PEERLESS Solid-Point PLCM 1 CP Guía
ISSUED:08-21-02 SHEET #: 200-9405-9 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
1 of 6
Read instruction sheet before you start installation and assembly.
Model:PLCM 1 CP,
PLCM UNL CP
Maximum Load Capacity:
225 lb (102.3 kg)
Installation and Assembly -Solid•Point™Flat Panel Straight
Column Ceiling Mount
R
This product is intended for use with UL
Listed products and must be installed by a
qualified professional installer.
TABLE OF CONTENTS
Installations
InstallingFlatPanelStraightColumnCeilingMount toceiling
pages 3-4
Applications
Installationofplasma screensand
30" or larger LCD screens ...........................................page 5
Installationof smallLCDscreens .................................page 6
• Installer must verify that the ceiling will safely support
thecombined weightofallattachedequipment and
hardware.
WARNING
ISSUED:08-21-02 SHEET #: 200-9405-9 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
2 of 6
D
F
A
Note: Some parts may not appear exactly as illustrated.
HI
C
E
G
J
Fasteners
B
K
L
M
PLCM 1 CP
PLCM UNL CP
Description Qty Part #
Aceiling arm box 1 201-1062
Btilt bracket 1 200-1552
C33" extension column 1 139-1088
Dretaining collar 1 1800-375
EM5 x .8 x 10 mm penta-pin™ screw 5 505-9010
F2.875 OD x 2.125 ID x .062 H fiber washer 1 540-9432
GM10 x 1.5 x 15 mm penta-pin screw 8 520-9263
HM10 x 2" penta-pin tool 1 520-9260
IM5 x 1" penta-pin tool 1 520-9249
JM5 x .8 x 8 mm phillips Type F screw 4 520-1167
Kceiling plate 1 128-1039
Lceiling plate end cap 2 2PT-22CA01D
M#14 x 2.5" hex head phillips wood screw 4 5S1-015-C03
Before you begin, make sure all parts shown are included with your product.
PARTS LIST
ISSUED:08-21-02 SHEET #: 200-9405-9 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
3 of 6
L
K
For Wood Joist Finished Ceiling, Exposed
Wood Joists, or Wood Beam Ceiling. Drill four
5/32" (4 mm) dia. holes to a minimum depth of
2.5"(64mm) INTOJOIST CENTERS. Attach
ceiling plate (K) with four #14 x 2.5" (6 mm x 65
mm) wood screws (M) using a 3/8"(10 mm) socket
wrench.Tighten woodscrews (M)soceiling plate
is firmly attached. Snap end caps (L) into place.
For Concrete Ceilings drillfour 5/16"(8 mm)
dia. holes to a minimum depth of 1 3/4" (45
mm). Attach ceiling plate (K) using concrete
expansionanchorsas shownin 1-1and 1-2.
Then snap end caps (L) into place.
Align hole in ceiling plate with hole in ceiling.
Gentlyhammerinconcreteanchor.
Use a 10 mm wrench to tighten concrete
anchor to 80 in • lb (9 N.M.) maximum torque
toexpand anchors.
FORPRODUCT SAFETYUSE ONLYRAWL™
#5005OR HILTI™HL814CONCRETE
ANCHORS.Order accessorykit #ACC 210
which contains four .312 x 1.625
(8 mm x 41 mm) concrete expansion
anchors.
L
K
M
CONCRETE
PLASTER/
DRYWALL
ACC210
• Tighten wood screws so that ceiling plate is firmly
attached,but donot overtighten.Overtightening can
damagescrews, greatlyreducing theirholding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the
center of the joists. The use of an "edge to edge" stud
finderis highlyrecommended.
WARNING
• Always attach concrete expansion anchors directly to
load-bearingconcrete.
• Neverattach concreteexpansion anchorstoconcrete
coveredwith plaster,drywall,orotherfinishingmaterial.
WARNING
ISSUED:08-21-02 SHEET #: 200-9405-9 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
4 of 6
Threadsupportpipe(C)intothreadedfittinginceilingplate(K).Tighten-fourorfivecompleteturns-leavingslot
aligned with one small hole in the side of the ceiling plate threaded fitting. Insert and tighten one M5 x .8 x 10 mm
penta-pin screw (E) as shown. Use the M5 penta-pin tool (I) to tighten screw. BY HAND, insert four M10 x 1.5 x
15 mm penta-pin screws (G)intothreaded holesinthe sidesof ceiling armbox (A). Leaveapproximately 1/4”of
exposedthread.Slideceilingarmbox (A)andfiberwasher(F)ontoend ofsupportpipe(C).Threadretainingcollar
(D)ontothreaded endof supportpipe(C). Tighten -four orfivecomplete turns. Slideceiling arm box(A) downso
that it is on top of retaining collar (D). Insert and tighten one M5 x .8 x 10 mm penta-pin screw (E) into retaining
collar (D) as shown. Insert one M5 penta-pin screw (E) through the tab on the back of ceiling arm box (A). Use
M5 penta-pin tool (I) to tighten screw just enough to stabilize support pipe (C).
E
C
C
A
F
D
G
1/4”
G
E
E
K
BACKOF CEILING
ARMBOX
D
ISSUED:08-21-02 SHEET #: 200-9405-9 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
5 of 6
Hang tilt bracket (B) onto ceiling arm box
(A).Adjust tilt as desired and tighten four
M10 x 1.5 x 15 mm penta-pin screws (G)
securelyusingM10penta-pintool (H).
B
A
G
Attach tilt bracket (B) to adapter plate using four M10 x 15 mm penta-pin screws (G)
inaccordance withappropriate drawingbelow. Tighten usingM10 penta-pintool (H).
G
B
Note: Refertoadapter plateinstruction sheetfor attachmentofadapter plateto plasma beforeproceeding with step3.
LANDSCAPE
LANDSCAPE
LANDSCAPE
B
A
G
B
G
ADAPTERPLATE
ADAPTERPLATE
PLASMASCREEN
PLASMASCREEN
Note: Screenand adapter
platemay appeardifferent
thanillustrated.
• For a safe assembly be sure to fully tighten four
screws(G).
WARNING
PORTRAIT
(Not to be used with UNL models)
PORTRAIT
(Not to be used with UNL models)
• Donot mountPLCMUNL-CPinportrait orientation.
MountingPLCM UNL-CPin portraitorientation may
resultin productfailure.
WARNING
ISSUED:08-21-02 SHEET #: 200-9405-9 02-16-06
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
6 of 6
ADAPTERBRACKET
B
J
Attach tilt bracket (B) to adapter bracket using four M5 x 8 mm phillips screws (J).
Note: Do not use M5 x 6 mm screws that are included with the adapter bracket.
Note: Refertoadapterbracketinstruction sheetfor attachmentof adapterbracket toLCDscreen before
proceedingwithstep3.
Hang tilt bracket (B) onto ceiling arm box (A).Adjust tilt as desired and tighten four
M10 x 1.5 x 15 mm penta-pin screws (G) securely using M10 penta-pin tool (H).
B
A
G
©2004PeerlessIndustries,Inc. Allrightsreserved.
PeerlessisaregisteredtrademarkofPeerlessIndustries, Inc.
Solid•PointisatrademarkofPeerlessIndustries,Inc.
Allother brand and productnames are trademarks or registered trademarks oftheir respective owners.
Note:Screen andadapter
platemay appeardifferent
thanillustrated.
LCDSCREEN
• For a safe assembly be sure to fully tighten four
screws(G).
WARNING
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Rack y soporte de PEERLESS
PEERLESS
PEERLESS DS-VW760 and assembly Guía
PEERLESS
PEERLESS CMJ 470W Guía
PEERLESS
PEERLESS SF 24D Guía
PEERLESS
PEERLESS WBK100-W Guía
PEERLESS
PEERLESS SP850-UNLP-GB Guía
PEERLESS
PEERLESS SUT632P Guía
PEERLESS
PEERLESS Paramount PF660 Guía
PEERLESS
PEERLESS Vision Point LCFS 100 Guía
PEERLESS
PEERLESS Paramount PS200 Guía
PEERLESS
PEERLESS SOLID POINT PLCM 1 Manual de instrucciones
PEERLESS
PEERLESS ACC517 Guía
PEERLESS
PEERLESS PARAMOUNT PSP2-S Guía
PEERLESS
PEERLESS PARAMOUNT PA730 Guía
PEERLESS
PEERLESS WSP700 Manual de instrucciones
PEERLESS
PEERLESS IMC 18 Guía
PEERLESS
PEERLESS Paramount PA760 Guía
PEERLESS
PEERLESS SmartMount RTFPA45 Guía
PEERLESS
PEERLESS PLT BLK Guía
PEERLESS
PEERLESS HDS-S Guía
PEERLESS
PEERLESS SUF650P and assembly Guía
