Perle RPS830 Manual de usuario

5500193-12

RPS Series

Remote Power Switches

Models Covered:

RPS820

RPS830

RPS1620H

RPS1630H

User's Guide

Warnings and Cautions:

Installation Instructions

Secure Racking

If Secure Racked units are installed in a closed or multi-unit rack assembly, they may require

further evaluation by Certication Agencies. The following items must be considered.

1. The ambient within the rack may be greater than room ambient. Installation should be

such that the amount of air ow required for safe operation is not compromised. The

maximum temperature for the equipment in this environment is 55°C. Consideration

should be given to the maximum rated ambient.

2. Installation should be such that a hazardous stability condition is not achieved due to

uneven loading.

3. Side vents are used to dissipate heat generated within the unit. When mounting the unit in

an equipment rack, make certain to allow adequate clearance for venting.

Input Supply

Check nameplate ratings to assure there is no overloading of supply circuits that could have an

effect on overcurrent protection and supply wiring.

Grounding

Reliable earthing of this equipment must be maintained. Particular attention should be given to

supply connections when connecting to power strips, rather than direct connections to the

branch circuit.

No Serviceable Parts Inside; Authorized Service Personnel Only

Do not attempt to repair or service this device yourself. Internal components must be serviced by

authorized personnel only.

• ShockHazard-DoNotEnter

• LithiumBattery

CAUTION:Dangerofexplosionifbatteryisincorrectlyreplaced.Replaceonlywith

sameorequivalenttyperecommendedbythemanufacturer.Discardusedbatteries

accordingtothemanufacturer'sinstructions.

Disconnect Power

If any of the following events are noted, immediately disconnect the unit from the outlet and

contact qualied service personnel:

1. If the power cord becomes frayed or damaged.

2. If liquid has been spilled into the device or if the device has been exposed to rain or water.

Two Power Supply Cables

Note that RPS series units feature two separate power circuits, and a separate power supply cable

for each power circuit. Before attempting to service or remove his unit, please make certain to

disconnect both power supply cables are disconnected.

Agency Approvals

FCC Part 15 Regulation

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation

WARNING: Changes or modications to this unit not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment

EMC, Safety, and R&TTE Directive Compliance

The CE mark is afxed to this product to conrm compliance with the following European

Community Directives:

• CouncilDirective89/336/EECof3May1989ontheapproximationofthelawsof

MemberStatesrelatingtoelectromagneticcompatibility;

 and

• CouncilDirective73/23/EECof19February1973ontheharmonizationofthelaws

ofMemberStatesrelatingtoelectricalequipmentdesignedforusewithincertain

voltagelimits;

 and

• CouncilDirective1999/5/ECof9Marchonradioequipmentandtelecommunications

terminalequipmentandthemutualrecognitionoftheirconformity.

iii

Table of Contents

1. Introduction.....................................................................1-1

2. UnitDescription.................................................................2-1

2.1. RPS Front Panel ............................................................2-1

2.2. RPS Series - Back Panel ......................................................2-2

2.3. Additional Button Functions ...................................................2-3

3. GettingStarted..................................................................3-1

3.1. Components ...............................................................3-1

3.1.1. You Need to Supply ...................................................3-1

3.2. Hardware Installation ........................................................3-1

3.3. Applying Power to the RPS ...................................................3-2

3.4. Connecting the Device Server to the RPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

3.5. Connecting the Device Server to the RPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

3.6. Conguring the RPS Standalone .................................................3-3

4. HardwareInstallation............................................................. 4-1

4.1. Power Supply Connection .....................................................4-1

4.1.1. Installing the Cable Keepers .............................................4-1

4.2. Connection to Switched Outlets ................................................4-2

4.3. SetUp Port Connection .......................................................4-2

4.3.1. Connecting a Local PC .................................................4-2

4.3.2. Connecting an External Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

4.4. Connecting the Network Cable .................................................4-3

5. BasicConguration..............................................................5-1

5.1. Communicating with the RPS Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

5.1.1. The Text Interface .....................................................5-1

5.1.2. The Web Browser Interface .............................................5-2

5.2. Conguration Menus ........................................................5-3

5.3. Dening System Parameters ...................................................5-4

5.3.1. The Real Time Clock and Calendar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

5.3.2. The Invalid Access Lockout Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

5.3.3. Log Conguration .....................................................5-9

5.3.3.1. Audit Log Conguration Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10

5.3.3.2. Reading, Downloading and Erasing Logs . . . . . . . . . . . . . . . . . . . . . . . . . 5-10

5.3.4. Callback Security ....................................................5-11

5.3.5. Scripting Options ....................................................5-12

5.3.5.1. Automated Mode ............................................5-14

5.4. User Accounts .............................................................5-15

5.4.1. Command Access Levels ..............................................5-15

5.4.2. Plug Access .........................................................5-16

5.4.3. Port Access .........................................................5-16

5.5. Managing User Accounts ....................................................5-17

5.5.1. Viewing User Accounts ................................................5-17

5.5.2. Adding User Accounts ................................................5-17

5.5.3. Modifying User Accounts ..............................................5-19

5.5.4. Deleting User Accounts ...............................................5-19

Table of Contents

5. BasicConguration(Continued)

5.6. The Plug Group Directory ...................................................5-20

5.6.1. Viewing Plug Groups .................................................5-20

5.6.2. Adding Plug Groups ..................................................5-21

5.6.3. Modifying Plug Groups ...............................................5-21

5.6.4. Deleting Plug Groups .................................................5-21

5.7. Dening Plug Parameters ....................................................5-22

5.7.1. The Boot Priority Parameter ............................................5-23

5.7.1.1. Example 1: Change Plug A3 to Priority 1 . . . . . . . . . . . . . . . . . . . . . . . . . 5-23

5.7.1.2. Example 2: Change Plug A5 to Priority 2 . . . . . . . . . . . . . . . . . . . . . . . . . 5-24

5.8. Serial Port Conguration ....................................................5-25

5.9. Network Conguration ......................................................5-27

5.9.1. Network Port Parameters ..............................................5-28

5.9.2. Network Parameters ..................................................5-29

5.9.3. IP Security ..........................................................5-31

5.9.3.1. Adding IP Addresses to the Allow and Deny Lists . . . . . . . . . . . . . . . . . . . 5-32

5.9.3.2. Linux Operators and Wild Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-32

5.9.3.3. IP Security Examples .........................................5-33

5.9.4. Static Route .........................................................5-34

5.9.5. Domain Name Server .................................................5-34

5.10. Save User Selected Parameters ................................................5-35

5.10.1. Restore Conguration .................................................5-35

6. TheStatusScreens...............................................................6-1

6.1. Product Status ..............................................................6-1

6.2. The Network Status Screen ....................................................6-2

6.3. The Plug Status Screen .......................................................6-3

6.4. The Plug Group Status Screen .................................................6-4

7. Operation.......................................................................7-1

7.1. Operation via the Web Browser Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

7.1.1. The Plug Control Screen - Web Browser Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

7.1.2. The Plug Group Control Screen - Web Browser Interface . . . . . . . . . . . . . . . . . . . . . .7-2

7.2. Operation via the Text Interface ................................................7-3

7.2.1. Switching and Reboot Commands - Text Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3

7.2.2. Applying Commands to Several Plugs - Text Interface . . . . . . . . . . . . . . . . . . . . . . . . 7-5

7.3. The Automated Mode ........................................................7-6

7.4. Manual Operation ...........................................................7-7

7.5. Logging Out of Command Mode ...............................................7-7

8. SyslogMessages..................................................................8-1

8.1. Conguration ..............................................................8-1

9. SavingandRestoringCongurationParameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

9.1. Sending Parameters to a File ...................................................9-1

9.2. Restoring Saved Parameters ...................................................9-2

9.3. Restoring Previously Saved Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3

10. UpgradingRPSFirmware........................................................10-1

10.2. The Upgrade Firmware Function ..............................................10-1

Table of Contents

11. CommandReferenceGuide.......................................................11-1

11.1. Command Conventions ......................................................11-1

11.2. Command Summary ........................................................11-2

11.3. Command Set .............................................................11-3

11.3.1. Display Commands ...................................................11-3

11.3.2. Control Commands ...................................................11-5

11.3.3. Conguration Commands ..............................................11-9

Appendices:

A. Specications.................................................................Apx-1

B. InterfaceDescriptions..........................................................Apx-2

B.1. SetUp Port .............................................................. Apx-2

C. CustomerService............................................................. Apx-3

C.1. Contacting Technical Support ............................................... Apx-3

Table of Contents

List of Figures

2.1. Front Panel (RPS16 Series Shown) .................................................2-1

2.2. Back Panel (Model RPS1630H Shown) ..............................................2-2

5.1. Boot Priority Example 1 .........................................................5-23

5.2. Boot Priority Example 2 .........................................................5-24

B.1. SetUp Port Interface (RJ45, Cisco Pinout) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-2

1-1

1. Introduction

Electronic equipment sometimes "locks-up" requiring a service call just to ip the power switch

to perform a simple reboot. RPS Series Remote Power Switches give you the ability to perform

this function remotely. If secure remote access is an issue, you can communicate through Perle’s

IOLAN DS product line to securely manage the power status of your electronic equipment.

To congure your environment for an RPS and a Perle IOLAN DS product, refer to the SCS/SDS/

STS User’s Guide. When you are using the RPS independently, point your browser to the RPS’s

IP Address, enter the secure user name and password, and you’re just a click away from remote

power On, Off or Reboot.

IntelligentPowerControl

In addition to web browser access, the RPS can also communicate over any TCP/IP network

using standard Telnet, or out-of-band using an external modem and basic VT100 type terminal

emulation.

SecurityFeaturesandCo-LocationFeatures

To ensure security, web browser access requires the user to enter an assigned user name and

password. The RPS provides two levels of operational passwords; the System Administrator

Level, which allows access to all conguration and switching functions, and the User Level,

which only allows access to assigned plugs and cannot be used to change unit conguration.

The RPS also includes an address specic IP security mask, which can be employed to prevent

unauthorized network access to the RPS command mode.

EasytoCongure,EasytoUse

The RPS can be congured over the network, via modem, or locally via the RPS SetUp port.

Easy to use commands let you assign a location name, set system parameters and view plug

status. Outlets can be switched On, Off, or booted using plug numbers or names.

1-2

Introduction

FourDifferentRPSModels

This User’s Guide discusses four different RPS models. Throughout this User’s Guide, all four

units are referred to as the "RPS". Aside from the hardware conguration, all other features

function identically in both units except where noted.

The table below summarizes the four RPS units covered in this manual:

• RPS820: Horizontal mount. Eight (8) switched, 208 to 240 VAC,

IEC-320-C20 outlets. 32 Amps maximum total load (de-rated.)

One (1) Rack Unit.

• RPS830: Horizontal mount. Eight (8) switched, 100 to 120 VAC, NEMA 5-15R outlets.

32 Amps maximum total load (de-rated.)

One (1) Rack Unit.

• RPS1620H: Horizontal mount. Sixteen (16) switched, 208 to 240 VAC, IEC-320-C20

outlets. 32 Amps maximum total load (de-rated.)

Two (2) Rack Units.

• RPS1630H: Horizontal mount. Sixteen (16) switched, 100 to 120 VAC, NEMA 5-15R

outlets. 32 Amps maximum total load (de-rated.)

Two (2) Rack Units.

Typographic Conventions

Throughout this manual, typefaces and characters have been used to denote the following:

COURIER FONT Indicates characters typed on the keyboard.

For example, /ON 3 or /OFF 5.

[BoldFont] Text set in bold face and enclosed in square brackets indicates a

specic key. For example, [Enter] or [Esc].

2-1

2. Unit Description

2.1. RPS Front Panel

As shown in Figure 2.1, the RPS Series Front Panel includes the following components:

1. SetUpPort: An RJ45 RS232 serial port (DCE conguration) used for connection to a

local terminal or external modem, as described in Section 4.3. For a description of the

Setup Port interface, please refer to Appendix B.1.

2. "ON"Indicator: An LED which lights when power is applied to the RPS unit.

3. "RDY"Indicator: (Ready) Flashes if unit is ready to receive commands.

4. DefaultButton: Manually toggles outlets On/Off or resets unit to factory default

parameters as described in Section 2.3.

5. ResetButton: Reboots and/or resets the RPS to factory defaults as described in

Section 2.3.

Note: All Front Panel Button functions can also be disabled via the System

Parameters menu, as described in Section 5.3.

6. OutputStatusIndicators: LEDs light when corresponding outlet is switched On.

7. BranchACircuitBreakers: Two circuit breakers, which protect Branch A. One circuit

breaker protects outlets A1 through A4, and the other circuit breaker protects outlets A5

through A8.

8. BranchBCircuitBreakers: Same as Item 7 above, except circuit breakers protect

outlets on Branch B.

Remote Power Switch

SETUP PORT

DEFAULT

OUTPUT STATUS

RESET

ON RDY

A1 A2 A3 A4 A5 A6 A7 A8

B1 B2 B3 B4 B5 B6 B7 B8

A1 - A4 A5 - A8

B5 - B8B1 - B4

1 2 3 4 56 8

Figure 2.1: Front Panel (RPS16 Series Shown)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Perle

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario