Planet WNAP-7200 Manual de usuario

802.11a/n Wireless LAN Outdoor CPE AP/Router

WNAP-7200

Quick Installation Guide

Table of Contents

1. Package Content.......................................................................................... 4

2. Hardware Installation ................................................................................... 5

3. Web Conguration ....................................................................................... 9

4. Further Conguration ..................................................................................10

Designed with the most innovative 802.11a/n technology, WNAP-7200 provides

maximum 150Mbps high data rate for outdoor environment. There are multiple

operating modes supported in WNAP-7200: Bridge, Gateway, WISP, and built-

in 18dBi at panel antenna and high transmit output power make WNAP-7200 a

suitable CPE solution for widely open space applications such as WISP, campuses,

and airports. Except for 64/128-bit WEP encryption, WNAP-7200 integrates WPA,

WPA2 and 802.1x authentication to secure the information of your wireless LAN.

1. Package Content

WNAP-7200 x 1

PoE Injector x 1

Power Adapter x 1

Mounting Kit x 1

CD x 1

Quick Installation Guide x 1

Note

If any of the above items are missing or damaged, contact your

local dealer for support.

2. Hardware Installation

Before you proceed with the installation, it is necessary that you have enough

information about WNAP-7200.

1. Please connect right installation “PoE” port of PoE inject to WNAP-7200; “LAN”

port of PoE injector to LAN PC, wrong installation will cause the device damage.

Note

Strongly suggest using SFTP cable, for better protection of the data

wire. 25-meter SFTP cable also available by order, the part no is

CB-STP-25. Please contact with local dealer for more information.

2. Using Category 3 or higher UTP or STP cable, connect the “LAN” port of PoE

Injector to a 10Mbps or 10/100Mbps Ethernet hub or switch, and connect the PC

on the same LAN for management.

3. Locate an optimum location and use the provided Mounting kit to tie the WNAP-

7200 to a pole.

Note

1. To avoid thunder strike, consider installing ELA-100, thunder

arrester toward the CPE AP and the PoE injector.

2. For secured reason, while install the CPE AP, please be aware for

the electric wires around, and tighten the pole. Without tighten

the CPE AP, the pole and the installed site is with electric wire

around, there could be danger of being hurt by falling or lethal

injury.

4. Connect the 12V 1.25A DC power adapter to the PoE Injector socket, and plug it

into an AC outlet to power on the WNAP-7200.

Note

1. The PoE Injector is a passive device. It will inject the DC power

into the UTP cable right away once you connect the DC-plug in to

the DC-jack of the PoE Injector.

2. DONOT connect the PoE Injector labeled as POE port to any

devices but WNAP-7200, otherwise it will damage the device

permanently.

5. For Ethernet port application, please refer to user’s manual for bridge, gateway

and WISP application for the rst installation, LAN port is suggested.

Note

1. ONLY use the power adapter supplied with the WNAP-7200.

Otherwise, the product may be damaged.

2. Strongly suggest using STP cable whether the cable exposed

outdoor for waterproof and avoiding thunder stroke.

OUTDOOR INSTALLATION WARNING

IMPORTANT SAFETY PRECAUTIONS:

LIVES MAY BE AT RISK! Carefully observe these instructions and any special

instructions that are included with the equipment you are installing.

CONTACTING POWER LINES CAN BE LETHAL.

Make sure no power lines are

anywhere where possible contact

can be made. Antennas, masts,

towers, guy wires or cables may

lean or fall and contact these limes.

People may be injured or killed if

they are touching or holding any

part of equipment when it contacts

electric lines. Make sure there is

NO possibility that equipment or

personnel can come in contact

directly or indirectly with power lines.

Assume all overhead lines are power lines.

The horizontal distance from a tower, mast or antenna to the nearest power line

should be at least twice the total length of the mast/antenna combination. This will

ensure that the mast will not contact power if it falls either during installation or

later.

TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING

AT HEIGHTS ABOVE GROUND.

Select equipment locations that will allow safe, simple equipment installation.

Don’t work alone. A friend or co-worker can save your life if an accident

happens.

Use approved non-conducting lasers and other safety equipment. Make sure all

equipment is in good repair.

If a tower or mast begins falling, don’t attempt to catch it. Stand back and let it

fall.

If anything such as a wire or mast does come in contact with a power line,

DON’T TOUCH IT OR ATTEMPT TO MOVE IT. Instead, save your life by

calling the power company.

Don’t attempt to erect antennas or towers on windy days.

MAKE SURE ALL TOWERS AND MASTS ARE SECURELY

GROUNDED, AND ELECTRICAL CABLES CONNECTED TO

ANTENNAS HAVE LIGHTNING ARRESTORS.

This will help prevent re damage or human injury in case of lightning, static build-

up, or short circuit within equipment connected to the antenna.

The base of the antenna mast or tower must be connected directly to the

building protective ground or to one or more approved grounding rods, using 1

OAWG ground wire and corrosion-resistant connectors.

Refer to the National Electrical Code for grounding details.

IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER,

AND CANNOT MOVE:

DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.

Use a non-conductive dry board, stick or rope to push or drag them so they no

longer are in contact with electrical power.

Once they are no longer contacting electrical power, administer CPR if you are

certied, and make sure that emergency medical aid has been requested.

3. Web Conguration

WNAP-7200 provides a user friendly interface for users to congure via web

browser. Please follow the below steps to congure WNAP-7200 basic settings.

1. It will take around 40 seconds to complete the boot up sequence after power on

from PoE.

2. Open your web browser and type default IP address of WNAP-7200

(http://192.168.0.1) into the “Address Field” of you web browser. Before

conguration, please make sure your PC’s IP address is under the same IP range

with WNAP-7200, such as 192.168.0.x.

3. After entering, ll the default username/password (admin / admin) and then

you can see the home page.

4. Further Conguration

For more settings of WNAP-7200, please refer to the user’s manual in the CD.

If you have any difculty on resolving the problem while installing or using the

device, please feel free to contact your local dealer or PLANET Technical Support.

Otros manuales para WNAP-7200

Tabla de contenidos

Otros manuales de Enrutador de red de Planet

Planet

Planet WGSD-10020 Manual de usuario

Planet

Planet ADN-4101 Manual de usuario

Planet

Planet MGSW-28240F Manual de usuario

Planet

Planet FNSW-4800 Manual de usuario

Planet

Planet RT-101 Manual de usuario

Planet

Planet FWA-2100-NR Manual de usuario

Planet

Planet MH-3400 Manual de usuario

Planet

Planet GS-4210 SERIES Manual de usuario

Planet

Planet ADSL Firewall Router ADE-4120 Manual de usuario

Planet

Planet FNSW-2400PS Manual de usuario

Planet

Planet VIP-280 Manual de usuario

Planet

Planet ADE-3410 Manual de usuario

Planet

Planet GSD-802S Manual de usuario

Planet

Planet WGD-800 Manual de usuario

Planet

Planet EPN-102 Manual de usuario

Planet

Planet ISW-500T Manual de usuario

Planet

Planet VC-234G Manual de usuario

Planet

Planet VR-100 Series Manual de usuario

Planet

Planet ADE-3400 Manual de usuario

Planet

Planet GS-5220-48T4X Manual de usuario

Planet

Planet ADE-4301A Manual de usuario

Planet

Planet ADE-3410 Manual de usuario

Planet

Planet IGS-5225-20T4C2X Manual de usuario

Planet

Planet FSD-805 Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad