POSIFLEX MT-5208A Manual de usuario
1
MT-5208A/R
MT-5210A/R
Package Contents
MT-5208A/R or MT-5210A/R (x 1)
Pistol grip (x1)
15W power adaptor (x 1)
Stylus (x 1)
RB-3000 Battery pack for pistol grip (x 1)
User manual (x 1)
Barcode scanner user manual (x 1)
MT-5208A/H
MT-5210A/H
Package Contents
MT-5208A/H or MT-5210A/H (x 1)
15W power adaptor (x 1)
Stylus (x 1)
User manual (x 1)
MT-5208A/5210A
Mobile Terminal System
User Manual
12580903020 Ver. B0
http://www.posiflex.com
MT-5208A/5210A is
required to be charged
over 8 hours when
used for the first time.
2
SOME IMPORTANT NOTES
FCC NOTES
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CE CLASS A WARNING
This equipment is compliant with Class A of CISPR 32. In a residential
environment this equipment may cause radio interference.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any
person other than the authorized technicians. The user should consult his/her
dealer for the problem happening. Warranty voids if the user does not follow
the instructions in application of this merchandise. The manufacturer is by no
means responsible for any damage or hazard caused by improper application.
警告使用者
此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，
在此種情況下，使用者會被要求採取某些適當的對策。
SAFETY INSTRUCTIONS
This equipment is not suitable for use in locations where children are likely to
be present.
CONSIGNES DE SÉCURITÉ
3
Cet équipement ne convient pas à une utilisation dans des lieux pouvant
accueillir des enfants.
BATTERY CAUTION NOTES
Dispose of used batteries according to the instructions.
Replacement of a battery with an incorrect type that can defeat a
safeguard (for example, in the case of some lithium battery types)
Disposal of a battery into fire or a hot oven, or mechanically crushing
or cutting of a battery that can result in an explosion.
Leaving a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of flammable
liquid or gas.
A battery subjected to extremely low air pressure that may result in an
explosion or the leakage of flammable liquid or gas.
BATTERIE ATTENTION NOTES
Jetez les piles usagées conformément aux instructions.
Remplacement d'une batterie avec un type incorrect qui peut annuler
une sauvegarde (par exemple, dans le cas de certains types de batterie
au lithium)
Mise au rebut d'une batterie dans le feu ou dans un four chaud, ou
écrasement ou coupure mécanique d'une batterie pouvant entraîner une
explosion.
Laisser une batterie dans un environnement environnant à des
températures extrêmement élevées pouvant entraîner une explosion ou
la fuite de liquide ou de gaz inflammable.
Une batterie soumise à une pression atmosphérique extrêmement basse
pouvant provoquer une explosion ou une fuite de liquide ou de gaz
inflammable.
警告
本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理用過之
電池。
4
Product Feature
Ergonomic Design
Pistol grip shape handle is ergonomically designed for easy handling of the
tablet.
Extra Protection
Hand strap strengthens the stability and eases user’s fatigue during the hours of
work.
All-in-one Solution
Optional dock station equips with a built-in 3” thermal printer and various I/O
connectivity; once the tablet is integrated with the dock station, an all-in-one
POS is instantly at your disposal.
Versatile Function
MSR attachment and 1D or 2D barcode scanner built in the pistol grip; MT-
5208A/5210A offers more than just mobility but versatility.
Long Hour Operation
MT-5208A/5210A is designed with advanced power saving technology that
provides long battery life for daily operation. The pistol grip also houses a
removable battery that can vastly extend the overall operating time.
Views of MT-5208A/H
Front View
Rear View
LED Indicator
Rear Camera
Speaker
Hand strap
3-track Magnetic Stripe
Reader (Optional)
Projected Capacitive
Touch Screen
3-track Magnetic Stripe
Reader (Optional)
5
Left Side View
Bottom Side View
Top View
Micro USB Port
Power Button
Micro SD Card Slot
Mic-in/Line-Out
Combo Jack
Docking Station Connector
5VDC-IN Power Jack
Connecting Hole for Docking Station
6
Views of MT-5210A/H
Front View
Rear View
Bottom Side View
Micro USB Port
LED Indicator
Mic-in/Line-Out
Combo Jack
Rear Camera
Speaker
Hand strap
Expansion Slot for
Optional Attachment
Docking Station Connector
5VDC-IN Power Jack
Connecting Hole for Docking Station
Projected Capacitive
Touch Screen
Rubber Cushion
Rubber Cushion
7
Left Side View
Load RB-3000 Battery Pack and a stylus into
Pistol Grip PG-201E (for MT-5208A/R & MT-5210A/R)
Both MT-5208A/R and MT-5210A/R with PG-201E pistol grip support 1D
CCD, 1D Laser, and 2D barcode scanner. Before the scanner can be initiated,
it is required to install the battery pack RB-3000 and a stylus in the battery
compartment inside the pistol grip. Please follow the steps listed below to
finish the installation.
1. Press down the lever and then push up the cover for battery compartment
as shown in the figure.
2. To replace the existing battery, gently push
the metal clip outwards to release the
battery. If you are installing the battery for
the first time, please skip to the next step.
Metal clip
Power Button
Micro SD Card Slot
Smart Card Reader
(Optional)
8
3. After having the rail on the battery pack
aligned with battery clip, push down the
battery pack into battery compartment.
4. Push down the cover to close the battery
compartment.
Connecting the Pistol Grip onto MT-5208A/R & MT-
5210A/R
MT-5208A/R and MT-5210A/R models are equipped with an additional pistol
grip which aims to help users grip the terminal more easily while they are
operating the scanner. Please refer to the following instructions to install the
pistol grip onto the tablet.
1. To attach the pistol grip to the tablet, align the arrow head on the top
side of the pistol grip with the tail of the arrow on the rear of the
tablet.
2. After ensuring the pistol grip is well
attached to the tablet, push the pistol
grip in the direction indicated by the
arrow as shown in the figure.
9
3. Make sure the head of the down arrow on the pistol grip is supposed to
be aligned with the head of the arrow on the rear side of the tablet as
the below figure shows, which indicates the pistol grip is well
mounted.
4. To check how much battery capacity
remains in PG-201E pistol grip, press
the battery capacity checking button on
the pistol grip to show the current
battery capacity level through the LED
indicator.
Replacing the Pistol Grip with a Hand Strap Cover (Optional)
The hand strap cover is an optional peripheral designed for users to easily hold
the tablet for operation. To replace the pistol grip with a hand strap cover,
follow the steps listed below.
1. While pushing the release lever to the left
(1), slide the pistol grip in the direction
indicated by the arrow in the figure (2).
2. Pull the pistol grip off from the tablet.
1
1
2
2
10
3. Align the hand strap cover with the grooves
on the rear side of the table.
4. Make sure that the hand strap cover is well
attached to the rear side of the tablet.
5. Slide the hand strap cover up in the
direction indicated by the arrow until it is
clicked into place.
6. Fasten the hand strap cover onto the tablet
using a screw.
Replacing the Hand Strap Cover with a Pistol Grip (Optional)
Please follow the below steps to replace the hand strap cover with a pistol grip.
1. Loosen the screw to remove the hand strap
cover from the tablet.
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Terminal táctil de POSIFLEX
POSIFLEX
POSIFLEX XT-3915 Manual de usuario
POSIFLEX
POSIFLEX XP-3000 Series Manual de usuario
POSIFLEX
POSIFLEX Jiva TP-8000 Manual de usuario
POSIFLEX
POSIFLEX KV-2000 Series Manual de usuario
POSIFLEX
POSIFLEX Jiva 5815 Pro Manual de usuario
POSIFLEX
POSIFLEX XT-4015 Manual de usuario
POSIFLEX
POSIFLEX TX-4200 Manual de usuario
POSIFLEX
POSIFLEX TX-3000 Series Manual de usuario
POSIFLEX
POSIFLEX KS - 2010 Manual de usuario
POSIFLEX
POSIFLEX KS - 7212/X Manual de usuario
POSIFLEX
POSIFLEX RT-1016A-G2 Manual de usuario
POSIFLEX
POSIFLEX RT-2015E Manual de usuario
POSIFLEX
POSIFLEX XT-3817-G2 Manual de usuario
POSIFLEX
POSIFLEX KS - 6215N Manual de usuario
POSIFLEX
POSIFLEX XT-3815 Manual de usuario
POSIFLEX
POSIFLEX LM-31XXE Manual de usuario
POSIFLEX
POSIFLEX HT-3200 SERIES Manual de usuario
POSIFLEX
POSIFLEX XT-5415 Manual de usuario
POSIFLEX
POSIFLEX PS-3416 Manual de usuario
POSIFLEX
POSIFLEX KS - 6910 series Manual de usuario
