Pilz PSSu E S 4DO 0.5-D Manual de usuario
PSSu E S 4DO 0.5-(T)D
Operating Manual 21951-EN-07
}Decentralised system PSSuniversal I/O
Preface
This document is a translation of the original document.
All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made
for internal purposes. Suggestions and comments for improving this documentation will be
gratefully received.
Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,
SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks
of Pilz GmbH & Co. KG in some countries.
SD means Secure Digital
Contents
Operating Manual PSSu E S 4DO 0.5-(T)D
21951-EN-07 3
Section 1 Introduction 5
1.1 Validity of documentation 5
1.1.1 Retaining the documentation 5
1.1.2 Terminology: System environment A and B 5
1.2 Definition of symbols 6
Section 2 Overview 7
2.1 Module structure 7
2.2 Module features 7
2.3 Front view 8
Section 3 Safety 10
3.1 Intended use 10
3.2 Safety regulations 11
3.2.1 Use of qualified personnel 11
3.2.2 Warranty and liability 11
3.2.3 Disposal 11
Section 4 Function description 12
4.1 Block diagram 12
4.2 Module features 12
4.2.1 Functions 12
4.2.2 Integrated protection mechanisms 13
4.2.3 Reaction times 13
4.3 Configuration 14
4.3.1 PSSu assignment in system environment A 14
4.3.1.1 Addresses in the process image 14
4.3.1.2 Status byte 14
4.3.2 PSSu assignment in system environment B 15
Section 5 Installation 16
5.1 General installation guidelines 16
5.1.1 Dimensions 16
5.2 Installing the base module 18
5.3 Inserting and removing an electronic module 19
5.3.1 Inserting an electronic module 20
5.3.2 Removing an electronic module 21
5.3.3 Changing an electronic module during operation 21
Section 6 Wiring 22
6.1 General wiring guidelines 22
6.1.1 Mechanical connection of the base modules 22
6.2 Terminal configuration 24
6.3 Connecting the module 26
Section 7 Operation 27
7.1 Messages 27
Contents
Operating Manual PSSu E S 4DO 0.5-(T)D
21951-EN-07 4
7.2 Display elements 28
7.2.1 Display elements for module diagnostics 28
7.2.2 Display elements for output status 28
Section 8 Technical details 29
Section 9 Order reference 32
9.1 Product 32
9.2 Accessories 32
Introduction
Operating Manual PSSu E S 4DO 0.5-(T)D
21951-EN-07 5
1 Introduction
1.1 Validity of documentation
This documentation is valid for the products PSSu E S 4DO 0.5-D and PSSu E S 4DO 0.5-
TD. It is valid until new documentation is published.
This operating manual explains the function and operation, describes the installation and
provides guidelines on how to connect the product.
The module PSSu E S 4DO 0.5-TD is suitable for use where there are increased environ-
mental requirements (see Technical Details).
1.1.1 Retaining the documentation
This documentation is intended for instruction and should be retained for future reference.
1.1.2 Terminology: System environment A and B
The PSSu system can be used in two different system environments. The module's applic-
ation area is described in the chapter "Intended Use" of the manual.
The distinction is made between
}PSSu in system environment A
}PSSu in system environment B
The distinction is based on the application area of the PSSu system.
PSSu in system environment A may be used in the
}Decentralised system PSSu I/O
}Not in the automation system PSS 4000
PSSu in system environment B may be used in the
}Automation system PSS 4000, e.g. with
– Decentralised system PSSu I/O with SafetyNET p
– Control system PSSu PLC
– Control system PSSu multi
Introduction
Operating Manual PSSu E S 4DO 0.5-(T)D
21951-EN-07 6
1.2 Definition of symbols
Information that is particularly important is identified as follows:
DANGER!
This warning must be heeded! It warns of a hazardous situation that poses
an immediate threat of serious injury and death and indicates preventive
measures that can be taken.
WARNING!
This warning must be heeded! It warns of a hazardous situation that could
lead to serious injury and death and indicates preventive measures that can
be taken.
CAUTION!
This refers to a hazard that can lead to a less serious or minor injury plus
material damage, and also provides information on preventive measures
that can be taken.
NOTICE
This describes a situation in which the product or devices could be dam-
aged and also provides information on preventive measures that can be
taken. It also highlights areas within the text that are of particular import-
ance.
INFORMATION
This gives advice on applications and provides information on special fea-
tures.
Overview
Operating Manual PSSu E S 4DO 0.5-(T)D
21951-EN-07 7
2 Overview
2.1 Module structure
A module consists of
}Electronic module and
}Base module with
– Screw terminals or
– Cage clamp terminals
The base modules are the carrier units for the electronic modules and are used to connect
the field wiring. The electronic modules are inserted on to the base modules and determine
the module's function.
Details of the base modules that can be used are available in the chapter entitled “Intended
Use”.
2.2 Module features
The product has the following features:
}4 Digital outputs
– Semiconductor technology
– Single-pole
– Positive-switching
– Current load capacity per output: 0,50 A
– Short circuit-proof
– Overload-proof
}LEDs for:
– Switch status of each output
– Module error
}The module provides advanced diagnostic data.
}Optional access to the advanced diagnostic data in the process image (system environ-
ment A only)
}For standard applications in system environment A and B
}T-type:
PSSu E S 4DO 0.5-TD: for increased environmental requirements
Overview
Operating Manual PSSu E S 4DO 0.5-(T)D
21951-EN-07 8
2.3 Front view
2111
2212
2313
2414
Err
11
O0
21
O1
12
0V
22
0V
13
(C)
23
(C)
14
O2
24
O3
PSSu E S
4DO0.5-D
11
14
21
24
PSSu E S
4DO 0.5-D
312406
000000
001
10
1
3
4
9
8
5
6
7
11
2
12
A
B
Legend:
}A: Electronic module
}B: Base module
}1: LED for module diagnostics
}2: Labelling strip with:
– Name of electronic module
– Order number
– Serial number
– Hardware version number
– 2D code
}3: Labelling strip for the terminal configuration on the base module
}4: Status LEDs
}5: Name of electronic module
}6: Connection level 1
}7: Connection level 2
}8: Connection level 3
Overview
Operating Manual PSSu E S 4DO 0.5-(T)D
21951-EN-07 9
}9: Connection level 4
}10: Square mounting holes (connection levels 1, 2, 3 and 4)
– With screw to loosen/tighten the screw terminal on base modules with screw termin-
als
– With mechanism to operate the cage clamp on base modules with cage clamp ter-
minals
}11: Round connection holes (connection levels 1, 2, 3 and 4) for connecting the signal
lines
}12: Mounting slot for colour marker to label the connection level (connection levels 1, 2,
3 and 4)
Safety
Operating Manual PSSu E S 4DO 0.5-(T)D
21951-EN-07 10
3 Safety
3.1 Intended use
The module may be used for standard applications in system environment A and B.
The module provides type 1 outputs in accordance with IEC 61131-2. It may be used to
switch:
}Resistive loads
}Inductive loads
}Capacitive loads
The module PSSu E S 4DO 0.5-TD is suitable for use where there are increased environ-
mental requirements (see Technical Details).
Intended use includes making the electrical installation EMC-compliant. Please refer to the
guidelines stated in the "PSSuniversal Installation Manual". The module is designed for use
in an industrial environment. It is not suitable for use in a domestic environment, as this can
lead to interference.
The following is deemed improper use in particular:
}Any component, technical or electrical modification to the module
}Use of the module outside the areas described in this manual
}Any use of the module that is not in accordance with the technical details.
INFORMATION
The module is supported by:
}PSSuniversal Configurator and PSSuniversal Assistant from Version
1.6.0
}PAS4000 from version 1.8.0
– We recommend that you always use the latest version (download
from www.pilz.de).
The PSSu E S 4DO 0.5-D module may be used in conjunction with the following base mod-
ules:
}PSSu BP 1/8 S
}PSSu BP 1/8 C
}PSSu BP-C 1/8 S
}PSSu BP-C 1/8 C
}PSSu BP 1/12 S
}PSSu BP 1/12 C
}PSSu BP-C1 1/12 S
}PSSu BP-C1 1/12 C
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Sistema de E/S de Pilz
Pilz
Pilz PSS u2 ES 4DOD 0.5A Manual de usuario
Pilz
Pilz PSS u2 ES 8DID Manual de usuario
Pilz
Pilz PSSu K S 8DI 8DO 0.5 Manual de usuario
Pilz
Pilz PSSu E F BSW Manual de usuario
Pilz
Pilz PSS u2 EF 2DO R 8A Manual de usuario
Pilz
Pilz PSSu E S 4AO U Manual de usuario
Pilz
Pilz PSSu H F PN o Manual de usuario
Pilz
Pilz PSSu H SB-T Manual de usuario
Pilz
Pilz PSS u2 ES 16PT 0V Manual de usuario
Pilz
Pilz PSSu E PS-P +/-10V Manual de usuario
Pilz
Pilz PSSu E S 2AI U Manual de usuario
Pilz
Pilz PDP67 F 8DI ION HP Manual de usuario
Pilz
Pilz PSS u2 ES 4DOD 2A Manual de usuario
Pilz
Pilz PSSu K S RS232 Modbus ASCII Manual de usuario
Pilz
Pilz PNOZ msi9p Manual de usuario
Pilz
Pilz PSSu E S 2AO I Manual de usuario
Pilz
Pilz PNOZ m EF 4AI Manual de usuario
Pilz
Pilz PSS u2 P0 F/S EIP Manual de usuario
Pilz
Pilz PSS u2 ES 8DOD 0.5A Manual de usuario
Pilz
Pilz PSS u2 ES 16DI Manual de usuario
Manuales populares de Sistema de E/S de otras marcas
WAGO
WAGO 750-344 Manual de usuario
Teknim
Teknim TWM-1887 Manual de instrucciones
Intelligent Appliance
Intelligent Appliance IA-2662-E Manual de usuario
BERGHOF
BERGHOF ECC DIO 16/16 Manual de instrucciones
Advantech
Advantech PCM-27J3AU Manual de instalación y operación
Festo
Festo CP-E08-M12-CL Manual de usuario
