.

●Ifanyquestionsaboutthe electricalinstallation,donot continuebutconsulta qualifiedelectrician.

●DMXCONTROLCONNECTION

Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with

each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon5 pin (which are included with the

projector)or5pinXLRplugsandsockets.TheXLR'sareconnected asshowninthefigureabove.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets

mustn’t be connected in any way other than mentioned in the above figure. The projector accepts digital control signals in protocol

DMX512(1990).

Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second

fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX

terminator asshowninthefigurebelow.

●DMXTERMINATOR

In the Controller mode, at the last projector in the chain, the DMX output has to be connected witha DMX terminator. This prevents

electrical noisefromdisturbingandcorruptingtheDMXcontrol signals.

The DMX terminator is simply an XLR connector with a 120(ohm) resistor connected across pins 2 and 3, which is then plugged

intotheoutput socket onthelastprojector inthechain.Theconnectionsare illustratedbelow.

5. SETUPANDCONFIGURATION

●FRONTPANELOPERATION

Projectorconfigurationcanbesetconvenientlyviapushbuttonandthetouchscreen.

Launchtheprojector andpressbutton ENTER formore than3secondsto unlockthepanel, thedisplay willshowthe functionmenu of

the projector, each main menu has its submenus and each submenu has a specific function. For details, please see the

“OPERATION MENU” section.

Pressbutton UP or DOWN ifyouwanttobrowsethroughthevariousSetupOptions.

Pressbutton ENTER tosave yoursettingsorenterthesubmenu.

Pressbutton UP or DOWN tochangevalues(plusorminus)

Pressbutton FUNC, itwillreturntotheuppermenu.Ifbutton FUNC notpressed,thedefault willshow displaystatusautomatically.

●DMXSTARTADDRESS

If many projector s are controlled by the controller, each projector should be set with a start address to receive signals sent by the

controller and respond to it. The projector have 3 DMX modes. There are short mode, standard mode and extended mode. For

example standard mode has 30channels, so set the No. 1 Projector ’s address 001, No. 2 Projector ’s address 031, No. 3 Projector ’s

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain. PIN 3

PIN 2

FUNC

DOWN

ENTER

address061 and soon.

Launchtheprojector. Pressbutton ENTER morethan2secondstounlockpanel.

Pressbutton ENTER todisplayDMXaddress;

Pressbutton UP and DOWN,youcanset the address;

Pressbutton ENTER toconfirm;afterpowered on next time,thedefault willbelastvaluesaved

Pressbutton FUNC, itwillreturntotheuppermenu

●DMXWIRELESSCONTROL(Optional)

Theprojector hastheoptionalwirelesscontrol function.With wirelessreceiver moduleandantenna,itcanachieveremotecontrol.

Thesetupofitisbelow:

1. Enter into the projector’s menu. Select the menu “Config Settigns” via the bottoms of UP and DOWN

2. Select DMX control Mode---- Wireless First (Note: do not select XLR ONLY),then wireless indication in the

front panel willbe on, meaningwireless control functionis activated.

Only after the projector is linked with a transmitter, can it receive wireless signal sent by the transmitter. If unlinking it,

Press “Enter” for the menu of Unlink Wireless under the upper level menu of Config Settigns .

●STAND-ALONEMODE

Operate the projector without connecting with a controller, enable the master mode through the operation panel, the

projector will run in Stand-Alone mode automatically.

DMX address can be set at any number within 512.

●MASTER/SLAVEMODE

Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,

connect the first projector ’s DMX output to the second projector ’s DMX input using XLR-XLR control cable and then connect the

secondprojector’s DMX output to the third projector ’s DMX input, and so on until all projector are connected in this way. Eventually

connectthelastprojector ’s DMX output to a DMXterminator. Set 1st projector as the master and others are Slaves.

Start Addresses of all Slaves are 001; Operation mode of the Master can be set any mode for a Master’ and Slaves’ operation mode can

be setaccordingly.

AfterPoweredon,thegroup willruninMaster/SlaveMode

6. OPERATIONMENU

1stLEVEL

2ndLEVEL

3rdLEVEL

4thLEVEL

5thLEVEL

Address

DMX Address

1-486（Short mode）

1-482（Standardmode）

1-410（Extended ）

IP Address

Default IPAddress

2.X.X.X/10.X.X.X

CustomIPAddress

X.X.X.X

SubNetMask

X.X.X.X

ArtNetUniverse

0-255

Reset

Total Reset

ReallyReset?

Confirm/Cancle

Pan&TiltReset

ReallyReset?

Confirm/Cancle

ColourSystemReset

ReallyReset?

Confirm/Cancle

ConfigSettings

DMXChannelMode

ShortMode

StandardMode

ExtendedMode

ViewSelectedMode

Strobe

………..

Signal Select

XLROnly

XLRFirst

WirelessOnly

WirelessFirst

WirelessIn/XLROut

ArtNetOnly

ArtNetIn/XLROut

LossofDMX

Normaltimeout

Hold LastValue

DisplayConfig

DisplayMode

OffAfterDelay

OnAlways

DisplayInvert

InvertOFF

InvertON

InvertAuto

LanguageSetting

English

Chinese

TemperatureUnit

CelsiusDegree

FahrenheitDegree

Un-LinkWireless

ReallyUn-Link?

Confirm/Cancle

Defaults

RestoreDefaults?

Confirm/Cancle

Option Settings

Pan/TiltSettings

PanDMXInvert

OFF/ ON

TiltDMXInvert

OFF/ ON

PanTilt Swap

OFF/ ON

XYFeedback

OFF/ ON

Pan/TiltMode

speed/Time

InvertSettings

LensInvert

OFF/ ON

FocusInvert

OFF/ ON

DimmerSettings

Gamma Curve

Gamma 2.0/2.2/2.4/2.6

LEDRefreshRate

0/15000/20000/25000Hz

DimmerSpeed

Fast/Medium/SlowSpeed

FanSettings

Standard/Theatre

Defaults

RestoreDefaults?

Confirm/Cancle

Information

ViewDMXValues

LampHours

Reset Lamp Hours

Total Hours

Temperature

DisplayBoardXX℃/F

PanTiltBoardXX℃/F

Driver Board XX℃/F

LEDBoard1XX℃/F

LEDBoard2XX℃/F

LEDBoard3XX℃/F

LEDBoard4XX℃/F

LEDBoard5XX℃/F

LEDBoard6XX℃/F

LEDBoard7XX℃/F

SoftwareVersion

DisplayBoard

System=XXX

Boot =XXX

PanBoard

System=XXX

Boot =XXX

Driver Board

System=XXX

Boot =XXX

LEDBoard1

System=XXX

Boot =XXX

LEDBoard2

System=XXX

Boot =XXX

LEDBoard3

System=XXX

Boot =XXX

LEDBoard4

System=XXX

Boot =XXX

LEDBoard5

System=XXX

Boot =XXX

LEDBoard6

System=XXX

Boot =XXX

LEDBoard7

System=XXX

Boot =XXX

ElectronicSN

ElectronicSN=

************

RDMDeviceLabel

ANSIE1.20RDM

VersionX.X

FanStatus

HeadFan

Service

ManualEffectControl

StrobeXXX

DimmerXXX

…

FactoryTest

…

Operation

Mode

DMXMode

ChangeOperationMode?

Confirm/Cancle

MasterMode

PresetMemory

ChangeOperationMode?

Confirm/Cancle

UserMemory 1

ChangeOperationMode?

UserMemory 2

ChangeOperationMode?

Tabla de contenidos

Otros manuales de Equipo de DJ de PR Lighting

PR Lighting

PR Lighting XR-230 BEAM Manual de usuario

PR Lighting

PR Lighting PR-8330 Manual de usuario

PR Lighting

PR Lighting PR-8802 Manual de usuario

PR Lighting

PR Lighting OMEGA Manual de usuario

PR Lighting

PR Lighting XR 380 Beam Manual de usuario

PR Lighting

PR Lighting MEGA COLOUR 2000 Manual de usuario

PR Lighting

PR Lighting XPar 150 Manual de usuario

PR Lighting

PR Lighting XR 1700 FRAMING Manual de usuario

PR Lighting

PR Lighting StarBrite Manual de usuario

PR Lighting

PR Lighting XR440 BEAM Manual de usuario

PR Lighting

PR Lighting XLED 300 Beam Manual de usuario

PR Lighting

PR Lighting CSL 1037 Manual de usuario

PR Lighting

PR Lighting JNR BWS 350 Manual de usuario

PR Lighting

PR Lighting XR 1000 Framing Manual de usuario

PR Lighting

PR Lighting AQUA 580 BEAM Manual de usuario

PR Lighting

PR Lighting JUNIOR JNR-8146C Manual de usuario

PR Lighting

PR Lighting XPar 348 Manual de usuario

PR Lighting

PR Lighting PILOT 300 Manual de usuario

PR Lighting

PR Lighting Theatre Master PR-3010 Manual de usuario

PR Lighting

PR Lighting LED Studio 3201D Manual de usuario

PR Lighting

PR Lighting AQUA LED 730 FRAMING Manual de usuario

PR Lighting

PR Lighting AQUA LED 600 SPOT Manual de usuario

PR Lighting

PR Lighting XPar 1012 Manual de usuario

PR Lighting

PR Lighting PR-8242 Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario