Philips MC146/05 Manual de usuario

MC146

Micro Hi-Fi System

User manual

www.philips.com/welcome

MC146_05_UM_V2.0 2010.3.29, 15:501

Important notes for users in the

U.K.

Mains plug

This apparatus is fitted with an approved 13

Amp plug. To change a fuse in this type of plug

proceed as follows:

1Remove fuse cover and fuse.

2Fix new fuse which should be a BS1362 3 Amp,

A.S.T.A. or BSI approved type.

3Refit the fuse cover.

If the fitted plug is not suitable for your socket

outlets, it should be cut off and an appropriate

plug fitted in its place.

If the mains plug contains a fuse, this should

have a value of 3 Amp. If a plug without a fuse

is used, the fuse at the distribution board

should not be greater than 3 Amp.

Note: The severed plug must be disposed of to

avoid a possible shock hazard should it be

inserted into a 13 Amp socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured with

the following code: blue = neutral (N),

brown = live (L).

¶As these colours may not correspond with the

colour markings identifying the terminals in

your plug, proceed as follows:

–Connect the blue wire to the terminal

marked N or coloured black.

–Connect the brown wire to the terminal

marked L or coloured red.

–Do not connect either wire to the earth

terminal in the plug, marked E (or e) or

coloured green (or green and yellow).

Before replacing the plug cover, make certain

that the cord grip is clamped over the sheath

of the lead - not simply over the two wires.

Recording and playback of material may

require consent. See Copyright Act 1956 and

The Performer’s Protection Acts 1958 to 1972.

CAUTION

Use of controls or adjustments or

performance of procedures other than

herein may result in hazardous

radiation exposure or other unsafe

operation.

MC146_05_UM_V2.0 2010.3.29, 15:502

MICRO SYSTE M MC14 6

SOURC E

DBB

STANDBY-ON

VOL

TUNING

REPEAT PRO G

CD/CD -R/CD -RW COMPATIBL E

PRESE T

PULLTO OPEN

)

(

MC146_05_UM_V2.0 2010.3.29, 15:503

English

Contents

General Information

Supplied accessories ............................................ 5

Environmental Information ................................ 5

Safety Information ................................................ 5

Hearing Safety ....................................................... 6

Preparations

Rear connections ................................................. 7

Inserting batteries into the Remote Control ...

.................................................................................. 8

Using the Remote Control to operate the

system ..................................................................... 8

Controls

Controls on the system and remote control ...

.................................................................................. 9

Controls available on the remote control only

.................................................................................. 9

Basic Functions

Switching the system on ................................... 10

Power-saving automatic standby ..................... 10

Adjusting volume and sound ............................ 10

CD Operation

Loading a disc ...................................................... 11

Basic playback controls ..................................... 11

Different play modes: SHUFFLE and REPEAT ...

................................................................................ 12

Programming track numbers ........................... 12

Reviewing the programme ............................... 12

Erasing the programme ..................................... 12

Radio Reception

Tuning to radio stations .................................... 13

Programming radio stations ............................. 13

Automatic programming ......................................... 13

Manual programming ............................................... 13

Tuning to preset radio stations ....................... 13

Other Connection

Listening to an external source ...................... 14

Maintenance.............................................. 14

Clock/Timer

Setting the clock ................................................. 15

Setting the timer................................................. 15

Activating and deactivating TIMER ................. 15

Activating and deactivating SLEEP .................. 15

Specifications ........................................... 16

Tr oubleshooting ............................. 17~18

MC146_05_UM_V2.0 2010.3.29, 15:504

English

General Information

Congratulations on your purchase and welcome

to Philips!

To fully benefit from the support that Philips

offers, register your product at www.philips.com/

welcome.

This product complies with the radio

interference requirements of the European

Community.

Supplied accessories

–2speaker boxes

–remote control

Environmental Information

All unnecessary packaging has been omitted.We

have tried to make the packaging easy to

separate into three materials: cardboard (box),

polystyrene foam (buffer) and polyethylene (bags,

protective foam sheet).

Your system consists of materials which can be

recycled and reused if disassembled by a

specialized company. Please observe the local

regulations regarding the disposal of packaging

materials, exhausted batteries and old

equipment.

Safety Information

●Before operating the system, check that the

operating voltage indicated on the typeplate (or

the voltage indication beside the voltage

selector) of your system is identical with the

voltage of your local power supply. If not, please

consult your dealer.

●Place the system on a flat, hard and stable

surface.

●Where the MAINS plug or an appliance coupler

is used as the disconnet device, the disconnet

device shall remain readily operable.

●The apparatus shall not be exposed to

dripping or splashing.

●Install the unit near the AC outlet and where the

AC power plug can be easily reached.

●Place the system in a location with adequate

ventilation to prevent internal heat build-up in

your system. Allow at least 10 cm (4 inches)

clearance from the rear and the top of the unit

and 5 cm (2 inches) from each side.

●The ventilation should not be impeded by

covering the ventilation openings with items,

such as newspapers, table-cloths, curtains, etc.

●Do not expose the system, batteries or discs to

excessive moisture, rain, sand or heat sources

caused by heating equipment or direct sunlight.

●No naked flame sources, such as lighted candles,

should be placed on the apparatus.

●No objects filled with liquids, such as vases, shall

be placed on the apparatus.

●If the system is brought directly from a cold to a

warm location, or is placed in a very damp room,

moisture may condense on the lens of the disc

unit inside the system. Should this occur, the CD

player would not operate normally. Leave the

power on for about one hour with no disc in the

system until normal playback is possible.

●The mechanical parts of the set contain self-

lubricating bearings and must not be oiled or

lubricated.

●When the system is switched to Standby

mode, it is still consuming some power.

To disconnect the system from the

power supply completely, remove the AC

power plug from the wall socket.

MC146_05_UM_V2.0 2010.3.29, 15:505

English

General Information

Hearing Safety

Listen at a moderate volume.

●Using headphones at a high volume can impair

your hearing. This product can produce sounds

in decibel ranges that may cause hearing loss for

a normal person, even for exposure less than a

minute. The higher decibel ranges are offered

for those that may have already experienced

some hearing loss.

●Sound can be deceiving. Over time your hearing

"comfort level" adapts to higher volumes of

sound. So after prolonged listening, what sounds

"normal" can actually be loud and harmful to

your hearing. To guard against this, set your

volume to a safe level before your hearing

adapts and leave it there.

To establish a safe volume level:

●Set your volume control at a low setting.

●Slowly increase the sound until you can hear it

comfortably and clearly, without distortion.

Listen for reasonable periods of time:

●Prolonged exposure to sound, even at normally

"safe" levels, can also cause hearing loss.

●Be sure to use your equipment reasonably and

take appropriate breaks.

Be sure to observe the following

guidelines when using your headphones.

●Listen at reasonable volumes for reasonable

periods of time.

●Be careful not to adjust the volume as your

hearing adapts.

●Do not turn up the volume so high that you

can't hear what's around you.

●You should use caution or temporarily

discontinue use in potentially hazardous

situations.

●Do not use headphones while operating a

motorized vehicle, cycling, skateboarding, etc.; it

may create a traffic hazard and is illegal in many

areas.

Disposal of your old product

Your product is designed and

manufactured with high quality

materials and components,

which can be recycled and

reused.

When this crossed-out wheeled bin symbol is

attached to a product it means the product is

covered by the European Directive 2002/96/EC

Please inform yourself about the local separate

collection system for electrical and electronic

products.

Please act according to your local rules and do

not dispose of your old products with your

normal household waste.The correct disposal of

your old product will help prevent potential

negative consequences for the environment and

human health.

MC146_05_UM_V2.0 2010.3.29, 15:506

English

Preparations

Rear connections

The type plate is located at the rear of the

system.

For users in the U.K.: please follow the

instructions on page 2.

APower

–Before connecting the AC power cord to the

wall outlet, ensure that all other connections

have been made.

WARNING!

–For optimal performance, use only the

original power cable.

–Never make or change any connections

with the power switched on.

To avoid overheating of the system, a safety

circuit has been built in. Therefore, your

system may switch to Standby mode

automatically under extreme conditions. If

this happens, let the system cool down

before reusing it (not available for all versions).

speaker

(right)

speaker

(left)

FM wire antenna

AC power cord

BSpeakers Connection

Front Speakers

Connect the speaker wires to the SPEAKERS

terminals, right speaker to "RIGHT" and left

speaker to "LEFT", coloured (marked) wire to

"+" and black (unmarked) wire to "-".

●Fully insert the stripped portion of the speaker

wire into the terminal as shown.

Notes:

–For optimal sound performance, use the supplied

speakers.

– Do not connect more than one speaker to any

one pair of +/-speaker terminals.

– Do not connect speakers with an impedance

lower than the speakers supplied. Please refer to

the SPECIFICATIONS section of this manual.

MC146_05_UM_V2.0 2010.3.29, 15:507

English

Preparations

Inserting batteries into the

Remote Control

1Open the battery compartment.

2Insert two R03 or AAA batteries following the

indications (+/-) inside the compartment.

3Close the cover.

Using the Remote Control to

operate the system

1Aim the Remote Control directly at the remote

sensor (IR) on the front panel.

2Do not put any objects between the Remote

Control and the system while operating the

system.

CAUTION!

–Remove batteries if they are

exhausted or if the Remote Control is

not being used for a long time.

–Do not use old and new or different

types of batteries in combination.

–Batteries contain chemical substances,

so they should be disposed of properly.

MC146_05_UM_V2.0 2010.3.29, 15:508

English

Controls (illustrations on page 3)

Controls on the system and

remote control

1STANDBY-ON2(POWER)

– switches the system to standby or on.

2iR SENSOR

–infrared sensor for remote control.

3SOURCE

– selects the respective sound source for CD/

TUNER/AUX.

–switches on the system.

4PRESET +/-

for radio .............. selects a preset radio station.

5DBB (Dynamic Bass Boost)

– enhances the bass.

6TUNING 4 ¢

for Tuner ............. tunes to radio stations.

for CD ................. skips to the beginning of the

current/previous/subsequent

track.

................................. fast searches back and forward

within a track/CD.

for clock/timer adjusts the hours and minutes

for the clock/timer function

VOL +/-

–adjusts the volume level.

72;

–starts or interrupts CD playback.

8REPEAT

–repeats a track/ disc/ all programmed tracks.

9PROG

for CD ................. programmes tracks and reviews

the programme.

for Tuner ............. programmes tuner stations

manually or automatically.

–stops CD playback or erases a CD programme.

!PULLTO OPEN

–opens/closes the CD door.

AUX jack (located on the back panel)

– connects an external source (3.5 mm socket)

HEADPHONE (located on the back panel)

–connects headphones

Controls available on the remote

control only

@REP ALL

–repeats a track/disc/ all programmed tracks.

#SHUF

–plays CD tracks in random order..

$SLEEP

– activates/deactivates or selects the sleeper time.

%TIMER ON/OFF

–Turns on or off timer

^TIMER

–sets the timer function.

&2;

–starts or interrupts CD playback.

à/ á

for CD ................. fast searches back and forward

within a track/CD.

for Tuner ............. tunes to radio stations.

for clock/timer adjusts the hours and minutes

for the clock/timer function

¡/ ™

for CD ................. skips to the beginning of the

current/previous/subsequent

track.

*VOL +/-

–adjusts the volume level.

(MUTE

– interrupts and resumes sound reproduction.

)CLOCK/DISPLAY

for clock .............. sets the clock function.

................................. views clock.

MC146_05_UM_V2.0 2010.3.29, 15:509

English

Basic Functions

IMPORTANT:

Before you operate the system, complete

the preparation procedures.

Switching the system on

●Press STANDBY-ON 2or SOURCE

(POWER on the remote control).

➜The system will switch to the last selected

source.

●Press DISC, TUN or AUX on the remote

control.

➜The system will switch to the selected source.

To switch the system to standby mode

●Press STANDBY-ON 2on the system (or

POWER on the remote control).

Power-saving automatic standby

The power-saving feature automatically switches

to standby 15 minutes after a CD playback has

ended and no control is operated.

MICRO SYSTE M MC14 6

SOURC E

DBB

STANDBY-ON

VOL

TUNING

REPEAT PROG

CD/CD -R/CD -RW COMPATIBL E

PRESE T

Adjusting volume and sound

1Press VOL +/-to adjust volume.

➜Display shows the volume level VOL and a

number from 0-32.

2Press DBB to switch bass enhancement on or

off.

➜Display shows: if the DBB is activated.

3Press MUTE on the remote control to

interrupt sound reproduction instantly.

➜Playback will continue without sound.

●To activate sound reproduction you can:

–press MUTE again;

–adjust the volume controls;

–change source.

MC146_05_UM_V2.0 2010.3.29, 15:5010

Otros manuales para MC146/05

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Micro sistema de música de Philips

Philips

Philips MC175/01 Manual de usuario

Philips

Philips DCM186/05 Manual de usuario

Philips

Philips MCM149/98 Manual de usuario

Philips

Philips MCM710/61 Manual de usuario

Philips

Philips MCM205/12 Manual de usuario

Philips

Philips MCD302/93 Manual de usuario

Philips

Philips DCM292/12 Manual de usuario

Philips

Philips MCM1006/93 Manual de usuario

Philips

Philips MCM2050/05 Manual de usuario

Philips

Philips MCM239D/79 Manual de usuario

Philips

Philips MCM2300 Manual de usuario

Philips

Philips DCM2020/96 Manual de usuario

Philips

Philips BTM2280 Manual de usuario

Philips

Philips MCD268/93 Manual de usuario

Philips

Philips DCM1075/96 Manual de usuario

Philips

Philips MCD122/51 Manual de usuario

Philips

Philips BTB7150 Manual de usuario

Philips

Philips MCM166/07 Manual de usuario

Philips

Philips MBD3000/12 Manual de usuario

Philips

Philips DCM3020/12 Manual de usuario

Philips

Philips MCM305/12 Manual de usuario

Philips

Philips DCM3120/12 Manual de usuario

Philips

Philips MCM277 Manual de usuario

Philips

Philips DCM292/96 Manual de usuario

Manuales populares de Micro sistema de música de otras marcas

Rautz

Rautz MC-5100DU Manual de usuario

Sanyo

Sanyo DC-D9 Manual de usuario

Curtis

Curtis RCD744 Manual de usuario

Samsung

Samsung MM-UC8 Manual de usuario

Akai

Akai AMP300UCI Manual de usuario

Hyundai

Hyundai MS 132 DU3BL Manual de usuario

JVC

JVC UX-GP5 Manual de usuario

Tiger Electronics

Tiger Electronics Hitclips Beat Bot 6000 Manual de usuario

Optimus

Optimus SYSTEM 731 Manual de usuario

Hitachi

Hitachi AXM209UK Manual de usuario

Sharp

Sharp XL-MP110DVD Manual de usuario

Tiger Electronics

Tiger Electronics Hitclips Micro Music Watch 59947 Manual de usuario

ProAudio

ProAudio MC 9010 iP Manual de usuario

Samsung

Samsung MM-ZJ9 Manual de usuario

Sharp

Sharp MD-X7 Manual de usuario

Sharp

Sharp DK-KP95P Manual de usuario

Akura

Akura APTCDC832PR Manual de usuario

iLive

iLive IHB248B Manual de usuario