Planar AX3 Manual de usuario

AX3 Display Controller

QUICK REFERENCE

Windows XP

Windows 2000

020-0424-00A-AX3-QRUG 11/16/05 8:59 PM Page 1

Experienced users and system administrators can follow the

instructions in this document to install the AX3 display controller.

This board provides dual display functionality.

Check the system requirements and the safety precautions on page 3.

Then follow this order of installation for the Dome display system.

1 Install the AX3 display controller into your computer.

2 Connect one or two displays to the display controller.

3 Install the display driver.

4 Configure the display(s).

5 Install the Dome CXtra software.

For more information, refer to the user’s manuals for the display and

the Dome CXtra software.

020-0424-00A-AX3-QRUG 11/16/05 8:59 PM Page 2

Before You Begin

Check that your system meets these requirements and runs one of these

Microsoft operating systems.

Warning

Avertissement

Avvertenza

Advertencia

Warnung

Before disconnecting a peripheral or removing a component

from the motherboard, wait 20 seconds after unplugging the

power cord to avoid possible damage to the motherboard.

Wear an antistatic heel or wrist strap when installing the board

to avoid damage to computer components.

Discharge your body’s static electricity by touching the power

supply or the metal surface of the computer chassis.

Operating System

Windows XP or

Windows 2000

with Service Pack 4

or higher

System Requirements

•Intel Pentium 4/Xeon; AMD

Athlon 64/K7/XP or compatible

•PCI Express x16 lane slot

•50 MB hard disk space

•256 MB RAM

•CD-ROM drive

•Power supply,

350 watts or greater

EX Display Display Controller

Dome E3 AX3

Dome E3c

Dome E4c

020-0424-00A-AX3-QRUG 11/16/05 8:59 PM Page 3

Installing the Display Controller

Open PCI Express slot

AX3 controller

installed

Blank bracket

Remove any existing graphics card and its driver from your computer system before you

install the AX3 controller and driver. Also disable any onboard graphics capability on the

motherboard. See safety precautions on page 3.

To install the controller

1 Turn off your computer and all peripherals.

Disconnect all cables from your computer.

Leave the power cord plugged into the

grounded outlet.

2 Remove the computer cover.

3 Remove any existing graphics card and

video signal cable, if necessary.

4 Remove the blank bracket from the available

PCI Express slot.

5 Insert the controller into the slot,

align the connector pins, and press the

board down until it is firmly seated.

6 Secure the mounting bracket.

7 Reattach the computer cover and the peripherals.

020-0424-00A-AX3-QRUG 11/16/05 8:59 PM Page 4

Use only the cables and power cord supplied with your display.

To connect the display

1 Plug one end of the DVI signal cable to

the DVI port on the display. Tighten the

thumbscrews to secure the connection.

2 Plug the power cord into the power

input port.

3 Plug the other end of the DVI cable into

the video port on the installed controller.

(Use DVI port #1 for the first display if you

are installing only one display.)

4 Plug the other end of the power cord

into a grounded outlet.

5 Repeat steps 1 to 4 to connect a second

display to the controller.

6 Power on your display first, then

the computer.

Connecting the Display

Connection

for a single

display or the

first display of

a dual setup

DVI cable

AX3 controller

installed

DVI port 1

DVI port 2

020-0424-00A-AX3-QRUG 11/16/05 8:59 PM Page 5

Installing the Display Driver

Before you install the driver, remove any previously installed display driver for the display

controller from your system.

To install the driver

1 Start the system. Click Cancel on the Found New Hardware Wizard. Click No when the

system prompts you to restart the computer.

2 Insert the driver installation CD and run SETUP.EXE.

3 Click Next.

4 Click Yes to the license agreement. The installation starts.

5 Follow the onscreen instructions to complete the installation. Planar recommends that

you select the Express installation option.

6 When the Setup complete message appears, select Yes, I want to restart my computer

now and click Finish.

7 If the Digital Signature Not Found message appears, click Yes or Continue to complete

the driver installation.

020-0424-00A-AX3-QRUG 11/16/05 8:59 PM Page 6

Use the Display Properties dialog to make changes to the video settings.

To set the display mode manually

1 Right-click the desktop and select Properties > Settings.

2 Select the monitor that you want to change.Then click Advanced.

3 Click the Monitor tab. Make sure that the check box for Hide modes that this monitor

cannot display is empty (unchecked).

4 Click the Adapter tab, then click the List All Modes button.

5 Choose the mode and click OK.Then click Apply or OK.

To set the brightness

You must have the Dome CXtra software installed to change the display brightness. Adjust

the value of the white level on the Backlight tab of the RightLight Panel Configuration.

Adjusting the Display Properties

020-0424-00A-AX3-QRUG 11/16/05 8:59 PM Page 7

America Sales

Planar Systems, Inc.

1195 NW Compton Drive

Beaverton, OR 97006-1992 USA

phone + 1 (503) 748-1100

fax + 1 (503) 748-1493

Medical Sales

Planar Systems, Inc.

400 Fifth Avenue

Waltham, MA 02451-8738 USA

phone + 1 (781) 895-1155

fax + 1 (781) 895-1133

Europe Sales

European Representative

Planar Systems, Inc.

Olarinluoma 9, P. O. Box 46

FIN-02201 Espoo, Finland

phone + 358 9 420 01

fax + 358 9 420 0200

Asia-Pacific Sales

Planar Systems, Inc.

388 Nan Jing West Road, Suite 3905

Shanghai Peoples Republic of China

phone + 86 21 6334 5050

fax + 86 21 6334 6339

Customer Support

•Visit www.planar.com

•E-mail medicalsupport@planar.com

•Call (866) PLANAR1

Technical information in this document is subject to change without notice.

020-0424-00B

020-0424-00A-AX3-QRUG 11/16/05 8:59 PM Page a

Tabla de contenidos

Otros manuales de Controladores de Planar

Planar

Planar Dome Md2/PCI Manual de instrucciones

Planar

Planar AX4 Manual de usuario

Planar

Planar Dome M2/PCI Manual de usuario

Planar

Planar RX/PCI Manual de usuario

Planar

Planar Dome Md5/PCI Manual de usuario

Planar

Planar RPS Manual de usuario

Planar

Planar DOME Md4/PCV Manual de usuario

Planar

Planar Dome M2/PCI Manual de instrucciones

Planar

Planar P1 Manual de usuario

Planar

Planar DOME Md4/PCX Manual de usuario

Planar

Planar Dome Md2/PCI Manual de usuario

Planar

Planar Dome Md4/PCI Manual de usuario

Planar

Planar DX/PCI Manual de usuario

Planar

Planar DOME Md5/PCX Manual de usuario

Planar

Planar DOME Md5/DFP Manual de usuario

Planar

Planar EX2 Manual de usuario

Planar

Planar PU-16 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario