Planet Networking & Communication BSP-360 Manual de usuario

Industrial Renewable Power

5-Port Gigabit Managed Switch/Router

with 4-Port 802.3at PoE+

BSP-360

Quick Installation Guide

Safety Precautions

Please read the following before using:

1. All electrical work must be done in accordance with local, and/or international

electrical codes.

2. Before installing or using this device, read all instructions and cautionary

marking located in (or on) this guide, the controller, the batteries, PV (Photovol-

taic) array and any other device used.

3. To reduce the risk of short-circuits, use insulated tools when installing or working

with the inverter, the controller, the batteries, or any DC source (e.g., PV).

4. Remove all jewelry. This will greatly reduce the chance of accidental exposure to

live circuits.

5. The controller contains more than one live circuit (batteries and PV array).

Power may be present at more than one source.

6. This product contains no user serviceable parts. Do not attempt to repair this

unit unless fully qualied.

Table of Contents

1. Package Contents ....................................................................................... 4

2. Requirements ............................................................................................. 5

3. Hardware Introduction ................................................................................ 6

3.1 Front Panel ......................................................................................... 6

3.2 LED Indicators..................................................................................... 7

3.3 Upper Panel ........................................................................................ 8

4. Hardware Installation .................................................................................10

5. Web Management ......................................................................................16

6. Deployed Devices Monitored via NMS-360 Controller.....................................18

7. Customer Support .....................................................................................20

Appendix A: Recommended Use of the Connected Wires....................................21

Appendix B: Recommended Settings for Batteries..............................................22

1. Package Contents

Thank you for purchasing PLANET Industrial Renewable Energy Managed PoE

Switch/Router, BSP-360. Open the box of the BSP-360 and carefully unpack it. The

box should contain the following items:

1 x BSP-360 1 x Quick Installation Guide

1 x Wall Mounting Kit 1 x DIN Rail Kit 5 x RJ45 Dust Cap

If any of these are missing or damaged, please contact your dealer immediately. If

possible, retain the carton including the original packing materials to enable you to

repack the product in case there is a need to return it to us for repair.

2. Requirements

PLANET BSP-360 provides a remote login interface for management purposes. The

following equipment is necessary for further management:

Workstation is installed with Ethernet NIC (Network Interface Card)

Choice of Internet browsers includes Windows XP/2003, Vista, Windows 7,

Windows 8, Windows 10, MAC OS X, Linux, Fedora, Ubuntu or other platforms

compatible with TCP/IP protocols.

The above workstation is installed with Web browser and JAVA runtime envi-

ronment plug-in.

Ethernet Port connection

Use standard network (UTP) cables with RJ45 connectors.

PV and battery

Two 12V lead-acid batteries connected in series or one 24V lead-acid battery.

The maximum operating voltage of PV is 45V

Note

It is recommended to use Internet Explorer 8.0 or above to access

the BSP-360.

3. Hardware Introduction

3.1 Front Panel

The front panel of the BSP-360 consists of 5 auto-sensing 10/100/1000Mbps

Ethernet RJ45 ports and one USB interface. The LED Indicators are also located on

the RJ45 ports of the BSP-360.

V1+

Reset

V2+

BSP-360

PWR Fault PV System

50W 100W 120W

5/WAN

PoE Power

Usage

ACTLNK

PoE-in-Use

Industrial Renewable Energy Managed PoE+Switch

DC Ouput: 24V , 1A max.

Figure 3-1 shows the front panel of BSP-360

Item Interface Description

1Port-1~Port-4 4 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports with

802.af/at PoE+ injector function.

2Port-5

One 10/100/1000BASE-T RJ45 auto-MDI/MDI-X port.

Port-5 functions as WAN port when the operation

mode of BSP-360 is congured to “Gateway mode”.

3USB Connect the USB storage to USB port and back up the

conguration le.

4Reset Button < 5 seconds: System reboot.

> 5 seconds: Factory default.

54-pin Terminal

Block

2 x 24V 1A DC output connector.

The output voltage is the same as battery voltage.

Maximum power output is clamped at 24W.

3.2 LED Indicators

System

LED Color Function

PWR Green On To indicate BSP-360 has power.

Fault Red On To indicate bad battery, over-current or short-

circuit.

System Green

Slow

Blinks To indicate the system is “on”.

Fast

Blinks To indicate the battery is “charging”.

50W Orange On To indicate the system consumes over 50-watt

PoE power budget.

100W Orange On To indicate the system consumes over 100-watt

PoE power budget.

120W Orange On To indicate the system consumes the total

120-watt PoE power budget.

PoE 10/100/1000BASE-T Interfaces (Port-1 to Port-4)

LED Color Function

LNK/ACT Green Blinks To indicate the link through that port is

successfully established.

PoE Orange

Lights To indicate the port is providing DC in-line power.

O To indicate the connected device is not a PoE

Powered Device (PD).

10/100/1000BASE-T Interfaces (Port-5)

LED Color Function

LNK/ACT Green Blinks To indicate the link through that port is

successfully established.

3.3 Upper Panel

The upper panel of the BSP-360 consists of one terminal block connector with PV

and battery power inputs.

Bat.

PV Fault

+ +

PV DC Input:

24-45V , 6A max. Battery DC Input: 24V , 6A

Max. fault loading: 24V, 1A

1 2 3 4 5 6

Figure 3-2 Upper Panel

The input voltage range of each interface is shown as follows:

PV In Connector

24~45V DC

Bat.

PV Fault

+ +

PV DC Input:

24-45V , 6A max. Battery DC Input: 24V , 6A

Max. fault loading: 24V, 1A

1 2 3 4 5 6

Solar PV

24~45V DC

Figure 3-3 PV In Connector

Battery In/Out

24V DC

Bat.

PV Fault

+ +

PV DC Input:

24-45V , 6A max. Battery DC Input: 24V , 6A

Max. fault loading: 24V, 1A

1 2 3 4 5 6

Battery

24V DC

Figure 3-4 Battery In/Out

Note

The wire gauge for the terminal block should be in the range from

14 to 24 AWG.

Fault Connectors

Level 0: -24V~2.1V (±0.1V)

Level 1: 2.1V~24V (±0.1V)

1 2 3 4 5 6

Fault

Load

5~24VDC

GND

4. Hardware Installation

The following section describes the hardware installation of the BSP-360. Before

connecting any network device to the BSP-360, read this chapter carefully.

BSP-360

Battery

CAM1 CAM2 CAM3

Outdoor

Wireless AP

PoE

PoE PoE PoE

Ethernet Switch

Media Converter/

DC Powered Device Monitoring Center

Solar PV

DC Power Line (DC)

1000BASE-T UTP

PoE

1000BASE-T UTP with PoE

2.4GHz 802.11n

Caution

Equipmentmust

begrounded

PoEIn:802.3at PoE

Don’tturn“A” when

attaching“B”

Surgearresterisrequired and

mustbegrounded

Theproperantennamust be

connectedbeforepowering

theAPon

Please follow the following steps to install the system:

Step 1. Install BSP-360

Place the BSP-360 in a desired location using the wall-mount xtures.

Note

a. Please install the BSP-360 in a proper enclosure or shelter.

b. The BSP-360 must be grounded.

Otros manuales para BSP-360

Tabla de contenidos

Otros manuales de Cambiar de Planet Networking & Communication