Pepperl+Fuchs VBA-2E-KE5-IJL Manual de usuario

Spec 2.1

VBA-2E-KE5-IJL/UJL

AS-Interface Analog Module

FACT RY AUT MATI N

MANUAL

With regard to the supply of products, the current issue of the following document is ap-

plicable: The General Terms of Delivery for Products and Services of the lectrical Indus-

try, published by the Central Association of the lectrical Industry (Zentralverband

lektrotechnik und lektroindustrie (ZV I) e.V.) in its most recent version as well as the

supplementary clause: " xpanded reservation of proprietorship"

VBA-2 -K 5-IJL/UJL

1 Introduction................................................................................. 4

1.1 Content of this Document ................................................................... 4

1.2 Target Group, Personnel...................................................................... 4

1.3 Symbols Used ...................................................................................... 5

2 Certificates and Approvals ........................................................ 6

2.1 UL Information...................................................................................... 6

3 Product Description ................................................................... 7

3.1 Intended Use ........................................................................................ 7

3.2 Displays and perating Elements ...................................................... 7

3.3 Connections ......................................................................................... 8

3.4 Automatic Detection of the Sensor Type ........................................... 9

3.5 Resetting the Automatically Detected Sensor Types ....................... 9

4 Installation................................................................................. 10

4.1 Storage and Transport ....................................................................... 10

4.2 Unpacking........................................................................................... 10

4.3 Mounting ............................................................................................. 10

4.4 Connecting AS-Interface/Auxiliary Voltage ..................................... 10

4.5 Connecting the Sensors.................................................................... 11

5 Commissioning......................................................................... 12

5.1 Assigning an Address to the Module............................................... 12

5.2 Slave Profile........................................................................................ 12

5.3 Parameterization ................................................................................ 12

6 Troubleshooting........................................................................ 14

6.1 Causes and Elimination of a Peripheral Fault ................................. 14

6.2 Cause and Elimination of a Channel Fault....................................... 14

6.3 Cause and Elimination of a Sensor Fault......................................... 14

7 Appendix ................................................................................... 15

7.1 Analog Input Module Measuring Ranges ........................................ 15

7.2 Delay Times ........................................................................................ 16

2018-07

VBA-2 -K 5-IJL/UJL

Introduction

1 Introduction

1.1 Content of this Document

This document contains information required to use the product in the relevant phases of the

product life cycle. This may include information on the following:

■

Product identification

■

Delivery, transport, and storage

■

Mounting and installation

■

Commissioning and operation

■

Maintenance and repair

■

Troubleshooting

■

Dismounting

■

Disposal

The documentation comprises the following parts:

■

This document

■

Datasheet

In addition, the documentation may comprise the following parts, if applicable:

■

U-type examination certificate

■

U declaration of conformity

■

Attestation of conformity

■

Certificates

■

Control drawings

■

Instruction manual

■

Other documents

1.2 Target Group, Personnel

Responsibility for planning, assembly, commissioning, operation, maintenance, and

dismounting lies with the plant operator.

Only appropriately trained and qualified personnel may carry out mounting, installation,

commissioning, operation, maintenance, and dismounting of the product. The personnel must

have read and understood the instruction manual and the further documentation.

Prior to using the product make yourself familiar with it. Read the document carefully.

Note!

For full information on the product, refer to the further documentation on the Internet at

www.pepperl-fuchs.com.

VBA-2 -K 5-IJL/UJL

Introduction

2018-07

1.3 Symbols Used

This document contains symbols for the identification of warning messages and of informative

messages.

Warning Messages

You will find warning messages, whenever dangers may arise from your actions. It is mandatory

that you observe these warning messages for your personal safety and in order to avoid

property damage.

Depending on the risk level, the warning messages are displayed in descending order as

follows:

Informative Symbols

Action

This symbol indicates a paragraph with instructions. You are prompted to perform an action or

a sequence of actions.

Danger!

This symbol indicates an imminent danger.

Non-observance will result in personal injury or death.

Warning!

This symbol indicates a possible fault or danger.

Non-observance may cause personal injury or serious property damage.

Caution!

This symbol indicates a possible fault.

Non-observance could interrupt the device and any connected systems and plants, or result in

their complete failure.

Note!

This symbol brings important information to your attention.

2018-07

VBA-2 -K 5-IJL/UJL

Certificates and Approvals

2 Certificates and Approvals

2.1 UL Information

Technical Data and Environmental Conditions

This device is for indoor use only.

This device may be operated in altitudes up to 2000 m.

The ambient temperature range is from -25 °C to +70 °C.

The device must be installed in accordance with applicable national laws and regulations.

If the device is used in a manner not specified by the manufacturer, the protection provided by

the equipment may be impaired.

The device must be installed in a switch cabinet or switch box that meets protection class IP54

as a minimum.

VBA-2 -K 5-IJL/UJL

Product Description

2018-07

3 Product Description

3.1 Intended Use

The VBA-2 -K 5-IJL/UJL is an analog module for connecting 0 V 10 V or 0/4 mA 20 mA

sensors to the AS-Interface network. Data conversion and data transfer are provided

asynchronously according to AS-Interface profile 7.3. The data is converted internally at a 16

bit resolution. The analog module features two analog inputs that can be used as either a

current or a voltage input. The sensors are supplied with power via the AS-Interface or auxiliary

voltage.

3.2 Displays and Operating lements

Figure 3.1 Displays and operating elements

The VBA-2 -K 5-IJL/UJL analog module is equipped with the following indicators and

operating elements:

LED Indicators

Description Function

FAULT L D Fault indication; L D red

red: communication fault or address is 0

red, flashing: peripheral fault

INT L D Internal input voltage active; green L D

PWR L D AS-Interface voltage; L D green

green: voltage OK

green, flashing: address 0 or peripheral fault

AUX L D xt. auxiliary voltage U

AUX

; dual green/red L D

green: voltage OK

red: voltage reversed

IN1 L D

IN2 L D

Status of input signal; yellow L D

Yellow: input value within measuring range (see note below)

Flashing yellow: wire break or input value outside of measuring range

Off: channel deactivated

AUX

INT

PWR

FLT

AUX

INT

ADDR

Note!

The IN L D lights up continuously if the corresponding input is configured as a current input.

For inputs in voltage mode, the corresponding IN L D flashes, going out briefly and then

illuminating for a longer period. See chapter 7.

2018-07

VBA-2 -K 5-IJL/UJL

Product Description

Switch

3.3 Connections

Figure 3.2

The analog module has the following connections:

Description Function

INT/AUX switch Set to INT: inputs powered via the AS-Interface (max. 100 mA)

Set to AUX: inputs powered via auxiliary voltage (max. 600 mA)

Warning!

Only use the switch when de-energized

Only adjust the INT/AUX switch if the module is not supplied via the AS-Interface (INT) or the

auxiliary voltage (AUX)!

Name Description

ADDR Addressing socket, extra-low-voltage switch socket, Ø 1.3 mm

IU+1/IU-1

IU+2/IU-2

Voltage at analog inputs

II1

II2

Current at analog inputs

L+ Sensor supply

GND Reference potential of inputs + sensors

1CH Jumper to the input configuration

ASI+

ASI-

AS-Interface; both ASI+ terminals and both ASI- terminals are

bridged in the terminal block.

AUX+

AUX-

Auxiliary voltage; both AUX+ terminals and both AUX- terminals

are bridged in the terminal block.

IU-1

GND

IU-2

GND

1CH

GND

AUX+

AUX-

ASI+

ASI-

ADDR

IU+1

L+

IU+2

L+

GND

II1

L+

II2

L+

AUX+

AUX-

ASI+

ASI-

VBA-2 -K 5-IJL/UJL

Product Description

2018-07

3.4 Automatic Detection of the Sensor Type

ach of the two input channels can be operated either as a current or a voltage input. The

analog input module automatically detects the type of sensor connected. 0 V  10 V or 0/4 

20 mA measurement sensors can be connected as sensor types. The automatic detection

process occurs after the device is switched on. The detected sensor type is saved in the non-

volatile memory and reactivated when the device is switched on again.

The valid signal values that ensure unambiguous detection of the type of sensor connected

are:

■

Voltage: 1 ... 11.5 V

■

Current: 1 ... 23 mA

If the module cannot clearly establish which sensor type is connected, the last detected sensor

type is provisionally activated. For example, the module may not detect which sensor type is

connected if the signal values are not within the specified thresholds or if two different sensor

types are simultaneously applied to one channel.

A specific sensor type is finally activated when the signal values measured are within the

specified thresholds.

3.5 Resetting the Automatically Detected Sensor Types

Any sensor types saved through automatic detection are reset when the input configuration of

the module is manually changed. For this, there are two available options:

1. Switch off the module power supply. Place or remove the jumper between 1CH and GND,

then switch on the supply voltage again.

2. Change the status of parameter P1 or P3 (see chapter 5.3). In this case, it is not necessary

to switch the supply voltage off and on.

Repeat this process if necessary to return to the required input configuration.

Note!

Switching Off the Second Channel

Figure 3.3 Jumper for switching off input channel 2

Input channel 2 can be deactivated using a jumper between the GND and 1CH connections or

using parameter P1. The jumper has priority. If no jumper is set and P1 = 1, then both channels

are active.

GND

1CH

GND

Note!

Any change made to the input configuration via a jumper between 1CH and GND is only

detected once the supply voltage is switched on. Changes made via parameter P1 and P3 can

also be implemented during ongoing operation. See chapter 5.3.

Do not connect the 1CH and GND connections to external potentials. The length of the

jumpers must not exceed 5 cm.

Note!

If you connect two different sensor types to one channel simultaneously, fault-free operation is

not guaranteed. The module will not be damaged by this.

2018-07

VBA-2 -K 5-IJL/UJL

Installation

4 Installation

4.1 Storage and Transport

For storage and transport purposes, package the unit using shockproof packaging material

and protect it against moisture. The best method of protection is to package the unit using the

original packaging. Furthermore, ensure that the ambient conditions are within allowable range.

4.2 Unpacking

Check the product for damage while unpacking. In the event of damage to the product, inform

the post office or parcel service and notify the supplier.

Retain the original packaging in case the device must be stored or shipped again at a later date.

Should you have any questions, please contact Pepperl+Fuchs.

4.3 Mounting

Mount the module by snapping it onto a 35 mm DIN rail in compliance with N 50022.

Unlocking Terminal Blocks

Proceed as follows to unlock and eject terminal blocks:

Figure 4.1 Unlocking terminals

4.4 Connecting AS-Interface/Auxiliary Voltage

2 terminals each are avilable for ASI+, ASI-, AUX+ and AUX- in order to ease the looping of

these lines. ach of these terminal pairs is bridged in the terminal block. This is why the

connection remains intact even though the terminal block has been separated from the

module.

1. Lift the label carrier upwards.

2. Guide a suitable screwdriver through the eye on the ejector and then:

■

Insert the blade of the screwdriver on the bottom of the foot bolt.

■

Then pull on the handle of the screwdriver in the direction indicated.

3. Remove the terminal block.

Warning!

Note the permitted operating temperature

The permitted operating temperature of the cables connected to the terminal block must be at

least +80 ° C!

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Pepperl+Fuchs

Pepperl+Fuchs

Pepperl+Fuchs VBA-4E-G11-I-F Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs VBA-4E4A-G20-ZEJ/M3L-P9 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs IC-KP2-1HB6-V15B Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs 7500 Series Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs LAL-SRW series Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs VBA-4E-KE5-IL Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs IC-KP2-2HB6-V15B Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs VU121 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs SC4-2 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs VU121 Guía de referencia

Pepperl+Fuchs

Pepperl+Fuchs WCS DG310 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs VAA-2E2A-KE1-S/E2 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs IDENT-M System V MVI-F57-2HB12 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs ICE1-8IOL-S2-G60L-V1D Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs VBA-4E3A-G20-ZEL/M1L-P6 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs SC2-2 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs VLX-F231-B6 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs PSU-IDM160-BD-1D-J1-N0 Series Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs SIL KFD0-RSH-1 Guía del usuario

Pepperl+Fuchs

Pepperl+Fuchs ICE11-8IOL-G60L-V1D Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs WCS-EIG410 Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs IC-KP2-1HB6-2V15B Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs ICA-8DIO4M1-G20-IO Manual de usuario

Pepperl+Fuchs

Pepperl+Fuchs WCS-ECG410 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario