peerless-AV KIL642 Manual de usuario
12013-09-20 #:150-9009-1
ENG
BLACK
KIL640
KIL642
KIL646
KIL647
SILVER
KIL640-S
KIL642-S
KIL646-S
KIL647-S
22013-09-20 #:150-9009-1
ENG - Do not begin to install product until you have read and understood the instructions and warnings
contained in this user guide. This product is designed to be installed on wood stud, solid concrete or cinder
block walls. Hardware is included for wood stud, solid concrete and cinder block installation. Before installing
make sure the supporting surface will support the combined load of the equipment and hardware. Screws must
be tightly secured. Do not overtighten screws or damage can occur and product may fail. Never exceed the
Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift and position
equipment. This product is intended for indoor use only. Use of this product outdoors could lead to product
failure or personal injury. To reduce the risk of electric shock or re, do not expose product to water or moisture.
Be sure power cord is routed so that it will not be tripped on, stepped on, or pinched by heavy items. Avoid
overloading electrical outlets or extension cords. Always disconnect the power cord from the power outlet
when installing, servicing, or not using the product for an extended period of time. Do not block ventilation
slots or fan exhaust on product. Blocking airow could damage product. Arrange product to allow air to ow
freely around product. Keep product away from direct sunlight or any source of heat. For support please call
800-4-SIGNAGE.
WARNING
Symbols
ENG
WARNING
ENG
#
Skip to step.
ENG
x3
Screws must get at least three
full turns and t snug.
ENG
Do not overtighten screws.
ENG
1
2
ENG To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
+1/2
4
3
32013-09-20 #:150-9009-1
Tools Needed for Assembly.
ENG
5/16"
(8mm)
5/32"
(4mm)
3/8"
(10mm)
42013-09-20 #:150-9009-1
Parts (Before beginning, make sure you have all parts shown below).
ENG
A (1)
Kiosk
J (2)
key
B (8)
M5 x 12 mm
C (8)
M5 x 25 mm
D (8)
M6 x 12 mm
E (8)
M6 x 25 mm
M5/M4/M6 washer
H (8)
M8 x 12 mm
F (8)
M8 x 25 mm
G (8)
spacer
I (8)
K (1)
T- wrench
M (4)
#14 x 2-1/2" wood screw
L (4)
8mm concrete anchor
Parts List KIL640
KIL640S
Part #
KIL642
KIL642S
Part #
KIL646
KIL646S
Part #
KIL647
KIL647S
Part #
Description Qty
AKiosk BLK
Kiosk SLV
1 xxx-xxxx xxx-xxxx xxx-xxxx xxx-xxxx
BM5 x 12mm 4 520-1027 520-1027 520-1027 520-1027
CM5 X 25mm 4 520-9543 520-9543 520-9543 520-9543
DM6 x 12mm 4 520-1128 520-1128 520-1128 520-1128
EM6 x 25mm 4 520-1208 520-1208 520-1208 520-1208
FM8 x 12mm 4 520-9571 520-9571 520-9571 520-9571
GM8 x 25mm 4 520-1031 520-1031 520-1031 520-1031
HM5/M4/M6 multi washer 4 580-1398 580-1398 580-1398 580-1398
ISpacer 4 540-1059 540-1059 540-1059 540-1059
JKey 2 565-0049A 565-0049A 565-0049A 565-0049A
KT-Wrench 1 560-1718 560-1718 560-1718 560-1718
Lconcrete anchor 4 590-0320 590-0320 590-0320 590-0320
Mwood screw 4 5S1-015-C04 5S1-015-C04 5S1-015-C04 5S1-015-C04
52013-09-20 #:150-9009-1
1
J (2)
A
62013-09-20 #:150-9009-1
2
A
A
72013-09-20 #:150-9009-1
3
3a-1
Use stud nder to locate and
mark stud center lines.
ENG
3b3a-1
Wood stud wall.
ENG Concrete/Cinder block.
ENG
82013-09-20 #:150-9009-1
3a-2
Level wallplate. Mark mounting holes on stud
center lines.
ENG
A
92013-09-20 #:150-9009-1
3a-3
Mounting hole must center on stud.
ENG
5/32"
(4mm)
Drill mounting holes into supporting surface
(2.5" (64 mm) minimum depth required).
ENG
2.5"
(64mm)
5/32"
(4mm)
M (4)
4
3a-4
3/8"
(10mm)
A
10 2013-09-20 #:150-9009-1
ENG • When installing Peerless wall mounts on a concrete wall, the wall must be at least 8" thick with a minimum
compressive strength of 2000 psi.
• When installing Peerless wall mounts on a cinder block wall, the cinder blocks must meet ASTM C-90
specications and have a minimum nominal width of 8". Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" (25 mm) minimum from the side of the block. It is suggested that a standard electric
drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole
when entering a void or cavity.
• Never attach expansion anchors to concrete or cinder block covered with plaster, drywall or other nishing
material.
WARNING
3b-1
Level wallplate. Mark mounting holes. Make
sure mountinting holes are 1" off motor joints.
ENG
1"
(25mm)
A
Este manual sirve para los siguientes modelos
7
Tabla de contenidos
Otros manuales de Rack y soporte de peerless-AV
peerless-AV
peerless-AV PSTA-028 Guía
peerless-AV
peerless-AV MOD-AWM2 Manual de usuario
peerless-AV
peerless-AV ESHV30 Manual de usuario
peerless-AV
peerless-AV ESA746PU Guía
peerless-AV
peerless-AV CMJ470 Manual de usuario
peerless-AV
peerless-AV PRS-EXA Guía
peerless-AV
peerless-AV DS-VW765-LAND Manual de usuario
peerless-AV
peerless-AV DST980-3 Manual de usuario
peerless-AV
peerless-AV DS-VW765-LQR Manual de usuario
peerless-AV
peerless-AV ACC-MB10 Manual de usuario
peerless-AV
peerless-AV DS-VW765-PQR Manual de usuario
peerless-AV
peerless-AV PJF3-EXA Manual de usuario
peerless-AV
peerless-AV IM746P Manual de usuario
peerless-AV
peerless-AV SmartMount SF670-AB Manual de usuario
peerless-AV
peerless-AV PWV240/BK Guía
peerless-AV
peerless-AV PA740-S Guía
peerless-AV
peerless-AV SUA751PU Manual de usuario
peerless-AV
peerless-AV SR575K Manual de usuario
peerless-AV
peerless-AV ACC975 Manual de usuario
peerless-AV
peerless-AV ACC976 Manual de usuario
