Planet FT-801 Manual de usuario

Contents subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technol-

ogy Corp. The information in this manual is subject to

change without notice. All other trademarks belong to

their respective owners.

Disclaimer

PLANET Technology does not warrant that the hardware

will work properly in all environments and applications,

and makes no warranty and representation, either

implied or expressed, with respect to the quality, per-

formance, merchantability, or tness for a particular

purpose.

PLANET has made every effort to ensure that this User’s

Manual is accurate; PLANET disclaims liability for any

inaccuracies or omissions that may have occurred.

Information in this User’s Manual is subject to change

without notice and does not represent a commitment on

the part of PLANET. PLANET assumes no responsibility

for any inaccuracies that may be contained in this User’s

Manual. PLANET makes no commitment to update or

keep current the information in this User’s Manual, and

reserves the right to make improvements to this User’s

Manual and/or to the products described in this User’s

Manual, at any time without notice.

If you nd information in this manual that is incorrect,

misleading, or incomplete, we would appreciate your

comments and suggestions.

FCC Warning

This equipment has been tested and found to comply

with the regulations for a Class A digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference when the equipment is operated in

a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not

installed and used in accordance with this user’s guide,

may cause harmful interference to radio communica-

tions. Operation of this equipment in a residential area

is likely to cause harmful interference, in which case the

user will be required to correct the interference at his

own expense.CE mark Warning

This is a Class A product. In a domestic environment,

this product may cause radio interference, in which case

the user may be required to take adequate measures.

CE Mark Warning

This is a Class A product. In a domestic environment,

this product may cause radio interference, in which case

the user may be required to take adequate measures.

Revision

User’s manual for PLANET Fast Ethernet Converter

Multi-mode: FT-801, FT-802, FT-803

Single-mode: FT-802S15, FT-802S35, FT-802S50,

FT-806A20, FT-806B20

Rev 6.0 (September. 2004)

Part No. 2010-000002-005

Table of Contents

Chapter 1 Overview 1

Chapter 2 Model List 1

Chapter 3 Checklist 2

Chapter 4 Product Outlook 2

Chapter 5 Link Fault Pass through (LFP) 3

Chapter 6 Installing the Converter 6

Chapter 7 Duplex Mode setting 7

Chapter 8 LED indication 8

Chapter 9 Cable Connection Parameter 9

Chapter 10 FT-80X Technical Specifications 10

Chapter 11 Power information 11

Chapter 1

Overview

Thank you for purchasing PLANET FT-80X family 10/100Mbps

Ethernet Twisted pair to 100Base-FX Fiber-optic Bridge Converter.

This converter is used to convert one type media signal to other

type equivalent that allows two type segments connect easily,

efciently and inexpensively. This converter can be used as a

standalone unit or as a slide-in module to the 10”/19” media

chassis (up to 15 units) for a TP and Fiber combined networks at a

central wiring closet. Please contact with your sales representative

for more about the 19” media chassis.

Chapter 2

Model List

Your Fast Ethernet Converter comes with one of the following

models.

ð FT-801: on board ST fiber connector

ð FT-802/S: on board SC fiber connector

ð FT-803: on board MTRJ fiber connector

ð FT-806A20: on board single SC fiber connector

ð FT-806B20: on board single SC fiber connector

Models with last character “S” indicate the ber-port is with

“Single-Mode” optic ber connector and followed with a number

indicates the maximum wiring distance.

In the following sections, the term “FT-80X” indicates the product

family above.

Chapter 3

Checklist

Your FT-80X carton should contain the following items:

ð The Fast Ethernet Bridge Converter

ð AC-DC Power Adapter (Output: 5VDC, 2 A max.)

ð This user’s manual

If any item is missing or damaged, please consult the dealer from

whom you purchased your Fast Ethernet Converter.

Chapter 4

Product Outlook

Right View

There are one RJ-45 Twisted-Pair jack (Auto-MDI/MDI-X), one

ber-optic connector (vary by model) and six LED indicators.

Left View

One DIP switch for Fiber-optic operating mode selection, FDX for

full-duplex, and HDX for half-duplex.

Side View (FT-80X)

One DIP switch for Link Fault Pass Through (LFP) feature, “ON”

to turn-on the LLCF and LLR detection. And “OFF” to turn–off this

feature. Please refer to the following sections for more.

DIP Switch for LFP function.

Chapter 5

Link Fault Pass through (LFP)

The LFP function includes the Link Fault Pass Through function

(LLCF/LLR) and the DIP Switch design. LLCF/LLR can immediately

alarm administrators the problem of the link media and provide

efcient solution to monitor the net. The DIP Switch provides

disable or enable the LFP function.

LLCF (Link Loss Carry Forward) means when a device connected

to the converter and the TP line loss the link, the converter’s ber

will disconnect the link of transmit. LLR (Link Loss Return) means

when a device connected to the converter and the ber line loss

the link, the converter’s ber will disconnect the link of transmit.

Both can immediately alarm administrators the problem of the link

media and provide efcient solution to monitor the net.

Link Loss Carry Forward (LLCF)

FT-80X incorporates an LLCF function for troubleshooting a

remote connection. When LFP function is enabled, the FL/TP ports

do not transmit a link signal until they receive a link signal from

the opposite port.

The diagram below shows a typical network conguration with a

good link status using FT-80X for remote connectivity.

If the connection breaks, FT-80X that link loss forward to the

switch/hub that generates a trap to the management station. The

administrator can then determine the source of the problem.

*Units are shipped with the LFP function enabled (ON).

Link Loss Return (LLR)

The ber ports of FT-80X have been designed with an LLR function

for troubleshooting a remote connection. LLR works in conjunction

with LLCF.

When LFP function is enabled *(by default), the port’s transmitter

shuts down when its receiver fails to detect a valid receive link.

LLR should only be enabled on one end of the link and is typically

enabled on either the unmanaged or remote device.

The diagram below shows a typical network conguration with a

good link status using FT-80X for remote connectivity. Note that

LLR and LLCF are enabled as indicated in the diagram.

If one of the optical conductors is bad (as shown in the diagram

box below), the converter with LLR function will return a no-link

condition to its link partner. With LLCF function also enabled, the

no-link condition is carried forward to the switch/hub where a trap

is generated to the management station, and the administrator

can then determine the source of the loss.

 NOTE:

LFP function is turn-on in default. This feature

can also be turned off via the side DIP-switch.

If you are familiar with the network installation

and for diagnostic purpose (i.e. check which

end is broken), you can turn it off and reset

the converter to make it take effect. Otherwise,

please remains it in the default position.

Chapter 6

Installing the Converter

Please follow these steps to install the converter:

• Turn off the power of the device/station in a network to

which the FT-80X will be attached

• Ensure that there is no activity in the network

• Attach fiber cable from the FT-80X to the fiber network.

TX, RX must be paired at both ends

• Attach a Cat. 5 UTP cable from the 10/100Base-TX net-

work to the RJ-45 port on the FT-80X.

• Connect the 5VDC power adapter to the FT-80X and

verify that the Power LED lights up.

• Turn on the power of the device/station, the TX Link and

FX Link LEDs should light when all cables are attached

• Turn on the power of the device/station, the TX Link and

FX Link LEDs should light when all cables are attached

 NOTE:

• RJ-45/STP, UTP Cat 5, straight/crossover

cable is accepted

• Please refer to section 8 for more about

the wiring distance of your TP, Optic-ber

networks.

Otros manuales para FT-801

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Convertidor de medios de Planet

Planet

Planet IECC-210T Manual de usuario

Planet

Planet Power over Ethernet Splitter POE-152S-12V Manual de usuario

Planet

Planet ICS-2100 Manual de usuario

Planet

Planet VC-102M Manual de usuario

Planet

Planet vc-234 vdsl2 Manual de usuario

Planet

Planet ICS-10 Series Manual de usuario

Planet

Planet GTP-805A Manual de usuario

Planet

Planet VF-101-T Manual de usuario

Planet

Planet VC-232G Manual de usuario

Planet

Planet XT-705A Manual de usuario

Planet

Planet ICS-2100 Manual de usuario

Planet

Planet GT-902 Manual de usuario

Planet

Planet FT-807 Manual de usuario

Planet

Planet WFT-201 Manual de usuario

Planet

Planet IXT-705AT Manual de usuario

Planet

Planet IGT-1205AT Manual de usuario

Planet

Planet WGT-705A Manual de usuario

Planet

Planet GT-922 Manual de usuario

Planet

Planet GT-1205A Manual de usuario

Planet

Planet POE-161S Manual de usuario

Planet

Planet FT-722 Manual de usuario

Planet

Planet IFT-802T Manual de usuario

Planet

Planet VC-201A Manual de usuario

Planet

Planet vc-231 Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario