Pickering 42-204 Manual de usuario

pickeringtest.com

Issue 1.3 May 2022

40/42-204 User Manual

PXI/PXIe 1000Base-T1 Dual MUX With Fault Insertion

Page (II) PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204

pickering

Page (II) REED RELAY MODULE 40-110/115/120/125

pickering

No part of this publication may be reproduced, transmitted, transcribed, translated or stored in any form, or by

any means without the written permission of Pickering Interfaces.

Technical details contained within this publication are subject to change without notice.

ISO 9001

Reg No. FM38792

Page (III)

PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204

pickering

Page (III)

REED RELAY MODULE 40-110/115/120/125

pickering

TECHNICAL SUPPORT

For Technical Support please contact Pickering Interfaces either by phone, the website or via e-mail.

WARRANTY

All products manufactured by Pickering Interfaces are warranted against defective materials and workmanship for a period of

three years, excluding programmable power supplies, from the date of delivery to the original purchaser. Any product found to be

defective within this period will, at the discretion of Pickering Interfaces be repaired or replaced.

Products serviced and repaired outside of the warranty period are warranted for ninety days.

Extended warranty and service are available. Please contact Pickering Interfaces by phone, the website or via e-mail.

ENVIRONMENTAL POLICY

Pickering Interfaces operates under an environmental management system similar to ISO 14001.

Pickering Interfaces strives to full all relevant environmental laws and regulations and reduce wastes and releases to the

environment. Pickering Interfaces aims to design and operate products in a way that protects the environment and the health and

safety of its employees, customers and the public. Pickering Interfaces endeavours to develop and manufacture products that can

be produced, distributed, used and recycled, or disposed of, in a safe and environmentally friendly manner.

Worldwide Technical Support and Product Information

pickeringtest.com

Germany

Tel: +49 89 125 953 160

E-mail: [email protected]

Sweden

Tel: +46 340-69 06 69

E-mail: [email protected]

USA

Tel: (West) +1 541 471 0700

Tel: (East) +1 781 897 1710

E-mail: [email protected]

Czech Republic

Tel: +420 558 987 613

E-mail: [email protected]

France

Tel +33 9 72 58 77 00

E-mail [email protected]

Pickering Interfaces Headquarters

Stephenson Road Clacton-on-Sea CO15 4NL United Kingdom

Tel: +44 (0)1255-687900

E-Mail: [email protected]

China

Tel: +86 4008 799 765

E-mail: [email protected]

Page (IV) PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204

pickering

Page (IV) REED RELAY MODULE 40-110/115/120/125

pickering

MEANING / DESCRIPTION SYMBOL

PROTECTIVE EARTH (GROUND)

To identify any terminal which is intended for connection to an external conductor for

protection against electric shock in case of a fault, or the terminal of a protective earth

(ground) electrode.

DANGEROUS VOLTAGE

To indicate hazards arising from dangerous voltages.

WARNING / CAUTION

An appropriate safety instruction should be followed or caution to a potential hazard

exists.

Refer to the relevant instructions detailed within the product manual.

HEAVY

If this product is heavy reference should be made to the safety instructions for

provisions of lifting and moving.

STATIC SENSITIVE

To indicate that static sensitive devices are present and handling precautions should

be followed.

SAFETY SYMBOLS

PRODUCT SAFETY

The following safety symbols may be used on the product and throughout the product documentation.

Page (V)

PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204

pickering

Technical Support and Warranty................................................III

Product Safety .............................................................................IV

Contents (this page)....................................................................V

Warnings and Cautions ..............................................................VII

Section 1

Technical Specication...............................................................1.1

Section 2

Technical Description .................................................................2.1

Functional Description..........................................................2.1

Multiplexer Ground................................................................2.1

Section 3

Installation....................................................................................3.1

Pre Operation Checks...........................................................3.1

Hardware Installation ............................................................3.2

Software Installation .............................................................3.2

Testing Operation ..................................................................3.3

Section 4

Programming Guide....................................................................4.1

Programming Options For PXI/PXIe Modules.....................4.1

Module Architecture..............................................................4.2

Programming The Module ....................................................4.3

Section 5

Connector Information................................................................5.1

Section 6

Trouble Shooting .........................................................................6.1

Section 7

Maintenance Information............................................................7.1

Relay Lookup Table...............................................................7.2

CONTENTS

Page (VI) PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204

pickering

THIS PAGE INTENTIONALLY BLANK

Page (VII)

PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204

pickering

Page (VII)

2 AMP 1-POLE UHD MATRIX MODULES 40-575 / 576 / 577 / 578 / 579

pickering

WARNINGS AND CAUTIONS

WARNING - HAZARDOUS ENVIRONMENTS SYMBOL

This product is not specically designed for use in hazardous environments, for example in explosive

atmospheres. If the product is to be used in hazardous environments we recommend that the user

ensures suitable protective measures are taken.

WARNING - DANGER OF ELECTRIC SHOCK SYMBOL

This module may contain hazardous voltages. Before removing the module from the rack remove all

supplies and disconnect user I/O signals.

Unused slots in the host chassis are populated with blanking plates to prevent access to user I/O

signals that may be present. Blanking panels are available to order from Pickering in a variety of

slot widths. If the product is not used in this manner for example by using an extender card then

additional care must be taken to avoid contact with exposed signals.

Not to be used in safety critical circuits, refer to the Pickering Interfaces’ terms & conditions of sale.

This module must not be used for the switching of Mains Circuits. For the switching of voltages up

to the module’s full specication, Secondary Circuit power supplies and the Device Under Test must

be fully isolated from the Mains Circuit and the safety earth.

The host chassis must be correctly installed and be connected to mains or factory safety ground,

please refer to your chassis installation manual.

Diagram Showing Separation Between The Mains Circuit and Secondary Circuit / DUT

For the purposes of this document, a Mains Circuit is an installation classied as Overvoltage

Category II up to 300V. Separation between the Secondary Circuit and Mains Circuit is achieved

by a transformer in which the primary windings are separated from the secondary windings by

reinforced insulation, double insulation, or a screen connected to the protective conductor terminal.

CAUTION - HANDLING OF ELECTROSTATIC-SENSITIVE DEVICES SYMBOL

Certain semiconductor devices used in this equipment are liable to damage due to static voltage.

Observe the following precautions when handling these devices in their unterminated state, or

sub-assemblies containing these devices:

1. Persons removing sub-assemblies from equipment using these devices must be earthed by a

wrist strap and a resistor at the point provided on the equipment.

2. Soldering irons used during the repair operations must be low voltage types with earthed tips and

isolated from the mains voltage by a double insulated transformer.

3. Outer clothing worn must be unable to generate static charges.

4. Printed Circuit Boards (PCBs) tted with these devices must be stored and transported in

anti-static bags.

PXI Switching

Module

Device

Under Test

Power

Supply

Power

Supply

Host Chassis

Secondary Circuit

Mains

Circuit

Mains

Circuit

Mains/Factory

Safety Ground

Page (VIII) PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204

pickering

Page (VIII) 2 AMP 1-POLE UHD MATRIX MODULES 40-575 / 576 / 577 / 578 / 579

pickering

CAUTION - PRODUCT DOCUMENTATION SYMBOL

Suitably qualied & trained users should ensure that the accompanying documentation is fully read

and understood before attempting to install or operate the product.

SAFETY INSTRUCTIONS

All cleaning and servicing requires the equipment to be isolated and disconnected from the power source and user I/O

signals (refer to the Maintenance Section).

• Appropriate manual handling procedures should be followed as dictated by the weight of the individual module or

the combined weight of the modules & chassis.

• Should a fault occur with the module or chassis, immediately isolate and disconnect the incoming power to the

chassis and the user I/O signals.

• Ensure the equipment is installed, operated and maintained by trained and authorised personnel.

• For suitably equipped products in the event of an emergency press the red “emergency stop” button situated on

the front of the unit.

Page 1.1

PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204

pickering SECTION 1 - TECHNICAL SPECIFICATION

SECTION 1 - TECHNICAL SPECIFICATION

pickeringtest.com

PXI/PXIe 1000Base-T1 Dual MUX With Fault Insertion 40/42-204

ISSUE 1.3 MAY 2022

yAvailable as PXI or PXIe Modules

ySuited for 1000Base-T1/100Base-T1 Switching

yFault Insertion on 1 or 2 Channels of 2 Wire

Connections

yDual MUX for External Systems

yControlled Transmission Line Impedance

ySimple Insertion of Shorted Pair, Open and

Battery/Ground Connection

yVISA, IVI & Kernel Drivers Supplied for

Windows

ySupported by PXI or LXI Chassis

y3 Year Warranty

Fault Connections

FB1 FB2

M+

M-

M-LOOP+

M-LOOP-

U+

U-

U-LOOP+

U-LOOP-

40/42-204-001 Single Channel 1000Base-T1

Fault Insertion Switch Schematic Diagram

The 40-204 (PXI) and 42-204 (PXIe) are designed

to simulate common faults on high-speed two wire

communication interfaces such as 1000Base-T1. They

support 1 or 2-channels of two wire serial interfaces. Each

channel pair can be looped out to external equipment or

the switches can be used simulate a channel open fault.

Using the fault bus, switches can simulate a short between

both wires or a short to one of two externally applied fault

conditions – such as battery supply or ground - via two

fault buses.

Each channel can carry up to 0.8 A and is rated up to 200 V

between wire pairs. The wire pairs have controlled

transmission line impedance suited to most differential

Pickering’s Range of Fault Insertion Switches

Model No. Signal

Channels

Fault

Buses

Fault

Inputs

Max

Voltage

Max Current

or Bus Type

40-190B 74, 64 or 32 1 or 2 4 or 8 165 V 2 A

40-191A 6 2 2 40 V 30 A

40-192 6 2 2 200 V 10 A

40-193 7 1 or 2 1 or 2 16 V 20 A, 1 A min

40-194 7 1 or 2 1 or 2 16 V 20 A, no min

40-195 22 or 11 pairs — 8 or 4 150 V 1 A

40-196 10 or 5 pairs — 10 or 5 110 V 5 A

40-197A 34 or 16 4 8 300 V 2 A

40-198 20 1 or 2 3 or 6 250 V 5 A

40-199 10 1 or 2 2 250 V 10 A

40-200 4 or 8

differential 4 8 100 V CAN, FlexRay

40-201 4 or 8

differential 2 4 100 V Ethernet/AFDX

/BroadR-Reach

40-202 22 or 11 pairs — 22 or 11 150 V 1 A

40/42-204 1 or 2

differential 2 2 200 V 1000Base-T1

signalling systems, including high-speed 1000Base-T1,

the fault buses are capable of carrying 0.8 A and also

have controlled transmission line impedance. The front

panel signal connectors are easy to use MMCX which are

fully supported by our range of connector accessories.

The module uses high quality electro-mechanical relays

designed for high frequency application with long service

life.

Differential Bus Switching

We also offer the 40-736 and 40-737 multiplexers which

are suitable for switching Ethernet, USB and other serial

communications signals.

Page 1.2 PXI/PXIe 1000BASE-T1 DUAL MUX WITH FAULT INSERTION 40/42-204

pickering

SECTION 1 - TECHNICAL SPECIFICATION

1000Base-T1 Dual MUX, 40/42-204

pickeringtest.com

Speciﬁcations

Power Requirements - 40-204

+3.3 V +5 V +12 V -12 V

0.03 A 0.3 A 0 0

Power Requirements - 42-204

+3.3 V +12 V

0.03 A 0.15 A

Operating/Storage Conditions

Operating Conditions

Operating Temperature:

Humidity:

Altitude:

0 °C to +55 °C

Up to 90 % non-condensing

5000 m

Storage and Transport Conditions

Storage Temperature:

Humidity:

Altitude:

-20 °C to +75 °C

Up to 90 % non-condensing

15000 m

PXI & CompactPCI Compliance - 40-204

The module is compliant with the PXI Speciﬁcation 2.2.

Local Bus, Trigger Bus & Star Trigger are not implemented.

Uses a 33 MHz 32-bit backplane interface.

PXIe Compliance - 42-204

The module is compliant with the PXIe Speciﬁcation 1.0.

Local Bus, Trigger Bus & Star Trigger are not implemented.

Safety & CE Compliance

All modules are fully CE compliant and meet applicable

EU directives: Low-voltage safety EN61010-1:2010,

EMC Immunity EN61326-1:2013,

Emissions EN55011:2009+A1:2010.

Mechanical Characteristics

40-204 - Single slot 3U PXI (CompactPCI card).

42-204 - Single slot 3U PXIe, compatible with PXIe hybrid

slot.

Module weight: 210g

3D models for all versions in a variety of popular ﬁle

formats are available on request.

Connectors

40-204 - PXI bus via 32-bit P1/J1 backplane connector.

42-204 - PXIe bus via XJ3 and XJ4 backplane connectors.

Signals via front panel mounted MMCX coaxial connectors.

Speciﬁcation

Conﬁguration: 1 or 2-pairs of two wire connections

designed for use on differential

serial interfaces with multiplexers

for connection to external

equipment.

Faults Simulated: Open on wire pairs or loop out to

external fault system via 2 fault

buses (for dual versions, the fault

buses for each bank are isolated

from each other).

Ground Connection: Each multiplexer bank has isolated

ground planes that are directly

connected to the outer of the front

panel connectors.

Differential Line

Impedance:

100 Ω

Fault Bus

Impedance:

50 Ω

Voltage Rating:

Carry Current

Rating:

Max Hot Switch

Current:

200 V*

0.8 A

0.5 A

Path Resistance: <1 Ω

Typical Bandwidth: >700 MHz Differential

Operate Time: 0.5 ms

* For full voltage rating, signal sources to be switched

must be fully isolated from mains supply and safety earth.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Multiplexor de Pickering

Pickering

Pickering 40-666 Manual de usuario

Pickering

Pickering 4-788 Series Manual de usuario

Pickering

Pickering PXI 40-740 Manual de usuario

Pickering

Pickering 40-667B Manual de usuario

Pickering

Pickering PXI 40-635A Manual de usuario

Pickering

Pickering 40-619 Manual de usuario

Pickering

Pickering 40-666A Manual de usuario

Pickering

Pickering 40-657A Manual de usuario

Pickering

Pickering LXI 60-802 Manual de usuario

Pickering

Pickering 40-760 Manual de usuario

Pickering

Pickering 40-666B Manual de usuario

Pickering

Pickering PXI 40-660 Manual de usuario

Pickering

Pickering 40-570A Manual de usuario

Pickering

Pickering SYSTEM 10 Manual de usuario

Pickering

Pickering 4 878 Series Manual de usuario

Pickering

Pickering 40-640 Manual de usuario

Pickering

Pickering PXI 40-882B Manual de usuario

Pickering

Pickering 20-745 Manual de usuario

Pickering

Pickering PXI 40-850A Manual de usuario

Pickering

Pickering 40-610A Manual de usuario

Pickering

Pickering 40-660A-001 Manual de usuario

Pickering

Pickering 40-680 Manual de usuario

Pickering

Pickering 40-655A Manual de usuario

Pickering

Pickering 60-850 Manual de usuario

Manuales populares de Multiplexor de otras marcas

Campbell

Campbell AM416 Manual de usuario

Paradyne

Paradyne SIM2000 Manual de usuario

Panasonic

Panasonic WJFS616 - SWITCHER Manual de usuario

Lanex

Lanex TM-77 Manual de usuario

Bosch

Bosch VSS8394/01T Manual de usuario

Quark-Elec

Quark-Elec QK-A035 Manual de usuario

ADTRAN

ADTRAN Frameport 768 Manual de usuario

Elo TouchSystems

Elo TouchSystems E247 Manual de usuario

Paradyne

Paradyne Hotwire 8786 Manual de usuario

RFL Electronics

RFL Electronics 9508D UCC Manual de usuario

Miranda

Miranda AMX-101i Manual de instrucciones

ShipModul

ShipModul MiniPlex-AIX NMEA-0183 Manual de usuario

GE StoreSafe SDVR-10 Manual de usuario

American Fibertek

American Fibertek MTX-8410C Manual de usuario

ADC

ADC HiGain ELU-319 5E Manual de usuario

Paradyne

Paradyne Hotwire 8774 Manual de usuario

American Fibertek

American Fibertek MTX-8810C-SL Manual de usuario

Viessmann

Viessmann 5229 Manual de usuario