PhDsolutions MXC-U-P442-A-HDTL Manual de usuario
CPLUS-442CVAL
4×6 HDMI and HDBaseT Matrix
Operation Manual
Operation Manual
MXC-U-P442-A-HDTL
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fi re,
electrical shock and injury to persons.
• To prevent fi re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
suffi cient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE (DD/MM/YY) SUMMARY OF CHANGE
VS1 24/10/16 Updated text/diagrams
VS2 18/04/17 Corrections to section 6.4
CONTENTS
1. Introduction......................................................1
2. Applications.....................................................1
3. Package Contents ..........................................1
4. System Requirements......................................2
5. Features............................................................2
6. Operation Controls and Functions.................3
6.1 Front Panel ................................................. 3
6.2 Rear Panel.................................................. 4
6.3 Side Panel .................................................. 6
6.4 Remote Control......................................... 7
6.5 OLED Menu ................................................ 8
6.6 IR Cable Pin Assignment........................... 9
6.7 RS-232 Protocol.......................................... 9
6.8 RS-232 and Telnet Commands .............. 10
6.8.1 Command Syntax.......................... 10
6.8.2 Full Command List.......................... 11
6.9 Telnet Control .......................................... 19
6.10 WebGUI Control .................................... 21
6.10.1 Video Switch................................. 23
6.10.2 Zone Video Pairing ...................... 26
6.10.3 EDID Settings................................. 27
6.10.4 HDBaseT & H/W Info..................... 29
6.10.5 User Confi g ................................... 30
6.10.6 System Settings............................. 30
6.10.7 Logout ........................................... 31
7. Connection Diagram ....................................32
8. Specifi cations ................................................33
8.1 Technical Specifi cations ........................ 33
8.2 Supported Video Formats...................... 34
8.2.1 Supported HDMI Resolutions ........ 34
8.2.2 Maximum HDMI Cable Length..... 34
8.3 Supported Audio Formats ...................... 35
8.3.1 Linear PCM Audio .......................... 35
8.3.2 Compressed Audio........................ 35
8.4 Category Cable Specifi cations............. 36
8.5 HDBaseT Features.................................... 36
9. Acronyms .......................................................37
1
1
1. INTRODUCTION
This 4×6 HDMI/HDBaseT Matrix supports routing and transmission of
video (resolutions up to 4K@60Hz w/ HDMI 2.0 & HDCP 2.2) and audio
(multi-channel digital/stereo analog) while providing fl exible control
via IR, RS-232, Telnet or WebGUI. As many as four HD sources may be
routed to any of six destinations via a single Cat.5e/6/7 cable (up to
60m at 1080p or up to 40m at 4K@30Hz). The two HDMI 2.0 outputs
support transmission of 6G UltraHD HDMI sources (up to 4K@60Hz, 4:4:4)
from any HDMI input or they can mirror any of the HDBaseT outputs
for local monitoring. 3D video is also supported when compatible
sources and displays are connected. This product supports passing
7.1 channel LPCM digital audio as well as advanced bitstream and
HD bitstream audio formats. Additionally, four analog audio outputs
are available to provide stereo breakout audio from the associated
HDBaseT output (LPCM 2.0 sources only).
The Power over HDBaseT (PoH) function can power compatible
receivers, providing greater fl exibility in your installations. Control is via
manual selection buttons, WebGUI, Telnet, RS-232 or IR remote.
2. APPLICATIONS
• Full audio/video matrix systems
• Residential AV matrix installations
• Commercial AV matrix installations
• Security systems
• University lecture hall systems
• Retail installation systems
3. PACKAGE CONTENTS
• 1× 4 by 6 HDMI/HDBaseT Matrix
• 1× Remote Control (CR-163)
• 2× IR Extender Cable
• 2× IR Blaster Cable
• 1× 24V/6.25A DC Power Adaptor
• 1× Power Cord
2
2
• 1× Rack Ear Set
• 1× Operation Manual
4. SYSTEM REQUIREMENTS
• HDMI or DVI source equipment such as media players, video game
consoles, set-top boxes, PCs or laptops. DVI equipped source
devices must be connected via DVI to HDMI cables/adapters
• HDMI receiving equipment such as HDTVs, monitors or audio
amplifi ers
• The use of industry standard Cat.6, Cat.6a or Cat.7 cable is highly
recommended
• The use of “Premium High Speed HDMI” cables is highly
recommended
5. FEATURES
• HDMI 2.0, HDCP 1.4 and HDCP 2.2 compliant
• Routes four HDMI sources to six displays using four HDBaseT outputs
and two independent or mirrored HDMI outputs
• HDBaseT feature support: High-Defi nition video and audio, PoH
(Power over HDBaseT) and control (Bi-directional IR & RS-232 pass-
through)
• Supported HDBaseT resolutions: VGA~WUXGA, 480i~1080p,
4K@24/25/30Hz (RGB, YUV 4:4:4 & YUV 4:2:2) & 4K@60Hz (YUV 4:2:0)
dependent upon the output display’s EDID settings
• Supports HDMI output resolutions up to 4K@60Hz (RGB/YUV 4:4:4)
• Supports automatic 4K@60Hz RGB/YUV 4:4:4 to YUV 4:2:0 conversion
for HDBaseT outputs
• 4K@30Hz signals can be transmitted up to 35m via Cat.5e/6 and up
to 40m via Cat.6a/7
• Supports pass-through of all standard digital audio formats: LPCM
2.0/5.1/7.1, bitstream, and HD bitstream
• Supports Digital to Analog Conversion (DAC)
• Advanced internal and external EDID management with 4 sets of
confi gurable EDID settings
3
3
• Bi-directional IR support over HDBaseT
• Control via front panel controls, Ethernet (Telnet & WebGUI), RS-232,
& IR remote
• 1U rack mounted design
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
2.2
isolated
+
35M
ABCDE
F
12345
698710
LOCK
ENTER
PRESET
/CANCEL
IN
OUT
+
-
MENU
1 2 3 6 7 8 95 104
1POWER: Press this button to power the unit on or place it into stand-
by mode.
Note: Network functionality and PoH remain active when the unit
is in stand-by mode.
2POWER LED: This LED will illuminate GREEN to indicate the unit is on
and receiving power. When the unit is in stand-by mode the LED
will illuminate RED.
3IR WINDOW: Accepts IR signals from the included IR remote for
control of this unit only.
4OUTPUT A~F, INPUT 1~4 & Number 1~10: Press the “OUT” button to
enter output selection mode. Next, press the output keys (A~F) of
the outputs you wish to route a source to (they will fl ash to indicate
selection). Next, press the “IN” key followed by the input (1~4)
you wish to route to the selected outputs. Finally, press “ENTER” to
confi rm your selection and execute the routing change.
For example, if you wish to display input 1 on outputs A~D then the
following sequence of button presses should be performed: OUT →
A, B, C, D → IN → 1 → ENTER
When directly entering Ethernet address information into the unit
all 10 buttons are used to represent the numbers from 0 to 9 (button
10 = 0) to make number entry more streamlined.
5MENU/CANCEL: Press the “MENU/CANCEL” button to enter the
4
4
OLED menu, or to back out from menu items. For a description of
the menu tree, please refer to section 6.6.
6ENTER: Press this button to confi rm selections.
7+/IN: Within the menu, this button moves you up within the menu
tree. Otherwise, in routing mode, this button allows you to make
your input source selection.
-/OUT: Within the menu, this button moves you down within the
menu tree. Otherwise, this button starts routing mode and allows
you to begin your output destination selections.
8PRESET: Press this button to recall saved presets. A maximum of 8
presets can be stored in the unit. Presets are created and stored
via the WebGUI. Please refer to section 6.10.1 for advanced preset
settings.
9LOCK: Press and hold this button for 3 seconds to lock/unlock
all buttons on the front panel. The OLED will display an “L” in the
upper right corner to indicate the front panel is locked.
10 OLED WINDOW: Displays the unit’s menu, settings and information.
6.2 Rear Panel
1
2
3
4
V+
GND
GND GND
V+
CONTROL SERVICE MAIN 24V
RS232
ALL
IR IN
IR OUT
IR IN IR IN IR IN IR IN
CAT5e/6/7 OUTCAT5e/6/7 OUTCAT5e/6/7 OUTCAT5e/6/7 OUT
HDMI IN HDMI IN HDMI IN HDMI IN HDMI OUT HDMI OUT
IR OUT IR OUT IR OUT IR OUT
ZONE
AUDIO OUT
AUDIO OUT
ABCD
RLRLRLRL
1234
EFABCD
6 7
4 5 8 9 10
1 2 3
1HDMI IN & IR OUT 1~4: Connect up to 4 source devices to the
HDMI ports using appropriate quality HDMI cables. Input source
devices include Blu-ray players, set-top boxes, game systems
and so on. These inputs are DVI-D compliant (with the use of
DVI to HDMI adapters or cables). Attach IR blasters to the IR Out
ports to transmit the IR signals received from connected HDBaseT
Receivers. The IR signal routing follows the HDMI signal routing.
Note: The use of “Premium High Speed HDMI” cables is highly
recommended.
2HDMI OUT E & F: Connect up to 2 HDMI displays using these HDMI
output ports. These two HDMI ports can be either independent
5
5
high bandwidth (6G) outputs, or they can be confi gured to mirror
two of the HDBaseT outputs for local monitoring or recording
purposes.
Note: 4K signals with HDR (High Dynamic Range) or Deep Color
are supported by the 2 HDMI output ports, however they are not
supported by the HDBaseT outputs due to bandwidth limitations.
If your HDR source needs to be output over the HDBaseT outputs
please remember to disable the HDR support on your source
device or use a non-HDR supporting EDID.
3CAT5e/6 OUT & IR IN A~D: Connect the Cat.5e/6 outputs via an
appropriate cable to the input ports of compatible HDBaseT
receivers for HDMI audio/video and IR/RS-232 control signal
transmission. In order for an IR signal to be transmitted along
with the HDMI signal an IR extender must be connected to the
associated IR In port. IR signals coming back from the connected
HDBaseT receiver can be used to control the matrix remotely
and will also be broadcast from IR blasters connected to the
appropriate IR Out/All IR Out ports.
Note: 4K signals with HDR (High Dynamic Range) or Deep Color
are supported by the 2 HDMI output ports, however they are not
supported by the HDBaseT outputs due to bandwidth limitations.
If your HDR source needs to be output over the HDBaseT outputs
please remember to disable the HDR support on your source
device or use a non-HDR supporting EDID.
4IR IN (ALL): Connect an IR extender to this port for IR signal
reception. All IR signals received will be broadcast by all IR blasters
connected to the matrix or connected HDBaseT receivers. Please
ensure that the remote being used is within direct line-of-sight of
the IR extender.
5IR OUT (ALL): Connect an IR Blaster to this port to broadcast IR
signals. All IR signals received by any IR extenders connected to
the matrix or HDBaseT receivers will be broadcast. Please place the
IR Blaster in direct line-of-sight of the equipment to be controlled.
6AUDIO OUT A~D: Four sets of stereo analog audio outputs. These
audio ports mirror the audio output from the associated HDBaseT
output (LPCM 2.0 sources only).
7RS-232: Connect directly to your PC/laptop to send RS-232
commands to control the unit (refer to section 6.7).
Tabla de contenidos
Otros manuales de Conmutador de matriz de PhDsolutions
PhDsolutions
PhDsolutions MX-4H4H-4K Manual de usuario
PhDsolutions
PhDsolutions MXC-P442-HDTL Manual de usuario
PhDsolutions
PhDsolutions MX-2H4H-4K Manual de usuario
PhDsolutions
PhDsolutions MXC-UHD-P8X8-HDTE Manual de usuario
PhDsolutions
PhDsolutions MXC-P8X8-HDTE Manual de usuario
PhDsolutions
PhDsolutions MXC-U-P882-HDTL-PRO-KIT Manual de usuario
PhDsolutions
PhDsolutions HDBaseT MXC-4K888-HDT150-KIT Manual de usuario
PhDsolutions
PhDsolutions MXC-U-P882-HDTL-A Manual de usuario
PhDsolutions
PhDsolutions ECO Series Manual de usuario
PhDsolutions
PhDsolutions MXC-P8X8-HDT Manual de usuario
