Pepperl+Fuchs KCD2-UT2-1 Manual de usuario

ISO9001

Functional Safety

Temperature Converter

KCD2-UT2-(Ex)1, HiC2081

PROCESS AUTOMATION

MANUAL

With regard to the supply of products, the current issue of the following document is applicable: The General Terms of

Delivery for Products and Services of the Electrical Industry, published by the Central Association of the Electrical

Industry (Zentralverband Elektrotechnik und Elektroindustrie (ZVEI) e.V.) in its most recent version as well as the

supplementary clause: "Expanded reservation of proprietorship"

Functional Safety KCD2-UT2-(Ex)1, HiC2081

Content

2018-02

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.1 Content of this Document. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.3 Symbols Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2 Product Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.4 Standards and Directives for Functional Safety . . . . . . . . . . . . . . . . . . 8

3 Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.1 System Structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.2 Assumptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.3 Safety Function and Safe State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.4 Characteristic Safety Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.5 Useful Life Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4 Mounting and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.1 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

5 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5.1 Proof Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5.2 Proof Test Procedure for KCD2-UT2-(Ex)1 . . . . . . . . . . . . . . . . . . . . . 15

5.3 Proof Test Procedure for HiC2081 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

6 Maintenance and Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

7 List of Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

2018-02

Functional Safety KCD2-UT2-(Ex)1, HiC2081

Introduction

1Introduction

1.1 Content of this Document

This document contains information for usage of the device in functional safety-related

applications. You need this information to use your product throughout the applicable stages of

the product life cycle. These can include the following:

• Product identification

• Delivery, transport, and storage

• Mounting and installation

• Commissioning and operation

• Maintenance and repair

• Troubleshooting

• Dismounting

• Disposal

The documentation consists of the following parts:

• Present document

• Instruction manual

•Manual

•Datasheet

Additionally, the following parts may belong to the documentation, if applicable:

• EU-type examination certificate

• EU declaration of conformity

• Attestation of conformity

• Certificates

• Control drawings

• FMEDA report

• Assessment report

• Additional documents

For more information about Pepperl+Fuchs products with functional safety, see www.pepperl-

fuchs.com/sil.

Note!

This document does not substitute the instruction manual.

Note!

For full information on the product, refer to the instruction manual and further documentation

on the Internet at www.pepperl-fuchs.com.

Functional Safety KCD2-UT2-(Ex)1, HiC2081

Introduction

2018-02

1.2 Safety Information

Target Group, Personnel

Responsibility for planning, assembly, commissioning, operation, maintenance, and

dismounting lies with the plant operator.

Only appropriately trained and qualified personnel may carry out mounting, installation,

commissioning, operation, maintenance, and dismounting of the product. The personnel must

have read and understood the instruction manual and the further documentation.

Intended Use

The device is only approved for appropriate and intended use. Ignoring these instructions will

void any warranty and absolve the manufacturer from any liability.

The device is developed, manufactured and tested according to the relevant safety standards.

Use the device only

• for the application described

• with specified environmental conditions

• with devices that are suitable for this safety application

Improper Use

Protection of the personnel and the plant is not ensured if the device is not used according to

its intended use.

2018-02

Functional Safety KCD2-UT2-(Ex)1, HiC2081

Introduction

1.3 Symbols Used

This document contains symbols for the identification of warning messages and of informative

messages.

Warning Messages

You will find warning messages, whenever dangers may arise from your actions. It is

mandatory that you observe these warning messages for your personal safety and in order to

avoid property damage.

Depending on the risk level, the warning messages are displayed in descending order as

follows:

Informative Symbols

Action

This symbol indicates a paragraph with instructions. You are prompted to perform an action or

a sequence of actions.

Danger!

This symbol indicates an imminent danger.

Non-observance will result in personal injury or death.

Warning!

This symbol indicates a possible fault or danger.

Non-observance may cause personal injury or serious property damage.

Caution!

This symbol indicates a possible fault.

Non-observance could interrupt the device and any connected systems and plants, or result

in their complete failure.

Note!

This symbol brings important information to your attention.

Functional Safety KCD2-UT2-(Ex)1, HiC2081

Product Description

2018-02

2 Product Description

2.1 Function

KCD2-UT2-1

This signal conditioner provides the galvanic isolation between field circuits and control

circuits.

The device converts RTD input signals or thermocouple input signals on the field side to

0/4 mA ... 20mA signals on the control side.

The removable terminal block KC-CJC-** is available for thermocouples when internal cold

junction compensation is desired.

A fault is indicated by an LED and by user-configured fault indication outputs.

If the device is operated via Power Rail, additionally a collective error message is available.

The device is easily configured by the use of the PACTware configuration software.

The device is mounted on a 35 mm DIN mounting rail according to EN 60715.

KCD2-UT2-Ex1

This isolated barrier is used for intrinsic safety applications.

The device converts RTD input signals or thermocouple input signals in the hazardous area to

0/4 mA ... 20mA signals in the safe area.

The removable terminal block KC-CJC-** is available for thermocouples when internal cold

junction compensation is desired.

A fault is indicated by an LED and by user-configured fault indication outputs.

If the device is operated via Power Rail, additionally a collective error message is available.

The device is easily configured by the use of the PACTware configuration software.

The device is mounted on a 35 mm DIN mounting rail according to EN 60715.

HiC2081

This isolated barrier is used for intrinsic safety applications.

This device accepts thermocouples (TC), millivolts, potentiometers, or resistance temperature

detectors (RTD) from a hazardous area and converts them to an isolated, linearized analog

output in the safe area.

The output can be selected as a current source or current sink with a switch.

Line fault detection of the field circuit is indicated by a red LED and an output on the fault bus.

The fault conditions are monitored via a Fault Indication Board.

The device is easily configured by the use of the PACTware configuration software.

This device mounts on a HiC Termination Board.

2018-02

Functional Safety KCD2-UT2-(Ex)1, HiC2081

Product Description

2.2 Interfaces

The device has the following interfaces.

• Safety relevant interfaces: input, output

• Non-safety relevant interfaces: programming socket, collective error message output

2.3 Marking

2.4 Standards and Directives for Functional Safety

Device-specific standards and directives

System-specific standards and directives

Note!

For corresponding connections see datasheet.

Pepperl+Fuchs GmbH

Lilienthalstraße 200, 68307 Mannheim, Germany

Internet: www.pepperl-fuchs.com

KCD2-UT2-1, KCD2-UT2-Ex1, HiC2081 Up to SIL 2

Functional safety IEC/EN 61508, part 2, edition 2010:

Functional safety of electrical/electronic/programmable electronic

safety-related systems (manufacturer)

Functional safety IEC/EN 61511, part 1 –3, edition 2003:

Functional safety –Safety instrumented systems for the process

industry sector (user)

Functional Safety KCD2-UT2-(Ex)1, HiC2081

Planning

2018-02

3 Planning

3.1 System Structure

3.1.1 Low Demand Mode of Operation

If there are two control loops, one for the standard operation and another one for the functional

safety, then usually the demand rate for the safety loop is assumed to be less than once per

year.

The relevant safety parameters to be verified are:

•thePFD

avg value (average Probability of dangerous Failure on Demand) and the T1

value (proof test interval that has a direct impact on the PFDavg value)

• the SFF value (Safe Failure Fraction)

• the HFT architecture (Hardware Fault Tolerance)

3.1.2 High Demand or Continuous Mode of Operation

If there is only one safety loop, which combines the standard operation and safety-related

operation, then usually the demand rate for this safety loop is assumed to be higher than once

per year.

The relevant safety parameters to be verified are:

•thePFHvalue(Probability of dangerous Failure per Hour)

• Fault reaction time of the safety system

• the SFF value (Safe Failure Fraction)

• the HFT architecture (Hardware Fault Tolerance)

3.1.3 Safe Failure Fraction

The safe failure fraction describes the ratio of all safe failures and dangerous detected failures

to the total failure rate.

SFF = (s+ dd) / (s+ dd + du)

A safe failure fraction as defined in IEC/EN 61508 is only relevant for elements or (sub)systems

in a complete safety loop. The device under consideration is always part of a safety loop but is

not regarded as a complete element or subsystem.

For calculating the SIL of a safety loop it is necessary to evaluate the safe failure fraction of

elements, subsystems and the complete system, but not of a single device.

Nevertheless the SFF of the device is given in this document for reference.

2018-02

Functional Safety KCD2-UT2-(Ex)1, HiC2081

Planning

3.2 Assumptions

The following assumptions have been made during the FMEDA:

• Failure rate based on the Siemens standard SN29500.

• Failure rates are constant, wear is not considered.

• Failures during configuration are not considered.

• The collective error message output is not considered in the FMEDA and in the

calculations.

• Propagation of failures is not relevant.

• External power supply failure rates are not included.

• The collective error message output is not safety relevant.

• The indication of a dangerous failure (via fault bus) is detected within 1 hour by the

programmable logic controller (PLC).

• The safety-related device is considered to be of type Bdevice with a hardware fault

tolerance of 0.

• The device will be used under average industrial ambient conditions comparable to the

classification "stationary mounted" according to MIL-HDBK-217F.

Alternatively, operating stress conditions typical of an industrial field environment similar to

IEC/EN 60654-1 Class C with an average temperature over a long period of time of 40 ºC

may be assumed. For a higher average temperature of 60 ºC, the failure rates must be

multiplied by a factor of 2.5 based on experience. A similar factor must be used if frequent

temperature fluctuations are expected.

• The application program in the programmable logic controller (PLC) is configured to detect

underrange and overrange failures. These failures have been classified as dangerous

detected failures.

SIL 2 Application

• The device shall claim less than 10 % of the total failure budget for a SIL 2 safety loop.

• For a SIL 2 application operating in low demand mode the total PFDavg value of the SIF

(Safety Instrumented Function) should be smaller than 10-2, hence the maximum

allowable PFDavg value would then be 10-3.

• For a SIL 2 application operating in high demand mode the total PFH value of the SIF

should be smaller than 10-6 per hour, hence the maximum allowable PFH value would then

be 10-7 per hour.

• The IEC/EN 61511-1 section 11.4.4 allows devices to be used in applications one SIL

higher than given by table 3 of IEC/EN 61508-2, if the device is proven-in-use. The

assessment and proven-in-use demonstration lead to the result that the device may be

used in applications up to SIL 2. However, it is the responsibility of the end-user to decide

on applying proven-in-use devices.

Otros manuales para KCD2-UT2-1

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Convertidor de medios de Pepperl+Fuchs

Pepperl+Fuchs

Pepperl+Fuchs ENA42HD-S J1939 Series Manual de uso y cuidado

Pepperl+Fuchs

Pepperl+Fuchs WCS Series Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs ENI11HD Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs KFD2-UT2 Series Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs PCV-USB-RS485 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs FieldConnex R-SP-E12 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs PVS58X Series Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs KFD2-UT2 Series Manual de instrucciones

Pepperl+Fuchs

Pepperl+Fuchs KFD2-UT-Ex1 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs WCS Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs K23-SSI/Rx/IU-C Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs ENI58PL-S Series Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs ENI11HD Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs KFD2-HLC-Ex1.D Series Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs KFD2-HLC-Ex1.D Series Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs PS1000-D2-24.10 Manual

Pepperl+Fuchs

Pepperl+Fuchs KFU8-FSSP-1.D-Y Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs EVS58-PZ Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs KFD2-GUT-Ex1.D Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs SLCS Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs K23-SSI/USB/25B-C Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs ES 58 EC Series Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs P 58 Series Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs KFD2-HLC-Ex1.D Series Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario