Pioneer DR-704S Manual de usuario
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presenceofuninsulated"dangerousvoltage"withinthe
product'senclosurethatmaybeofsufficientmagnitude
to constitute a risk of electric shock to persons.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
IMPORTANT
CAUTION:
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER-
SERVICEABLEPARTSINSIDE. REFERSERVICING
TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equilateral triangle is
intendedto alert theuser to thepresence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
English
Français
Deutsch
IMPORTANT NOTICE:
RECORD THE MODEL NUMBER
AND SERIAL NUMBER OF THIS
EQUIPMENT BELOW. THE NUM-
BERS ARE ON THE TOP PANEL.
MODEL NO. DR-A14S
SERIAL NO.
KEEP THESE NUMBERS FOR
FUTURE USE.
CD-ROM DRIVE UNIT
UNITE DE LECTEUR DE CD-ROM
CD-ROM –LAUFWERK
LETTORE DI CD-ROM
Italiano
Operating instructions
Mode d’emploi
Bedienungsanleitung
Istruzioni per l'uso
Thank you for buying this PIONEER
product. Please read through these
operating instructions so you will
knowhowtooperateyourunitprop-
erly. After you have finished read-
ing the instructions, put them away
in a safe place for future reference.
WARNING: TO PREVENT FIRE
OR SHOCK HAZARD, DO NOT EX-
POSE THIS APPLIANCE TO RAIN
OR MOISTURE.
DR-A14S
BUSYPHONES
CD-ROM DRIVE
2
<DRC1085>
En
This product complies with the EMC Directives (89/336/EEC, 92/31/EEC) and CE
Marking Directive (93/68/EEC).
Ceproduitestconformeauxdirectivesrelativesàlacompatibilitéélectromagnétique
(89/336/CEE, 92/31/CEE) et à la directive CE relative aux marquages (93/68/CEE).
Dieses Produkt entspricht den EMV-Richtlinien (89/336/EEC, 92/31/EEC) und CE-
Markierungsrichtlinien (93/68/EEC).
Questo prodotto è conforme alle direttive EMC (89/336/CEE, 92/31/CEE) e alla
direttiva sul marchio CE (93/68/CEE).
Dit produkt voldoet aan de EMC-richtlijnen (89/336/EEC en 92/31/EEC) en de CE-
markeringsrichtlijn (93/68/EEC).
Denna produkt uppfyller föreskrifterna i EMC-direktiv (89/336/EEC, 92/31/EEC) och
CE-märkningsdirektiv (93/68/EEC).
Este producto cumple con las Directivas EMC (89/336/CEE, 92/31/CEE) y Directiva
de Marcación CE (93/68/CEE).
Este produto cumpre com as Directivas EMC (89/336/CEE, 92/31/CEE) e Directiva
da Marcação CE (93/68/CEE).
Dette produkt er i overensstemmelse med direktiverne vedrørende
elektromagnetisk kompatibilitet (89/336/EEC, 92/31/EEC) og CE-direktivet
vedrørende mærkning (93/68/EEC).
VARNING!
Om apparaten används på annat sätt än i denna bruksanvisning spacificerats, kan
användaren utsättas för osynling laserstrålning som överskrider gränsen för
laserklass 1.
ADVARSEL:
Usynlig laserstråling ved åbning når sikkerhedsafbrydere er ude af funktion. Undgå
udsaettelse for stråling.
VAROITUS!
Laitten käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa
altistaa käuttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
<DRC1085>
En
3
SAFETY INSTRUCTIONS
To ensure your personal safety and to maximize the full operating potential of your Drive, read
and follow these safety precautions:
ENVIRONMENT - Please do not use the unit at places with much dust, high temperature, or
high humidity. Please use the unit at a place where it is not subjected to vibrations or shocks.
POWER - Power-off your system and attached hardware devices before installation.
READ INSTRUCTIONS - Read all safety and operating instructions before the Drive is operated.
RETAIN INSTRUCTIONS - Retain the safety and operating instructions for future reference.
FOLLOW INSTRUCTIONS - Follow all operating and use instructions.
HEED WARNINGS - All warnings must be adhered to.
CLEANING - DO NOT use liquid, aerosol cleaners, or alcohol. Use only a damp cloth to clean
the exterior housing.
WATER AND MOISTURE - DO NOT use this product near water.
POWER SOURCES - Operate this product from the type of power source indicated on the
marking label. If you are not sure of the type of power available, consult your Authorized Pioneer
Dealer.
OVERLOADING - DO NOT overload wall outlets and extension cords. Doing so can result in
fire or electric shock.
OBJECT AND LIQUID ENTRY - Never push objects of any kind into this product. Touching
dangerous voltage points may cause a short resulting in fire or electric shock. Do not spill liquid
of any kind on this product.
CONDENSATION - Moisture will form in the operating section of the product causing
performance to be impaired if it is brought from cool surroundings into a warmer environment.
If you are moving the unit to a location with a warmer temperature, let the product stand for 1-
2 hours in the new location before turning it back on.
SERVICING - Do not attempt to repair this product yourself. Opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel. (Refer to the enclosed Service and Support Card.)
IMPORTANT
CAUTION
This product contains a laser diode of higher class than
1. To ensure continued safety, do not remove any
covers or attempt to gain access to the inside of the
product.
Refer all servicing to qualified personnel.
The following caution label appears
on your unit.
Location: on top of the cover
Forpluggableequipmentthesocket-outletshallbeinstallednear
the equipment and shall be easily accessible.
CLASS 1 LASER PRODUCT
LASER KLASSE 1
4
<DRC1085>
En
SAFETY INSTRUCTIONS
[For Canadian model]
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
RADIO SIGNAL INTERFERENCE - This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses,
andcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation.Ifthis equipment does cause harmful interference toradioortelevision
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
]Reorient or relocate the receiving antenna.
]Increase the separation between the equipment and receiver.
]Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
]Consult the dealer or an experienced radio/TV technician for help.
LASER DIODE - This product contains a laser diode. To assure continued safety,
DO NOT removeany convers or attempt to gain access totheinside of the product.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
CAUTION: USE OF OPTICAL INSTRUMENTS WITH THIS PRODUCT WILL INCREASE EYE
HAZARD.
Information to User
Alteration or modifications carried out without appropriate authorization may invalidate the
user’s right to operate the equipment.
The Generation of Acoustical Noise Is Less Than 70dB.
(ISO7779/DIN45635)
[Pour le modèle Canadien]
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
<DRC1085>
En
5
SAFETY INSTRUCTIONS
The enclosed device driver is for use with MS-DOS/Windows 3.XX. This driver is
not required for use with Windows 95.
* MS-DOS and Windows are trademarks of Microsoft Corporation.
DO NOT use non-standard discs, as these may adversely influence
this unit and other equipment.
DO NOT use damaged,cracked, or warped discs. If they break inside
the unit, they may damage the optics. Discs rotate at high speed in-
side the changing mechanism.
DO NOT play a CD having other shape than a circular disc, such as
heart shaped disc. Otherwise malfunction may occur.
FEDERAL COMMUNICATIONS COMMISSION
DECLARATION OF CONFORMITY
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Product Name: CD-ROM DRIVE UNIT
Model Number: DR-A14S
Responsible Party Name: PIONEER ELECTRONICS SERVICE, INC.
Address: 1925 E. DOMINGUEZ ST. LONG BEACH, CA 90810 U.S.A.
Phone: (310) 952-2359
6
<DRC1085>
En
FEATURES
÷High-speed reading
Transfer rate (sustained):
2,100 kBytes/sec. – 5,400 kBytes/sec. (CAV 36X max)
÷High-speed access
Random average: 70 ms
÷Low vibration mechanism
÷ATAPI correspondence
÷Buffer size: 128 kBytes
÷Applicable discs
CD-ROM Mode 1
CD-ROM XA Mode 2 (Form 1, 2)
CD-DA (Digital audio output)
CD Extra, Video CD, CD-I Ready and CD-XA Ready support
CD-RW disc reading
NOTES:
This product can read out CD-RW disc data. Note the following:
(1) A little longer time is needed to sense a CD-RW disc when the operation starts, compared
with normal CD-ROM discs.
(2) The read-out speed of CD-RW discs is usually 4 times higher than that of normal discs.
However, according to the quality of the disc or under extremely hot or cold conditions,
the player may reduce the speed of rotation of the disc during read-out. (Because the
reproduced signal level from CD-RW discs is lower than that of normal discs.)
(3) Blank discs, discs where you failed to write data or discs where session close processing
has not been made - these discs cannot be used.
(4) Theoperationsmaynotstartor the data may not be read out under the following conditions:
The quality of the recorded signal has deteriorated due to the dirt or scratches on the
disc, or frequently rewrote discs.
If you fail to start the operation, take out the disc and reinsert it to try again to start.
÷Correspondence to Kodak Photo CD (single and multisession)
÷Conforming to MPC-3 specifications
÷Half-height size
÷Slot in loading
÷Windows 95 and Windows 98 (Plug and Play) supported
*Windows is a trademark of Microsoft Corporation.
Precautions on plying CD singles (8 cm Discs)
(1) When playing CD singles (8 cm discs), always use the adapter for 8 cm discs. Before loading
the disc into the CD-ROM drive unit, be sure to check that it is secured properly by the
catches of the adapter. If discs have been inserted without the adapter by mistake, remove
the disc immediately by pressing the eject button. If the disc does not come out with one
press, press another time.
(2) Use 8 cm disc adapters labeled with the
'
mark (recommended standard product). Do
not use adapters which cause the disc to idle, nor adapters which are bent or curved.
<DRC1085>
En
7
A HARDWARE TOUR
1Disc loading slot
Insert the CD-ROM with the label facing up.
When using 8 cm discs, attach a CD adapter (available at stores) to the disc, and
insert the disc into the disc loading slot.
2Stop (7)/Eject (0) button
This button is used to eject the disc. When this button is pressed once during
playback of an audio disc, the playback will be stopped, and when it is pressed in
stopped condition, the disc will be ejected.
3Play (3)/Skip (¢) button
This is used for direct playback of audio discs. When an audio disc is inserted and
this button is pressed, play status will be reached, and when this button is pressed
in play status, the playback will skip to the next track. Data discs will not be played
back.
4BUSY indicator
This flashes during data access.
5Volume Control (headphone level)
This is used to adjust the volume level of the headphone jack.
6Headphone jack (PHONES)
This is a stereo minijack for headphones.
Fig. 1
Illustrations are provided in this chapter as a visual introduction to the Drive.
Please Familiarize yourself with these illustrations and refer to them when necessary
to complete the installation and operation of the unit.
BUSYPHONES
6 5 4
1
CD-ROM DRIVE
23
FRONT VIEW
8
<DRC1085>
En
7DC Input
This is the power supply input for DC +5 V and +12 V.
A HARDWARE TOUR
REAR VIEW
Fig. 2
1
2
39
401145
21
- 0 9 8 7
41
Pin Name Function
1 +12 Power supply input for DC +12 V.
2 G Ground.
3 G Ground.
4 +5 Power supply input for DC +5 V.
Pin Name Function
1 L Left channel audio output.
2 G Ground.
3 G Ground.
4 R Right channel audio output.
Pin Name Function
1 GND Ground.
2 Digital Out Digital audio signal output.
8Host IDE Interface
This is a 40 pin I/O connector according to the ATA specifications.
9Device Configuration Jumper
This is the jumper switch for selection of the drive use mode and supporting PC.
Short-circuit socket is attached for the setting
attached : on not attached : off
* Only MASTER is ON at the time of shipping from the plant.
0Audio Output
This is a connector for output of analog audio.
As a Molex 70553 type connecter is used, select a matching connection cable.
-Digital Audio Output
This is a connector for output of digital audio signal.
Pin Name Function
1 MASTER* on The drive is used in master mode.
2 SLAVE on The drive is used in slave mode.
3 CABLE on Mode for drive setting by CABLE
SELECT SELECT of the IDE interface.
4 Reserved.
5 Reserved.
<DRC1085>
En
9
TO INSTALL THE DRIVE
÷Switch off the power of the personal computer and remove the cover or the front
panel.
÷Remove the blank panel installed at the front of the 5.25 inch slot.
Installation is not possible when there is no empty slot.
÷Install the fixation slide rails on the drive. (If slide rails are required, contact the
shop where you bought the computer or the computer manufacturer.)
÷Insert the drive into the slot.
÷Iffixing is required,fixthedriveaccordingto the instruction manual for the computer.
Fig. 3
BUSY
PHONES
CD-ROM DRIVE
Use mounting screws with a length of 5 mm (3/16 in.) or less.
Use of long screws may damage the drive.
Install the drive after the power supply of the personal computer has
been switched off.
When the mounting screws are loose etc., the vibrations from disc
rotation can generate a ripping noise, so that the screws should be
tightened securely.
The drive installation method differs according to the computer type.
For details, please refer to the manuals of your computer.
10
<DRC1085>
En
CONNECTION
÷Switch off the power supply of the personal computer.
÷Connect the power supply cable from the personal computer. At the time of
connection, please pay attention to the cable polarity.
÷Connect the IDE interface cable. At this time, confirm that the pin 1 of the IDE
connector is connected correctly to pin 1 of the cable.
÷When a sound board is used, connect the audio output with an audio cable to the
sound board.
IDE Interface cable Power cable
Audio Cable
Fig. 4
Pin 1
Digital Audio Output
WARNING
The power supply of the personal computer always must be switched
off before cables are connected.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Idiomas:
Otros manuales de Unidad de CD/CDR de Pioneer
Pioneer
Pioneer BDR-S13E-X Manual de usuario
Pioneer
Pioneer DVR-111D Manual de usuario
Pioneer
Pioneer BDR-XS07UHD Manual de usuario
Pioneer
Pioneer DVR-104 Manual de usuario
Pioneer
Pioneer DVR-A05 Manual de usuario
Pioneer
Pioneer BDR-XD08B Manual de usuario
Pioneer
Pioneer DVR-S201 Manual de usuario
Pioneer
Pioneer DR-506S Manual de usuario
Pioneer
Pioneer BDR-X13EBK Manual de usuario
Pioneer
Pioneer BDR-XD08UMB-S Manual de usuario
Pioneer
Pioneer DR-U124X-1 Manual de usuario
Pioneer
Pioneer DR-706S Manual de usuario
Pioneer
Pioneer BDR-207EBK Manual de usuario
Pioneer
Pioneer DR-504S Manual de usuario
Pioneer
Pioneer DR-R102 Manual de usuario
Pioneer
Pioneer DR-U104X Manual de usuario
Pioneer
Pioneer DVR-SK12D Manual de usuario
Pioneer
Pioneer DVR-112 Manual de usuario
Pioneer
Pioneer BDR-XS07TUHD Manual de usuario
Pioneer
Pioneer BDR-S13UBK Manual de usuario
Manuales populares de Unidad de CD/CDR de otras marcas
SmartDisk
SmartDisk Firewire CD-R/W Manual de usuario
Axis
Axis CD-ROM SERVER Manual de usuario
LG
LG CRD-8322B Manual de usuario
Memorex
Memorex 32023234 - 52x32x52x External USB2.0 CD... Instrucciones de instalación
Yamaha
Yamaha CD Recordable/Rewritable Drive CRW3200 Manual de usuario
Sony
Sony CRX230AE Manual de usuario
