Power Fist 8656860 Manual de usuario

V4.0 8656860

Please read and understand all instructions before use. Retain this manual for

future reference.

User Manual

8in.VariableSpeed

BenchMountBuffer

8656860 8 in. Variable Speed Bench Mount Buffer V4.0

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Wheel Size 8 in.

Arbor Size 5/8 in.

No Load Speed 2,000 to 3,450 RPM

Voltage Rating 120V

Current Rating 7A

Frequency Rating 60Hz

INTRODUCTION

The 8 in. Variable Speed Bench Mount Buffer is great for polishing, buffing and

the smoothing of metal and other materials. It has a 3/4 HP motor, sealed ball

bearings for smooth and quiet operation and precision machined shafts. The

cast iron base comes predrilled to attach to a bench or pedestal.

SAFETY

WARNING! Read and understand all instructions before using this tool. The

operator must follow basic precautions to reduce the risk of personal injury

and/or damage to the equipment.

Keep this manual for safety warnings, precautions, operating or inspection and

maintenance instructions.

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A notice

is an alert that there is a possibility of property damage, injury or death if certain

instructions are not followed.

8in.VariableSpeed

BenchMountBuffer

V4.0 8 in. Variable Speed Bench Mount Buffer 8656860

Visit www.princessauto.com for more information 3

DANGER! This notice indicates an immediate and specific hazard that will

result in severe personal injury or death if the proper precautions

are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that

could result in severe personal injury or death if the proper

precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that may result

in minor or moderate injury if proper practices are not taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice will

result in equipment or property damage, but not personal injury.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well-lit

and free of distractions.

2. Keep anyone not wearing the appropriate safety equipment away from the

work area.

3. Store unused tools properly in a safe and dry location to prevent rust or

damage. Lock tools away and keep out of the reach of children.

4. Do not install or use in the presence of flammable gases, dust or liquids.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the Canadian

Standards Association (CSA) or American National Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side protection

for the eyes. Eye protection equipment should comply with CSA Z94.3-07

or ANSI Z87.1 standards based on the type of work performed.

2. Wear the appropriate type of full-face shield in addition to safety googles,

as the work can create chips, abrasive or particulate matter.

3. Wear gloves that provide protection based on the work materials or to

reduce the effects of tool vibration.

a. Do not wear gloves when operating a tool that can snag the material

and pull the hand into the tool.

8656860 8 in. Variable Speed Bench Mount Buffer V4.0

4 For technical questions call 1-800-665-8685

4. Wear protective clothing designed for the work environment and tool.

5. Non-skid footwear is recommended to maintain footing and balance in the

work environment.

6. Wear steel toe footwear or steel toe caps to prevent a foot injury from

falling objects.

7. Wear the appropriate rated dust mask or respirator.

8. This tool can cause hearing damage. Wear hearing protection gear with an

appropriate Noise Reduction Rating to withstand the decibel levels.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to tool.

1. Do not operate any tool when tired or under the influence of drugs, alcohol

or medications.

2. Avoid wearing clothes or jewelry that can become entangled with the

moving parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating a tool. Proper footing and balance

enables better control in unexpected situations.

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained from

repeated use) replace strict adherence to the tool safety rules. If you use

this tool unsafely or incorrectly, you can suffer serious personal injury.

1. Use the correct tool for the job. This tool was designed for a

specific function. Do not modify or alter this tool or use it for

an unintended purpose.

2. Keep hands and fingers away from the buffing area. Any part of body

coming in contact with moving parts could cause an injury.

3. Never use a tool with a damaged buffing wheel. Change the buffing wheel.

Use only flanges supplied with the buffer.

4. Before using the tool on a workpiece, test the tool by running it at the highest

no-load speed for at least 60 seconds in a safe position. Stop immediately if

there is any abnormal vibration or wobbling that could indicate poor

installation of the buffing wheel. Check the tool to determine the cause.

V4.0 8 in. Variable Speed Bench Mount Buffer 8656860

Visit www.princessauto.com for more information 5

5. Do not start the tool when the buffing wheel is touching the workpiece.

6. Do not allow the tool’s motor to overload and/or overheat by taking

work breaks.

7. This tool will not stop moving immediately. Do not leave the tool

unattended until it has come to a complete stop.

8. Clean dust and debris from beneath the buffing wheels frequently.

9. Do not stand directly in front of the machine when turning it ON. Always

stand off to the side of the machine and do not allow any part of your body

to be in line with the wheel’s path.

10. Make sure the bench mount buffer is on a firm, level surface and properly secured

to avoid injury from unexpected movement. Firmly clamp or bolt the bench mount

buffer to a support surface to prevent slipping or sliding during the operation.

11. Do not use a buffing wheel that vibrates when used. Replace the wheel if it

cannot be balanced. Also inspect the machine for other causes of vibration

such as worn bearings or a bent shaft. Repair or replace broken

components immediately before reusing the machine.

12. Only use a buffing wheel of the recommended size with the correct

arbor size and shape that matches the buffer’s spindle.

KICKBACK PRECAUTIONS

Kickback is a sudden reaction to a pinched or snagged cutting accessory caught

on the material. The material can be ejected and inflict a serious injury on the

user or a bystander. Kickback can also damage the tool or workpiece.

Kickback can be avoided by taking proper precautions:

1. Maintain a firm grip on the material and position your body and arms to

allow you to resist a kickback. Kickback can propel the material in the

direction of the grinding accessory’s rotation.

2. Use special care when working on corners, sharp edges or flexible material.

These workpieces have a tendency to snag the grinding accessory.

3. Only use buffing accessories designed for the tool.

POWER TOOL PRECAUTIONS

1. Do not allow the tool to run without load for an extended period of time, as

this will shorten its life.

8656860 8 in. Variable Speed Bench Mount Buffer V4.0

6 For technical questions call 1-800-665-8685

2. Do not cover the air vents. Proper cooling of the motor is necessary to

ensure normal life of the tool.

3. Avoid unintentional starting. Ensure the switch is off when connecting to

the power source.

4. Disconnect the power source before installing or servicing the tool.

5. After making adjustments, make sure that any adjustment devices are

securely tightened.

6. Remove adjusting keys and wrenches before turning the tool on. A wrench

or a key that is left attached to a rotating part of the tool increases the risk

of personal injury.

7. Never force the tool. Excessive pressure could break the tool, resulting in

damage to your workpiece or serious personal injury. If your tool runs

smoothly under no load, but does not run smoothly under load, then

excessive pressure is being used.

8. Do not touch an operating motor. Motors can operate at high temperatures

and can cause a burn injury.

9. Only use an accessory that exceeds the No Load Speed rating (see

Specifications).

ELECTRICAL SAFETY

WARNING! To reduce risk of electric shock, be certain that the plug is

connected to a properly grounded receptacle.

1. Disconnect tool from power source before cleaning, servicing, changing

parts/accessories or when not in use.

2. Protect yourself against electric shocks when working on electrical

equipment. Avoid body contact with grounded surfaces. There is an

increased chance of electrical shock if your body is grounded.

3. Do not expose tool to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

4. Do not disconnect the power cord in place of using the ON/OFF switch on the

tool. This will prevent an accidental startup when the power cord is plugged into

the power supply.

V4.0 8 in. Variable Speed Bench Mount Buffer 8656860

Visit www.princessauto.com for more information 7

a. In the event of a power failure, turn off the machine as soon as the

power is interrupted. The possibility of accidental injury could occur if

the power returns and the unit is not switched off.

5. Do not alter any parts of the tool or accessories. All parts and

accessories are designed with built-in safety features that may be

compromised if altered.

6. Make certain the power source conforms to requirements of your

equipment (see Specifications).

7. When wiring an electrically driven device, follow all electrical and safety

codes, as well as the most recent Canadian Electrical Code (CE) and

Canadian Centre for Occupational Health and Safety (CCOHS).

8 Grounded tools must be plugged into an outlet that is properly installed

and grounded in accordance with all codes and ordinances. Check with

a qualified electrician if you are in doubt as to whether the outlet is

properly grounded. If the tool should electronically malfunction or break

down, grounding provides a low resistance path to carry electricity away

from the user.

a. Never remove the grounding prong or modify the plug in any way, as

this will render the tool unsafe.

b. Do not use any adapter plugs.

9. DO NOT use this device with a 2-prong wall receptacle.

a. Choose an available 3-prong power outlet.

b. Replace 2 prong outlet with a grounded 3-prong receptacle, installed

in accordance with the CE Code and local codes and ordinances.

WARNING! All wiring should be performed by a qualified electrician.

8656860 8 in. Variable Speed Bench Mount Buffer V4.0

8 For technical questions call 1-800-665-8685

POWER CORD

1. Insert the power cord plug directly to the power supply whenever possible.

Use extension cords or surge protectors only when the tool's power cord

cannot reach a power supply from the work area.

a. Use in conjunction with a Ground Fault Circuit Interrupter (GFCI). If

operating a power tool in a damp location is unavoidable, the use of a

GFCI reduces the risk of electric shock. It is recommended that the

GFCI should have a rated residual current of 30 mA or less.

2. Do not operate this tool if the power cord is frayed or damaged as an electric

shock or surge may occur, resulting in personal injury or property damage.

a. Inspect the tool's power cord for cracks, fraying or other faults in the

insulation or plug before each use.

b. Discontinue use if a power cord feels more than comfortably warm

while operating the tool.

c. Have the power cord replaced by a qualified service technician.

3. Keep all connections dry and off the ground to reduce the risk of electric

shock. Do not touch plug with wet hands.

4. Prevent damage to the power cord by observing the following:

a. Do not pull on the cord to disconnect the plug from an outlet.

b. Keep cord away from heat, oil, sharp edges or moving parts.

c. Place the electrical cord in a position that prevents it from coming into

contact with the tool and from getting caught by the workpiece. The

cord should always stay behind the tool.

5. Do not allow people, mobile equipment or vehicles to pass over

unprotected power cords.

a. Position power cords away from traffic areas.

b. Place cords in reinforced conduits.

c. Place planks on either side of the power cord to create a

protective trench.

V4.0 8 in. Variable Speed Bench Mount Buffer 8656860

Visit www.princessauto.com for more information 9

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace the

missing part before operating. Failure to do so could result in a malfunction

and personal injury.

Remove the parts and accessories from the packaging and inspect for damage.

Make sure that all items in the parts list are included.

Contents:

• Bench Mount Buffer • 5/8 in.-11 Hex Nuts, 2 pc • Wheel Flange, 4 pc

• Spacer, 2 pc • Sewn Wheel • Soft Wheel

ASSEMBLY & INSTALLATION

Numbered references in parenthesis (#1) refer to the included Parts List.

The buffer comes completely assembled with hex nuts (#1), wheel flanges (#2)

and spacers (#3) packed separately. One spiral sewn wheel and one soft wheel

are included.

INSTALL BUFFING WHEELS

Install the left, then the right buffing wheel onto the bench top buffer.

1. Remove the plastic protective sleeve from the left armature shaft.

2. Slide a spacer (#3) onto the left armature shaft.

3. Slide an inner wheel flange (#2) onto the armature shaft with the flat side

towards the buffing wheel.

4. Slide a buffing wheel on to the armature shaft and butt it against the inner

wheel flange.

5. Slide in the outer wheel flange (#2) and butt the flat side of the flange

against the buffing wheel.

6. Tighten the left-hand threaded hex nut (#1) on to the armature shaft. Make

sure the buffing wheel is firmly held in place and the hex nut is snug against

the outer wheel flange. Use additional spacers (not supplied) if required.

7. Repeat steps 1 to 6 to install a buffing wheel on the other side of the buffer.

Use the right-hand threaded hex nut (#21) for step 6.

8656860 8 in. Variable Speed Bench Mount Buffer V4.0

10 For technical questions call 1-800-665-8685

MOUNT BUFFER

PEDESTAL MOUNT

1. Align the mounting holes in the buffer with the pedestal holes.

2. Drop a 1/4-20 x 1-1/4 in. bolt into each mounting hole.

3. Slide a 1/4 in. washer onto one bolt from beneath the pedestal plate.

4. Place a 1/4-20 in. hex nut on the same bolt and tighten until there is only

1/8 in. space between the buffer base and the pedestal plate.

5. Repeat for the other three bolts.

6. Add another hex nut to each bolt and tighten to prevent them from

loosening due to vibration.

BENCH MOUNT

1. Position the buffer on the bench and mark each hole of the base on

the bench.

2. Predrill a hole for each wood screw if necessary.

3. Place a flat washer over a 1/4 x 1-1/4 in. wood screw.

4. Insert a wood screw and washer through the holes in the base.

5. Tighten the screws until the space between the buffer and bench is 1/8 in.

OPERATION

ON/OFF SWITCH WITH KEY

The ON/OFF rocker switch with key (#16) is located on the front of the buffer. Press

the switch up to turn the power ON. Push the switch down to turn the power OFF.

Remove the yellow key from the switch when you are finished working with the

buffer. The power switch will not work without the yellow safety key in place. The

safety key can only be removed when the power switch is in the OFF position.

BASIC BUFFER OPERATIONS

1. Keep a steady, moderate pressure on the work and keep it moving at an

even pace for smooth buffing.

2. Pressing too hard overheats the motor and prematurely wears down the

buffing wheels.

Tabla de contenidos

Idiomas:

Otros manuales de Herramientas eléctricas de Power Fist

Power Fist

Power Fist 8835548 Manual de usuario

Power Fist

Power Fist 8343055 Manual de usuario

Power Fist

Power Fist 8383853 Manual de usuario

Power Fist

Power Fist 8667834 Manual de usuario

Power Fist

Power Fist 8095903 Manual de usuario

Power Fist

Power Fist 8536591 Manual de usuario

Power Fist

Power Fist 8257370 Manual de usuario

Power Fist

Power Fist 79 pc Manual de usuario

Power Fist

Power Fist 8644171 Manual de usuario

Power Fist

Power Fist Electric Chain Saw Sharpener Manual de usuario

Power Fist

Power Fist 8651598 Manual de usuario

Power Fist

Power Fist 8639106 Manual de usuario

Power Fist

Power Fist 8067936 Manual de usuario

Power Fist

Power Fist 9027814 Manual de usuario

Power Fist

Power Fist 8083115 Manual de usuario

Power Fist

Power Fist 8873127 Manual de usuario

Power Fist

Power Fist 8336232 Manual de usuario

Power Fist

Power Fist 8105942 Manual de usuario

Power Fist

Power Fist 12V Bar Mount Manual de usuario

Power Fist

Power Fist 8757783 Manual de usuario

Power Fist

Power Fist 2990177 Manual de usuario

Power Fist

Power Fist 8604597 Manual de usuario

Power Fist

Power Fist 16-Speed Floor Mount Drill Press Manual de usuario

Power Fist

Power Fist 3462108 Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual