Philips EasyAir SNS210 MC Manual de usuario
Single, compact, cost-effective
luminaire control
Philips EasyAir SNS210 MC
March 2020
Design-in Guide
Sensors
EasyAir
SNS210 MC
2Design-in Guide - EasyAir SNS210 March 2020
Contents
Introduction to this guide 3
More information or support 3
Warnings and instructions 4
Introduction of EasyAir SNS210 MC 5
Product characteristics 6
EasyAir SNS210 MC overview 6
Zigbee and Bluetooth Low Energy 6
Motion detector 7
Sensor view shield 8
Light sensor 9
LED indicator 9
Mechanical design-in 10
Wire strip length 10
Wire insertion 10
Wire separation from the connector 10
Wiring Information 10
Wire distance for remote mounting 11
Luminaire-to-luminaire distance 11
Recommendations to design-in around EasyAir
SNS210 MC with good RF signal 11
Recommendations to design-in a luminaire
around EasyAir SNS210 MC with good RF signal 11
Mounting to a luminaire 12
Mounting in a bracket (SMB-50) 13
Installing EasyAir SNS210 MC with ceiling
mount bracket (SNS210 MCCMP) 14
EasyAir SNS210 MC with multiple Philips Xitanium
SR LED drivers (1:N application) 15
Luminaire Production Test 16
FAQ 17
Contact details 19
Philips EasyAir SNS210 MC 19
Disclaimer 20
3Design-in Guide - EasyAir SNS210 March 2020
Introduction to this guide
Thank you for choosing Philips EasyAir SNS210 MC. In this
guide luminaire manufacturers will find the information
required to design this product into a luminaire and
configure it to suit specific applications. This design-in
guide covers sensor functionality, mechanical mounting,
wiring details, configuration and commissioning (grouping)
method, application notes and frequently asked questions.
For sensor specifications, please see the datasheet
available at www.lighting.philips.co.uk/oem-emea/
products/connected-lighting.
More information or support
For further information or support, please consult your
local Philips sales representative or visit
www.lighting.philips.co.uk/oem-emea/support/technical-
downloads.
Philips EasyAir SNS210 MC
4Design-in Guide - EasyAir SNS210 March 2020
Warnings and instructions
• EasyAir SNS210 MC must be used with Philips Xitanium
SR LED drivers.
• Do not apply mains power directly to the sensor.
• Do not cover the sensor during operation or mount the
sensor internal to the luminaire.
• External infrared light source in the space might have
influence on occupancy detection.
• Incorrect location of sensor (e.g., with setting up of
multiple SNS210 devices into a single network or a group
with addition of qualified wireless switches obstructions
in viewing angle) will result in incorrect functioning of
occupancy detection.
• Faulty settings of the sensor might result in undefined
startup.
• Make sure the sensor, especially the occupancy detection
lens, is protected from damage during shipment and
handling.
• The application area of EasyAir SNS210 MC is designed
for a typical indoor environment (open/private offices,
conference rooms, classrooms, corridors, etc.) in normally
heated and ventilated areas. EasyAir SNS210 has no
protection against aggressive chemicals or water.
• Make sure the the EasyAir SNS210 MC Zigbee/Bluetooth
antenna is not covered by metal for proper RF
communication.
5Design-in Guide - EasyAir SNS210 March 2020
Introduction of EasyAir SNS210 MC
The Philips EasyAir SNS210 MC is the ideal solution for
per-luminaire control of smart luminaires. It combines
occupancy sensing, daylight harvesting and task tuning in a
single, compact package for easy OEM luminaire assembly.
EasyAir SNS210 MC operates with the established Xitanium
SR LED driver standard to make a simple two-wire
connection between sensor and driver, thus eliminating
the need for multiple components and auxiliary devices.
The result is a cost-effective and easy-to-design-in
solution ideal for energy-savings. An intuitive
MasterConnect app makes commissioning and
configuration during and after installation fast and easy.
EasyAir SNS210 MC enables grouping allows scene setting
on a wireless switch (e.g., presentation mode for a
conference room) as well as occupancy sharing (i.e.,
luminaires within a group can be programmed to remain at
prescribed light levels so long as occupancy is detected
anywhere in the group).
For more details on specification and ordering codes,
please refer to the SNS210 MC datasheet on the technical
downloads page.
www.lighting.philips.co.uk/oem-emea/support/technical-
downloads
6Design-in Guide - EasyAir SNS210 March 2020
Product characteristics
EasyAir SNS210 MC overview
EasyAir SNS210 MC contains multiple functions in one
housing and uses two wires to connect with an SR driver.
(See wiring diagram in the Mechanical design-in section.)
Functions include:
• Zigbee/Bluetooth
LE antenna
• Occupancy sensor (PIR)
• Light sensor
• LED indicator
EasyAir SNS210 MC is designed for a typical indoor
environment (open/private offices, conference rooms,
classrooms, corridors, etc.) in normally heated and
ventilated areas. The sensor is normally mounted to a
luminaire and is optimized for a sensor mounting height of
2.5 m to 3 m.
Zigbee and Bluetooth Low Energy (BLE)
The Zigbee-BLE antenna should not be covered by metal
and should be exposed to free air to ensure there is
sufficient range.
For more information on mechanical design in of the
sensor, please refer the section on page 11.
7Design-in Guide - EasyAir SNS210 March 2020
X1
X2
Y1
Y2
H
Motion detector
The occupancy sensor is a PIR (Passive Infrared) sensor
that detects movement with an X-Y cross-area under an
angle of X = 62° and Y = 84°. Two types of movements
are defined as follows:
• Major movement: movement of a person walking into or
through an area.
• Minor movement: movement of a person sitting at an
office desk reaching for a telephone, turning the pages in
a book, opening a file folder, picking up a coffee cup, etc.
When installed in a typical office ceiling at height, the
sensor is sensitive to minor movements within X1 by Y1
area. It will respond to minor movements down to a few
centimeters at the task area of a desk and is sensitive
to major movements within a range of X2 by Y2. The
directions X1, X2 are parallel to direction X; likewise for Y1,
Y2 being parallel to Y. The maximum recommended height
to place the sensor in the ceiling is 3 m to assure
movement coverage and detection. The PIR sensor reacts
on movement by means of a temperature difference, such
as the human body temperature versus its surrounding
temperature e.g. people. People sitting behind a
transparent shield or glass window are not seen by PIR
sensor of SNS210. Please refer to the table below for
coverage area details.
Figure 1. Motion detection area. H: ceiling height. Minor movement detection area: X1 by Y1. Major movement detection area: X2 by Y2.
X
Y
Minor movement Major movement
Height X1 Y1 X2 Y2
2.4m 1.9 2.9 2.9 4.3
3.0m 2.4 3.6 3.6 5.4
8Design-in Guide - EasyAir SNS210 March 2020
Sensor view shield
The sensor comes with an occupancy view shield that can
be used to block the movement detection by the sensor in
a certain area. The shield comes inverted. (See Figure 2.)
This view shield can be pulled out, flipped and inserted
back in the sensor and then rotated so the correct area is
shielded off from the detection area. If such shield is not
needed in the application, it can be easily pulled out from
the sensor or left as in the original position.
To prevent false triggers, the EasyAir SNS210 MC must
be mounted more than 2 m away from air vents in all
directions, see figures below:
> 2m
> 2m
Luminaire
> 2m
> 2m
• Occupancy view shield
Figure 2. Sensor view shield.
9Design-in Guide - EasyAir SNS210 March 2020
Photocell
Window
h
Windowsill
eld of view
(= 0.7 x h)
Field of viewY (cm)
H (cm)
100
120
90
60
30
0
150 200
300
250
Light sensor
The light sensor is a photo diode that reads the average light
level captured under an angle of approximately 40°. This
level depends on the amount of artificial and/or natural
light supplied in the office, as well as how this light is
reflected toward the ceiling/sensor. The EasyAir SNS210 MC
converts the illuminance signal into ON/OFF or dimming
commands to the Philips Xitanium SR LED driver in order to
maintain a constant light level on the desk.
The sensor should be installed with a minimum distance of
0.6 m to the window to avoid the sensor looking outside.
When the sensor is mounted too close to the window it will
look partly outside. Sun reflection from cars or snow can
reflect directly into the sensor. The sensor will then measure
such high illumination levels that it will drive the artificial
light to its minimal level or even switch off the artificial
lights. The optimum distance [Y] from the window to EasyAir
SNS210 MC can be obtained from Figure 4. This graph
shows the relation between the distance from the window
to the sensor [Y] and the height [H] of the sensor (H, height
of the sensor measured from ceiling to bottom of window
sill).
LED indicator
The product contains a LED indicator. This is enabled by
default, and it can be disabled through the app. The
behavior of the LED is as follows:
Yellow LED on: = vacancy & light sensor are functional.
Red LED on: = motion is detected and hold time is not
expired yet.
Figure 3. Sensor placement.
Figure 4. Sensor mounting height from window sill (Y) vs. sensor horizontal distance from
window sill (H).
10 Design-in Guide - EasyAir SNS210 March 2020
Mechanical design-in
Wiring Information
Applicable wires
Conductor size: solid 0.2 - 0.75 mm2
Conductor size: fine-stranded 0.2 - 0.75 mm2
Conductor size: fine-stranded 0.25 - 0.34 mm2
(with insulated formule)
Conductor size: fine-stranded 0.25 - 0.34 mm2
(with insulated formule)
AWG 24 - 18
Strip length 7 - 9 mm / 0.28 - 0.35 in
Note: Stranded wires without ferrule should be soldered
Strip length
8.0 ± 0.5 mm
Conductor
[ Conductor: Bare Copper / Strand wire ]
Insulation
5°~7° Angle Max
Insertion
[ Inserting solid conductors via push-in terminal ]
2. Pull-out
1. Push
Wire strip length
Wire insertion
Wire separation from the connector
Inserting solid conductors via push-in terminal
Tabla de contenidos
Otros manuales de Accesorios de Philips
Philips
Philips SVC1116/10 Manual de usuario
Philips
Philips HF3490/01 Manual de usuario
Philips
Philips dynalite DUS704C Manual de usuario
Philips
Philips GC012 Manual de usuario
Philips
Philips EasyAir SNS300 Manual de usuario
Philips
Philips SH90/81 Manual de usuario
Philips
Philips INFRACARE HP3643 Manual de usuario
Philips
Philips 22PP2102 Manual de usuario
Philips
Philips HR 2577 Manual de usuario
Philips
Philips HS85/44 Manual de lista de piezas
Philips
Philips OccuSwitch Classic LRL2380 Guía de instalación
Philips
Philips SJM2007 Manual de usuario
Philips
Philips SmartSleep Manual de usuario
Philips
Philips GoZero Manual de usuario
Philips
Philips DLA71016 Manual de usuario
Philips
Philips HF3520 series Manual de usuario
Philips
Philips CA6521 Manual de usuario
Philips
Philips SVC3520W Manual de usuario
Philips
Philips Norelco HQ6/32 Manual de usuario
Philips
Philips DUS804CS-UP Manual de usuario
