Phoenix Gold The One Limited Edition Amplifier Manual de usuario

Amplifier Manual

Features:

• Limited Edition Production Run featuring each unit number laser cut into the heatsink

• Six Massive Unregulated Power Supplies with Hand Wound Transformers

• Three Ounce Gold Plated Circuit Board

• High Eciency Class D Topology that operates at up to 16 volts

• Three 1/0 Gauge Direct Insert Power Terminals

• Temperature Controlled Fan Cooling System

• 24dB Variable Low Pass and Subsonic Crossovers

• Two units are “strappable” or linkable for insane power into a single subwoofer

• Hand Crafted Wood Shipping Crate

• LPL44 - Low Pass Level Control Ready

• RMD - Remote Monitoring Display Port

The One

Limited Edition Amplifier

Serial# ___________

QC Tested By: ____________________________

QC TEST DATE: ____________________________

Amplier Owner’s Manual

Owner’s Name:

Serial Number:

Purchase Location:

Purchase Date:

Installer:

Owner Information

INTRODUCTION

The One is a truly unique amplier that follows in the legendary footsteps of Limited Edition ampliers from Phoenix

Gold. While the external function of this monoblock amplier is fairly simple its very important to respect the immense

amount of power it can produce. Be sure the proper subwoofers are selected as this amplier will easily damage low to

mid powered subwoofers. Phoenix Gold is not responsible for speaker failures or damage.

Phoenix Gold has taken special care to make sure each amplier is of the highest quality possible. After the electrical

components are pre-tested and inserted into the circuit boards then each amplier is carefully hand assembled one

by one. Once assembled the ampliers are rigorously tested. The rst testing stage is performed by a state of art Audio

Precision computerized program. Specically designed by the Phoenix Gold engineering team, this testing program

is powerful and complex. It immediately and accurately measures distortion levels, power output, crossover functions

and numerous other specications.

Once the amplier has passed the Audio Precision testing, its then ‘burned in’for a minimum of two hours to verify all

part temperatures are within specication and all systems are working properly. After the unit passes burn in, it is then

retested with the Audio Precision again to verify it still meets the original testing criteria. Once it passes this test for a

second time it then undergoes a nal visible inspection and human listening test. Rest assured this amplier has been

fully tested before its laid to rest in its custom made wood crate.

As mentioned throughout this manual, the proper electrical system is REQUIRED not optional. The amplier can be

damaged and will not reach its full potential without the proper electrical system. Stinger accessories and power wiring

are heavily recommended due to their high quality. For example, Stinger power wire is 100% OFC copper and adheres

to a Tru-Spec wire gauge standard. Many low quality power wires may look like 1/0 gauge from the outer jacket, but the

internal copper is actually closer to 4 gauge to save costs. Also do not use CCAW or Copper Clad Aluminum Wire as it

does not conduct current as well as copper.

Congratulations on purchasing the most powerful and one of the rarest ampliers ever built by Phoenix Gold. Be sure

to keep all of the documentation, certicate of authenticity and shipping crate as this amplier is truly a collector’s

dream.

Amplier Owner’s Manual

Electrical Breakdown

Temperature controlled

fan cooling system

Sealed high quality alumi-

num shaft potentiometers

Six massive unregulated

power supplies with hand

wound transformers

3 Ounce Gold Plated Circuit Board

50 200 volt/1000uF rail voltage

capacitors can power a small city

47 35 volt/1200uF capacitors

stien the power supply during

massive bass notes

13 grams per millimeter

of high density aluminum

heatsink

36 IRFP1405 power supply

transistors, just one of these is

capable of switching 70 amps

of current

32 FDA24N40F 400 volt

ultra fast output transistors 8 gauge Stinger HPM speaker

wire carries the high voltage/

high current signal directly to

the speaker outputs

5mm thick acrylic top is

heat and crack resistant

3mm thick high current

custom made buss bars Three high current 1/0 power

terminals are ready to pass up

to 900 amps continuously

State of the art Class D switch-

ing circuitry operates at an

amazing 90% eciency

Panel mount RCA connections

Each unit number is laser cut

into the heatsink so every

amplier is truly unique

Amplier Owner’s Manual

Measurements:

Frequency Response: ± 1dB from 20Hz to 300Hz

Signal to Noise Ratio: >90dB

Subsonic and Low Pass Crossovers: 24dB per octave

Low Pass Crossover Range: 30Hz to 300Hz

Subsonic Crossover Range: 10Hz to 55Hz

Bass Boost @ 45Hz: 0 to +6dB

Low Level Input Range: 200 millivolts to 8 volts

Lowest Recommend Load: 1 ohm

Lowest Recommend Strapped Load: 2 ohm

Typical Eciency: 90%

Damping Factor: Greater than 200

Recommended External Fusing: 250A x 3 (750A Total)

Minimum Power/Ground Wire Size: 1/0 Gauge x 3

Dimensions: 38.6” L x 12.2”W x 3.0” H

980mm x 310mm x 77mm

Power Output:

RMS Power 16.0Vdc 8000 x 1 @ 2 ohm

12000 x 1 @ 1 ohm

24000 x 1 @ 2 ohm (Strapped)

RMS Power 14.4Vdc 5000 x 1 @ 2 ohm

8000 x 1 @ 1 ohm

16000 x 1 @ 2 ohm (Strapped)

SPL “Burping” Power 16.0Vdc 10000 x 1 @ 2 ohm

18000 x 1 @ 1 ohm

36000 x 1 @ 2 ohm (Strapped)

Specifications

IMPORTANT PLEASE READ!

The One is an extremely high performance amplier. In order for it to reach its full potential,

the correct installation and wiring requirements MUST be followed. Please note the following:

• Do not touch the speaker wires or terminals while the amplier is on. This amplier has the

ability to cause serious injury due to electrocution.

• A high output alternator, at least three high capacity batteries and three separate runs of 1/0

power/ground wire are required for the electrical system.

• 1/0 Gauge wiring (or greater) is required for all power and ground connections.

• 8 Gauge wiring (or greater) is required for all speaker connections.

• All three of the power terminals must be wired to the electrical system. Using only one or

two of the terminals can damage the amplier.

Amplier Owner’s Manual

Power Output:

RMS Power 16.0Vdc 8000 x 1 @ 2 ohm

12000 x 1 @ 1 ohm

24000 x 1 @ 2 ohm (Strapped)

RMS Power 14.4Vdc 5000 x 1 @ 2 ohm

8000 x 1 @ 1 ohm

16000 x 1 @ 2 ohm (Strapped)

SPL “Burping” Power 16.0Vdc 10000 x 1 @ 2 ohm

18000 x 1 @ 1 ohm

36000 x 1 @ 2 ohm (Strapped)

INPUT

Connect preamp signal cables from the head unit to these terminals.

OUTPUT

Provides a full range signal for an additional amplier. There is no signal

loss if using this output.

LP FREQ

Controls the lowpass crossover point for the speaker outputs.

BASS BOOST

Variable bass boost from 0 to +6dB @ 45 Hz.

LOW PASS LEVEL CONTROL (LPL)

This port is for connecting the optional remote level control (LPL44).

This allows up to 20dB of volume adjustment. This is not a bass boost, it

controls the level of the low pass signal.

LEVEL

Used to reach maximum amplier power with a wide variety of headunits.

SPEAKER OUTPUTS

Used to connect the amplier to speakers. Minimum impedance is 1 ohm. 8 gauge

wire is required.

SUBSONIC

Controls the subsonic (highpass) crossover point for the speaker outputs to eliminate

extreme low frequencies.

PROTECT LED

Lights red if there is a problem with the audio system. For example, speaker wire is

pinched/shorted together or the amplier is running too low of an impedance.

INPUT SLAVE/OUTPUT MASTER SWITCH

For normal use, the switch MUST be set to “OUTPUT MASTER”. If linking or strapping

two ampliers together please see page 7 for more details. IMPORTANT: In normal or

single amplier use there will be no output if this switch is set to“INPUT SLAVE”. Be

sure it is set to“OUTPUT MASTER”.

+12V

This must be connected to the fused positive terminal (+12V) of the car’s battery. See

page 4 for an electrical system example. 1/0 gauge wire is required.

REMOTE

This must be connected to switched +12V, usually a trigger wire coming from the head

unit or ignition.

GND

This must be connected to the negative terminal of the car’s battery or bolted to a

clean, unpainted part of the chassis of the vehicle. 1/0 gauge wire is required.

COntrols

REMOTE MONITORING DISPLAY (RMD)

Connect optional RMD Voltage Display to this port.

IMPORTANT: ALL THREE POWER TERMINALS MUST

BE USED. DO NOT USE ONLY ONE OR TWO OF THE

TERMINALS, IT CAN DAMAGE THE AMPLIFIER.

Amplier Owner’s Manual

OUTPUT

MASTER

INPUT

SLAVE

SINGLE

CHANNEL

RCA

FROM

HEADUNIT

NOT

USED

Electrical system and wiring

200 Amp

High Output

Alternator

250 Amp Fuse located

within 18 inches of

the alternator

250 Amp Fuse located within

18 inches of the battery

250 Amp Fuse located within

18 inches of the battery

250 Amp Fuse located within

18 inches of the battery

250 Amp Fuse located within

18 inches of the battery

Three High Performance

Batteries with a 800 CCA

rating or larger

= 12 volt 1/0 Gauge Wire

= Ground 1/0 Gauge Wire

ALL THREE POWER TERMINALS MUST BE USED.

CAUTION: LAST POWER TERMINAL IS REVERSED.

The One requires a massive electrical system to power it correctly. The below system is the MINIMUM REQUIREMENT.

Each vehicle will vary so please contact your local dealer or Phoenix Gold for questions about the proper electrical

system before attempting installation.

*Batteries are located

within 48 inches of wire

length from the amplier

Amplier Owner’s Manual

How to strap two monoblocks

Strapping or linking two ampliers allows you to deliver a ton of power into a single voice coil commonly used in SPL

competitions. The example below shows two of “The Ones” delivering a total of 24,000 watts RMS into a single 2 ohm

voice coil.

• DO NOT STRAP AMPLIFIERS INTO A 1 OHM LOAD. Minimum load strapped is 2 ohm.

• The “Master” amplier’s preamp section controls both ampliers. “Slave”amplier’s pre-amp controls are disabled.

• The negative or (-) speaker output terminals are connected together using 8 gauge wire.

• CAUTION: This is an insane amount of power into a single voice coil. PG is not responsible for speaker failures or

damage.

OUTPUT

MASTER

INPUT

SLAVE

SINGLE

CHANNEL

RCA

FROM

HEADUNIT

NOT

USED

Slave amplier’s pre-amp section is disabled

Phoenix Gold

A Division of AAMP of America™

13190 56th Court

Clearwater, Florida 33760

P: 888-228-5560

[email protected]

www.phoenixgold.com

Designed and Engineered in the USA

Phoenix Gold Product Warranty

LIMITED WARRANTY ON AMPLIFIERS

Phoenix Gold warrants this product to be free of defects in materials and workmanship for a period of one (1) year from the original date of purchase. This

warranty is not transferable and applies only to the original purchaser from an authorized Phoenix Gold dealer in the United States of America only. Should service

be necessary under this warranty for any reason due to manufacturing defect or malfunction, Phoenix Gold will (at its discretion), repair or replace the defective

product with new or remanufactured product at no charge. Damage caused by the following is not covered under warranty: accident, misuse, abuse, product

modication or neglect, failure to follow installation instructions, unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover

incidental or consequential damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and

tear is not covered under warranty.

INTERNATIONAL WARRANTIES:

Products purchased outside the United States of America are covered only by that country’s Authorized Phoenix Gold reseller and not by Phoenix Gold. Consumers

needing service or warranty information for these products must contact that country’s reseller for information.

Tabla de contenidos

Otros manuales de Amplificador de Phoenix Gold

Phoenix Gold

Phoenix Gold Titanium 1000.2 Manual de usuario

Phoenix Gold

Phoenix Gold ZQ Series Manual de usuario

Phoenix Gold

Phoenix Gold R4.0:2 Manual de usuario

Phoenix Gold

Phoenix Gold Z Series Manual de usuario

Phoenix Gold

Phoenix Gold QZ900.1d Manual de usuario

Phoenix Gold

Phoenix Gold XS2300 blk Manual de usuario

Phoenix Gold

Phoenix Gold GX Series Manual de usuario

Phoenix Gold

Phoenix Gold XS4300 Manual de usuario

Phoenix Gold

Phoenix Gold MX1230 Manual de usuario

Phoenix Gold

Phoenix Gold MS275 Manual de usuario

Phoenix Gold

Phoenix Gold QX300.4 Manual de usuario

Phoenix Gold

Phoenix Gold RX2 1000.1 Manual de usuario

Phoenix Gold

Phoenix Gold MPS2500 Manual de usuario

Phoenix Gold

Phoenix Gold M50 Manual de usuario

Phoenix Gold

Phoenix Gold XS 2200 Manual de usuario

Phoenix Gold

Phoenix Gold m100 Manual de usuario

Phoenix Gold

Phoenix Gold R8.0:4 Manual de usuario

Phoenix Gold

Phoenix Gold Carver MP42 Manual de usuario

Phoenix Gold

Phoenix Gold RX2 750.5 Manual de usuario

Phoenix Gold

Phoenix Gold RSd250.2 Manual de usuario

Phoenix Gold

Phoenix Gold ZX450 Manual de usuario

Phoenix Gold

Phoenix Gold RSD250.2 Manual de usuario

Phoenix Gold

Phoenix Gold Ryval V8001 Manual de usuario

Phoenix Gold

Phoenix Gold iAmp Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario