Planet NOVA100 Series Manual de usuario
NOVA100 series
FN-500
FN-800
Palm Top
Fast Ethernet Stackable Hub
EMFN5/800
2
Trademarks
Copyright PLANET Technology Corp. 1996.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET
Technology Corp. The information in this manual is
subject to change without notice. All other trademarks
belong to their respective owners.
FCC Warning
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated
in a commercial environment. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance
with the Instruction manual, may cause harmful
interference to radio communications. Operation of
this equipment in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at his own
expense.
3
Table of Contents
1Unpacking Information
Check List 5
Product Features 6
2General Description
About FN-500/FN-800 7
Front Panel of FN-500/FN-800 7
Rear Panel of FN-500/FN-800 9
3Installation
Hardware Installation 11
General Rules 11
Connecting End Nodes 12
Stacking two Hubs 13
Hub to Hub Connection, through Uplink port 14
Connecting the Hub to AC Power 15
4Troubleshooting 17
Appendix
Product Specification 19
FN-500/FN-800 User’s Manual 5
1. Unpacking Information
Check List
Carefully unpack the package and check its contents against
the checklist given below.
Checklist of 5/8-port 100Base-TX Fast Ethernet Hub
•NOVA100 5/8-port Palm-Top Fast Ethernet hub
•User’s manual
•AC Power Adapter and Power Cord
•RS-232 Stackable cable
•Accessories
Please inform your dealer immediately for any wrong, missing,
or damaged part if possible, retain the carton including the
original packing materials, and use them against to repack
the product in case there is a need to return it to us for repair.
PLANET NOVA100 Series
6
Product Features
•Conforms to IEEE 802.3U 100Base-TX standard
•Provides LED indicators for monitoring overall hub
condition and individual port status
•Automatic bad port partitioning to protect the network
•Two expansion connectors for stacking up to 5 hubs
together, and confirming Class II specification
•For desktop or wall-mounted installation
FN-500/FN-800 User’s Manual 7
2. General Description
About FN-500/ FN-800
This section describes the important parts of NOVA 100 5/8-
port Fast Ethernet hub. It presents front panel and rear panel
drawings of the product showing the LEDs, connectors, and
switches.
FN-500: 5-port Palm-Top Fast Ethernet Stackable Hub
FN-800: 8-port Palm-Top Fast Ethernet Stackable Hub
Front Panel of FN-500/ FN-800
The following figure shows the front panel of FN-500/FN-
800 100Base-TX Fast Ethernet hub.
1 2 3 4 5UpLink
Networking & Comm unic ation
FN-500
PWR
COL
1 2 3 4 5
LINKTX/RX
Figure 1. Front Panel of FN-500
1 2 3 4 5 6 7 8
UpLink
Networking&Communication
FN-800
PWR
COL
1 2 3 4 5 6 7 8
LINKTX/RX
Figure 2. Front Panel of FN-800
There are 5/8 (five/eight) RJ-45 ports and one “Uplink”port
on the front panel. Each port is labeled with a port number.
One special port labeled with “Uplink”is converted from
PLANET NOVA100 Series
8
port#1. You can either use Port#1 or “Uplink”port. The
“Uplink”port is used for connecting another hub through an
ordinary straight-wired twisted-pair cable by running one end
of straight cable to “Uplink”port and the other end to another
hub’s station port.
On the front panel, there are several LED indicators for
monitoring the device itself, and the network status. At a
quick glance of the front panel, the user would be able to tell
if the product is receiving power; if it is monitoring another
hub or concentrator; or if a problem exists on the network.
LED Indications
The following describes the function of each LED indicator.
LEDs Status Descriptions
PWR
(Power LED) Steady
Green This LED light is located at the left
side on the front panel. It will light
up(ON) to show that the product is
receiving power. Conversely, no light
(OFF) means the product is not
receiving power.
COL
(Collision
LED)
Blink
Red A “collision”in Ethernet, is when
two end nodes transmit at the same
time. The indicator lights up
whenever there is a collision between
a directly attached end node and any
other node
FN-500/FN-800 User’s Manual 9
LEDs Status Descriptions
LNK
(Link LEDs) Steady
Green Each RJ45 station port on the hub is
assigned an LED light for monitoring
port "Good Link and Activity". Each
LED is normally OFF after the power
on operation, but will light up
steadily to show “Good Link”.
TX/RX
(Activities
LEDs)
Blink
Green Each LED is normally OFF after the
power on operation and flash to show
that transmit and receive signals are
passing in and out the hub. The
flashing rapidly increases with the
network traffic.
Rear Panel
On the rear panel there are power DC jack, ID switch and two
expansion connectors. The following describes the function of
each connector and switch.
Figure 3 Rear panel of FN-500
Figure 4 Rear panel of FN-800
PLANET NOVA100 Series
10
DC Power Jack
The power cord should be plug into this socket. The DC jack
accept DC power equal to 5 Volt , 2 Amp, minimum for FN-
500 and 4 Amp. minimum for FN-800.
ID Switch
This switch is for setting the address of each hub when stack
two or more hubs together. Each hub should have one unique
number. The switch has four positions (No.1 to 4), therefore,
there are 16 possible combinations, except the setting of all
positions at OFF is not allowed;i.e. 15 combinations only is
accepted. For example, the settings from position No.1 to 4
are “off off on on”, the corresponding ID number is “3”.
Expansion Connectors
For FN-500/FN-800, there are two DB25 female connectors at
rear panel . These two connectors have the same function then
user can stack another hub by choosing any one of them.
Therefore, if one is used for “stack up”, then the other is for
“stack down”. Any combination of 5/8 port hub is allowed
only within the limitation of 5 hubs in one stack.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Cambiar de Planet
Planet
Planet WSW-2401A Manual de usuario
Planet
Planet GS-5220-24T4XVR Manual de usuario
Planet
Planet FSD-504HP Manual de usuario
Planet
Planet GSD-808HP Manual de usuario
Planet
Planet IGS-504HPT Manual de usuario
Planet
Planet GSD-805 Manual de usuario
Planet
Planet WGS-804HPT Manual de usuario
Planet
Planet FGSW-1828PS Manual de usuario
Planet
Planet uh-400 Manual de usuario
Planet
Planet WGS-5225-8MT Manual de usuario
Planet
Planet FGSW-2620VM Series Manual de usuario
Planet
Planet LRP-422CST Manual de usuario
Planet
Planet IGS-10020PT Manual de usuario
Planet
Planet FSD-808P Manual de usuario
Planet
Planet KVM-810 Manual de usuario
Planet
Planet ISW-504PS Manual de usuario
Planet
Planet IGS-10020M Manual de usuario
Planet
Planet KVM-800 Manual de usuario
Planet
Planet IFB-244-SLC Manual de usuario
Planet
Planet FGSW-4840S Manual de usuario
