Pepperl+Fuchs LC10 Series Manual de usuario

LC10-*

Laying loops for Loop detector

LC10-1 and LC10-2

FACTORY AUTOMAT ON

MANUAL

With regard to the supply of products, the current issue of the following document is ap-

plicable: The General Terms of Delivery for Products and Services of the lectrical Indus-

try, published by the Central Association of the lectrical Industry (Zentralverband

lektrotechnik und lektroindustrie (ZV I) e.V.) in its most recent version as well as the

supplementary clause: " xpanded reservation of proprietorship"

Manual LC10-*

1 ntroduction....................................................................................

1.1 Contents..................................................................................................

1.2 Target Group, Personnel........................................................................

1.3 Symbols Used ........................................................................................

2 General safety instructions ..........................................................

3 Product Description ......................................................................

3.1 Overview .................................................................................................

3.2 Use and Application ..............................................................................

3.3 ndicators and Operating Controls.......................................................

3.3.1 LC10-1-* ..............................................................................................

3.3.2 LC10-2-* ..............................................................................................

3.4 nterfaces and connections ..................................................................

3.5 Dimensions.............................................................................................

4 nstallation......................................................................................

4.1 Preparation .............................................................................................

4.1.1 Laying loops.........................................................................................

4.1.2 Number of loop windings .....................................................................

4.1.3 Loop test..............................................................................................

4.2 nstallation ..............................................................................................

5 Commissioning..............................................................................

5.1 Test function ...........................................................................................

5.2 Loop geometry .......................................................................................

5.3 Loop interference...................................................................................

5.4 nfluencing variables .............................................................................

6 Troubleshooting.............................................................................

Manual LC10-*

2016-11

Manual LC10-*

Introduction

1 Introduction

1.1 Contents

This document contains information that you need in order to use your product throughout the

applicable stages of the product life cycle. These can include the following:

■

Product identification

■

Delivery, transport, and storage

■

Mounting and installation

■

Commissioning and operation

■

Maintenance and repair

■

Troubleshooting

■

Dismounting

■

Disposal

The documentation consists of the following parts:

■

Present document

■

Instruction manual

■

Datasheet

Additionally, the following parts may belong to the documentation, if applicable:

■

U-type examination certificate

■

U declaration of conformity

■

Attestation of conformity

■

Certificates

■

Control drawings

■

Additional documents

1.2 Target Group, Personnel

Responsibility for planning, assembly, commissioning, operation, maintenance, and

dismounting lies with the plant operator.

Only appropriately trained and qualified personnel may carry out mounting, installation,

commissioning, operation, maintenance, and dismounting of the product. The personnel must

have read and understood the instruction manual and the further documentation.

Prior to using the product make yourself familiar with it. Read the document carefully.

Note!

This document does not substitute the instruction manual.

Note!

For full information on the product, refer to the instruction manual and further documentation on

the Internet at www.pepperl-fuchs.com.

Manual LC10-*

Introduction

2016-11

1.3 Symbols Used

This document contains symbols for the identification of warning messages and of informative

messages.

Warning Messages

You will find warning messages, whenever dangers may arise from your actions. It is mandatory

that you observe these warning messages for your personal safety and in order to avoid

property damage.

Depending on the risk level, the warning messages are displayed in descending order as

follows:

nformative Symbols

Action

This symbol indicates a paragraph with instructions. You are prompted to perform an action or

a sequence of actions.

Danger!

This symbol indicates an imminent danger.

Non-observance will result in personal injury or death.

Warning!

This symbol indicates a possible fault or danger.

Non-observance may cause personal injury or serious property damage.

Caution!

This symbol indicates a possible fault.

Non-observance could interrupt the device and any connected systems and plants, or result in

their complete failure.

Note!

This symbol brings important information to your attention.

2016-11

Manual LC10-*

General safety instructions

2 General safety instructions

Directives and Standards

Note!

Read the operating instructions before attempting commissioning.

Caution!

Installation, connection and adjustments should only be undertaken by specialist personnel.

Warning!

No safety component for protection of personnel or M RG NCY-STOP functions.

U-Directive Standards

2014/30/ U N 61000-6-2:2005

N 61000-6-4:20071A1 :2011

2014/35/ U N 60204-1 :20061A 1:2009

Manual LC10-*

Product Description

2016-11

3 Product Description

3.1 Overview

Together with the inductive loops laid beneath the surface, the LC series loop detectors form a

universal sensor system for detecting vehicles. People are not detected. Vehicles that enter the

inductive loop change the resonant frequency. This frequency change is measured and

analyzed by the microprocessor in the LC10 loop detector. The analysis is automatically and

periodically adjusted to the respective loop, ensuring that any changes in the loop inductance

caused by temperature, humidity or component age are automatically compensated for.

The loop detectors are control units that are fully functional without the need for any other

auxiliary equipment once the power supply and an inductive loop have been connected. The

inductive loop laid below the surface forms the inductor of a high-frequency oscillating circuit.

The metal parts of a vehicle that enters or is located in this wired loop cause the frequency of

the oscillation circuit to change. This frequency change is analyzed by the loop detector, and

the outputs, which are zero-potential relay contacts, can switch. The switching outputs are relay

contacts with a high switching power that can directly control contactors, valves and alternating

current motors. The dimensions of the detection area can be adjusted by changing the size and

shape of the inductive loops.

Figure 3.1 LC10-1 (left) and LC10-2 (right) loop detectors

3.2 Use and Application

Possible areas of application for the LC10-* series loop detectors are:

■

Selective vehicle detection

■

Opening impulse sensor for automatic gates and barrier systems

■

Presence checks for vehicles

■

Direction-specific vehicle checks

■

Controlling traffic light and vehicle detection systems

■

Ticket detection in parking garages

■

Managing tasks in automatic conveyor systems

2016-11

Manual LC10-*

Product Description

3.3 Indicators and Operating Controls

3.3.1 LC10-1-*

LED indicator

L D signals the allocation state of the loop (Loop allocated = L D On). A fault in the loop due to

a short-circuit or lead breakage and loop inductance outside the permissible range is indicated

by flashing of L D.

D P switches

It is possible to modify frequency, sensitivity and operating mode by using the DIP switch.

Sensitivity

The response sensitivity of the loop detector can be set in three stages by switches 3 and 4.

Frequency switches

The loop frequency can be set in four stages using the switches 1 and 2.

Operating mode switches

The following operating modes can be set with switches 5 and 6:

1L D indicator

2DIP switch

switch 3 switch 4 sensitivity

OFF ON low

ON OFF medium

ON ON high

Table 3.1 In the switch position "OFF", "OFF" the loop evaluation is switched off.

switch 1 switch 2 frequency

OFF OFF basic frequency f

ON OFF f - 10%

OFF ON f - 15%

ON ON f - 20%

Table 3.2 After actuation of the frequency switches 1 and 2 the loop must be readjusted with switches

3 and 4 set to "OFF", "OFF".

switch 7 switch 8 result

OFF - Pulse (0,8 s)when loop is allocated

ON - Pulse (0,8 s) when loop is abandoned

- ON Increased sensitivity (Boost)

Table 3.3 The increased sensitivity (Boost) is used for the detection of vehicles with high body

assemblies, e.g. HGVs.

ON OFF

BOOST

MODE

FREQ.

ON DIP

1 2 3 4 5 6

Manual LC10-*

Product Description

2016-11

3.3.2 LC10-2-*

LED indicators

Indications: L Ds 1 and 2 signal the allocation state of the loops (Loop 1 allocated = L D 1 on,

Loop 2 allocated = L D 2 on).

A fault in a loop due to a short-circuit or lead breakage and loop industance outside the

permissible range is indicated by flashing of the respective L D.

D P switches

It is possible to modify frequency, sensitivity and operating mode by using the DIP switch.

Sensitivity

The response sensitivity of the loop detector can be set in three stages using switches 3 and 4

(for loop 1) and switches 5 and 6 (for loop 2).

Frequency switches

The loop frequency can be set in four stages using the switches 1 and 2.

1L D indicator loop 2

2L D indicator loop 1

3DIP switch

switch 3 or 5 switch 4 or 6 sensitivity

OFF ON low

ON OFF medium

ON ON high

Table 3.4 In the switch position "OFF", "OFF" the loop evaluation is switched off.

switch 1 switch 2 frequency

OFF OFF basic frequency f

ON OFF f - 10%

OFF ON f - 15%

ON ON f - 20%

Table 3.5 After actuation of the frequency switches 1 and 2 the loop must be readjusted with switches

3 and 4 set to "OFF", "OFF".

2 31

CH2

CH1

ON OFF

BOOST

MODE

CH2

CH1

FREQ. CH1

ON DIP

1 2 3 4 5 6 7 8

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sensor de seguridad de Pepperl+Fuchs

Pepperl+Fuchs

Pepperl+Fuchs NBB15-30GM50-E2-V1-3G-3D Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs RMS-FRW Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs UC2000-30GM-IUEP-IO-V15-Y Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs NBB2-12GS40-Z4L-V1-3G-3D Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs ML71-55 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs UC6000-30GM-IUEP-IO-V15 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs NBN15-30GS50-Z4L-V1-3G-3D Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs INX360D-F99-I2E2-V15 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs VIM62PP-E1V16-0PE-I420V15 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs NBN8-18GS50-Z4L-V1-3G-3D Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs UC4000-30GM-IUEP-IO-V15 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs NBB10-30GS50-Z4L-V1-3G-3D Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs CCB10-30GS55-N1-V1 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs ACY04-F99-2I-V15 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs OBT300-R100-2EP-IO-L Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs UC2000-30GM-IUEP-IO-V15 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs KFD2-ELD-Ex16 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs UC2000-L2-E5-V15-Y291515 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs GLP30-RT/40b/103/123/143 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs VAS/M-2A8L-KE4-6SE-EV Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs DoorScan Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs schmersal RSS260 AS Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs NBB15-30GM50-E3-V1-3G-3D Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs SLP Series Manual de usuario

Manuales populares de Sensor de seguridad de otras marcas

THORLABS

THORLABS PDA10JT Manual de usuario

Waeco

Waeco UV-DETECT Manual de usuario

Intermatic

Intermatic IOS-DSIMF Manual de usuario

urmet domus

urmet domus 1083 Manual de usuario

Siemens

Siemens AZL66 Series Manual de usuario

BTI

BTI Profiline Multi Finder Manual de usuario

Challenger

Challenger SL01 Manual de usuario

DMP Electronics

DMP Electronics 1122INT Manual de usuario

Rielta

Rielta Ladoga MK-RK Manual de usuario

Mirion Technologies

Mirion Technologies ACCURAD PRD Manual de usuario

Bosch

Bosch DS835 Manual de usuario

DBI SALA

DBI SALA EZ Stop Manual del operador

Lamptime

Lamptime ST05C Manual de usuario

Ubiquiti

Ubiquiti MFI-MSC Manual de usuario

Subsite

Subsite 910R Instrucciones de instalación

Satel

Satel OPAL Pro Manual de usuario

Aleph

Aleph XC-1XTEU Manual de usuario

Pima

Pima LARIS QUAD Manual de usuario