Peerless-AV PA740-S Guía

Installation and Assembly:

Articulating Wall Mount for 22" - 40" (56 - 102 cm) Flat

Panel Displays

Models: PA740, PA740-S

Features:

• Fits 22" - 40" (56 - 102 cm) ﬂat panel displays

• Two tensionable pivot points for extensive adjustment of

viewing angle

• VESA®75/100/200 x 100/200 x 200 compatible

• Frees up space by folding ﬂat against the wall

ISSUED: 01-27-08 SHEET #: 095-9283-8 01-25-12

2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.com

Max UL Load Capacity:

80 lb (36 kg)

2 of 46 ISSUED: 01-27-08 SHEET #: 095-9283-8 01-25-12

Table of Contents

Parts List.................................................................................................................................................................................3

Installation to Wood Stud Wall................................................................................................................................................5

Installation to Solid Concrete and Cinder Block .....................................................................................................................6

Attaching Adapter Plate to Display with VESA®Mounting Pattern .........................................................................................7

Installing to Peerless PLP Model Adapter Bracket .................................................................................................................8

Cord Management................................................................................................................................................................10

NOTE: Read entire instruction sheet before you start installation and assembly.

Tools Needed for Assembly

• stud ﬁnder ("edge to edge" stud ﬁnder is recommended)

• phillips screwdriver

• drill

• 5/16" (8 mm) bit for concrete and cinder block wall

• 5/32" (4 mm) bit for wood stud wall

• level

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum UL Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁnder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁrmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

•Wood Beam Included

•Solid Concrete Included

•Cinder Block Included

•Metal Stud Do not attach except with Peerless Metal Stud Accessory Kit

(not evaluated by UL)

•Brick Contact Qualiﬁed Professional (not evaluated by UL)

•Other or unsure? Contact Qualiﬁed Professional

WARNING

3 of 46 ISSUED: 01-27-08 SHEET #: 095-9283-8 01-25-12

PA740 PA740-S

Description Qty. Part

Part

Awall mount assembly 1095-P1704 095-4704

Bconcrete anchor 2 590-0320 590-0320

C#14 x 2-1/2" flat head wood screw 2 520-1202 520-2165

D1/4-20 x .5" knob 1560-1162 560-1162

EM4 x 10 mm phillips screw 4 504-9012 520-2027

FM6 x 12 mm phillips screw 4 520-1128 520-2039

GM6 x 20 mm phillips screw 4 520-9402 520-2040

HM8 x 10 mm phillips screw 4 520-1605 520-2605

IM5 x 6 mm phillips screw 4 520-1023 520-2214

J#10 flat washer 4 540-9400 540-9442

Khook plate 1 095-P1561 095-4561

Ladapter plate 1 095-P1721 095-4721

Mcable tie 3560-9711 560-2004

Ncable tie anchor 3590-1290 590-1290

O8-32 x 1/4" flat head screw 3520-1622 520-2622

Pspacer 4 590-5005 590-5003

Parts List

Parts may appear slightly different than illustrated.

Before you begin, make sure all parts shown are included with your product.

MN OP

FG HE

4 of 46 ISSUED: 01-27-08 SHEET #: 095-9283-8 01-25-12

Loosen 1/4-20 x 1/2" screws to remove hook bracket (K) from wall mount assembly prior to installation.

1/4-20 X 1/2"

SCREWS

5 of 46 ISSUED: 01-27-08 SHEET #: 095-9283-8 01-25-12

Installation to Wood Stud Wall

Using a stud ﬁnder, locate and mark the edges of the wood stud used in mounting this product. Use of an edge to

edge stud ﬁnder is highly recommended. Use a level to draw a vertical line down the center of the stud. Use wall

plate as template to mark center of holes along the vertical line. Drill two 5/32" (4 mm) dia. holes 2.5" (64 mm)

deep. Attach wall mount (A) to wall using two #14 x 2.5" ﬂat head wood screws (C) as shown.

Skip to step 3.

WOOD

STUD

WALL PLATE

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁrmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁnder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs.

Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).

WARNING

6 of 46 ISSUED: 01-27-08 SHEET #: 095-9283-8 01-25-12

Installation to Solid Concrete and Cinder Block

Level and use wall plate as template to mark center

of holes. Drill two 5/16" (8 mm) dia. holes to a

minimum depth of 2.5" (64 mm). Insert anchors (B)

in holes ﬂush with wall. Place wall mount (A) over

anchors and secure with wood screws (C). Make

sure wall mount is level, and tighten all fasteners.

WALL PLATE

SOLID CONCRETE CINDER BLOCK

CUTAWAY VIEW

INCORRECT CORRECT

wall

plate

wall

plate

plaster/

drywall plaster/

drywall

concrete concrete

Drill holes and insert anchors (B).

Place plate (A) over anchors (B) and secure with screws (C).

Tighten all fasteners.

concrete

surface

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual

concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount

in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM

C-90 speciﬁcations. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware

and components.

WARNING

• Tighten screws so that wall plate is ﬁrmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Always attach concrete expansion anchors directly

to load-bearing concrete.

• Never attach concrete expansion anchors to

concrete covered with plaster, drywall, or other

ﬁnishing material. If mounting to concrete surfaces

covered with a ﬁnishing surface is unavoidable (not

evaluated by UL), the ﬁnishing surface must be

counterbored as shown below. Be sure concrete

anchors do not pull away from concrete when

tightening screws. If plaster/drywall is thicker than

5/8" (16 mm), custom fasteners must be supplied by

installer (not evaluated by UL).

WARNING

7 of 46 ISSUED: 01-27-08 SHEET #: 095-9283-8 01-25-12

FOR VESA 200 x 100 MOUNTING PATTERN:

Choose hole pattern as shown below. Attach

adapter plate (L) to back of display using four

M4 or M6 screws (E, F, G) as shown below.

Attach hook bracket (K) onto adapter plate (L) using

four M5 x 6 mm screws (I) and #10 washers (J) as

shown.

Attaching Adapter Plate to Display with VESA 200 or 200 x 100 Mounting Pattern

NOTE: For VESA 75 mm and 100 mm patterns, see

following page.

EF, G, H

Attach adapter plate (L) to back of display with four

M4 screws (E) using hole pattern shown below.

Attach adapter plate (L) to back of display with four M6

or M8 screws (F, G, H) using hole pattern shown below.

E, F, G

• If screws don't get three complete turns in the

display inserts or if screws bottom out and bracket is

still not tightly secured, damage may occur to display

or product may fail.

WARNING

FOR VESA 200 MOUNTING PATTERN USING

M4 SCREWS:

FOR VESA 200 MOUNTING PATTERN USING

M6 OR M8 SCREWS:

8 of 46 ISSUED: 01-27-08 SHEET #: 095-9283-8 01-25-12

Attaching Hook Bracket to Display with VESA 75 or 100 Mounting Pattern

FOR VESA®75 MOUNTING PATTERN:

Choose hole pattern as shown below. Attach hook

bracket (K) to back of display using four

M4 x 10 mm screws (E) as shown below.

FOR VESA 100 MOUNTING PATTERN:

Choose hole pattern as shown below. Attach hook

bracket (K) to back of display using four

M4 x 10 mm screws (E) as shown below.

For display compatibility please refer to the ﬂat panel display interface list on our website www.peerlessmounts.com

or call customer care for a display speciﬁc adapter bracket LC or PLP models (not evaluated by UL).

For Installing to Peerless PLP Model Adapter Plate (not evaluated by UL)

Note: Refer to PLP model adapter plate instruction

sheet for attachment of adapter plate to display.

Note: M5 x 10 mm screws are included with the

PLP model adapter plate.

Attach hook bracket (K) to adapter plate using four

M5 x 10 mm screws.

GENERIC ADAPTER PLATE

M5 X 10 mm SCREW

• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to display or product may fail.

WARNING

9 of 46 ISSUED: 01-27-08 SHEET #: 095-9283-8 01-25-12

Attaching Tilt Knob to Wall Mount (optional)

For tool-less tilt adjustment, replace one 1/4-20 x

1/2" screw with tilt knob (D). Drive one 1/4-20 x 1/2"

screw four turns and then remove. Hand thread tilt

knob (D) into wall mount (A) leaving 1/4" exposed

thread as shown in front view.

NOTE: Be sure four 1/4-20 x 1/2" screws have 1/4"

exposed thread.

• Do not lift more weight than you can handle.

Use additional man power or mechanical lifting

equipment to safely handle placement of the display.

WARNING

• Do not tighten screws with excessive force.

Overtightening can cause damage to mount. Tighten

screws to 20 in. • lb (2.26 N.M.) maximum torque.

• Be careful not to pinch ﬁngers when opening and

closing mount from the wall.

CAUTION

To attach display to wall mount (A), hook tilt bracket

onto four 1/4-20 x 1/2" screws.

Installing and Removing Flat Panel Display

1/4-20 X1/2"

SCREWS

Adjust display to desired tilt (15° forward,

5° backward), then tighten four 1/4-20 x 1/2" screws.

Hold display securely to remove from mount. Loosen four

1/4-20 x 1/2" screws and lift display away to disengage tilt

bracket from mount.

1/4-20 X1/2"

SCREWS

FRONT VIEW

REPLACE LEFT OR RIGHT

1/4-20 x 1/2" SCREW WITH TILT KNOB

1/4"

10 of 46 ISSUED: 01-27-08 SHEET #: 095-9283-8 01-25-12

10-32 x 1/2" screws are pretensioned and require

no adjustment. Rotate display by hand to level

display. Roll bracket allows 2° roll adjustment.

• Do not tighten screws with excessive force. Overtightening can cause damage to mount. Tighten screws

to 40 in. • lb (4.5 N.M.) maximum torque.

CAUTION

1/4-20 X1/2" SCREWS

ROLL BRACKET

Attach cable tie anchor (N) to top or bottom of wall

arm (A) using 8-32 x 1/4" screw (O) as shown.

Secure cables to wall arm (A) using cable tie (M).

Cord Management

CORD

2° ROLL

7-1

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Rack y soporte de peerless-AV

peerless-AV

peerless-AV ACCXT201 Guía

peerless-AV

peerless-AV HLG440-LG(-Q10) Manual de usuario

peerless-AV

peerless-AV DCT Series Manual de usuario

peerless-AV

peerless-AV DS-LED27BDL Series Manual de usuario

peerless-AV

peerless-AV SMARTMOUNT ST660 Manual de usuario

peerless-AV

peerless-AV NEC PD04VW MFS 46 55 Manual de usuario

peerless-AV

peerless-AV DS-C555-3X3 Manual de usuario

peerless-AV

peerless-AV KIP586-3LG-EUK Manual de usuario

peerless-AV

peerless-AV DS-LEDLSAA Series Manual de usuario

peerless-AV

peerless-AV SmartMount XT SFX650 Manual de usuario

peerless-AV

peerless-AV ACC 845 Manual de usuario

peerless-AV

peerless-AV SMARTMOUNT LT SFL670 Manual de usuario

peerless-AV

peerless-AV LG-WMF86BH Manual de usuario

peerless-AV

peerless-AV YBP100 Manual de usuario

peerless-AV

peerless-AV SmartMount ST16D Guía

peerless-AV

peerless-AV ACCXT302 Guía

peerless-AV

peerless-AV SS560F Manual de usuario

peerless-AV

peerless-AV MOD-CPI Manual de usuario

peerless-AV

peerless-AV MOD-FCS2KIT300 Manual de usuario

peerless-AV

peerless-AV MOD-FPS2KIT150 Manual de usuario

peerless-AV

peerless-AV DS-MBZ647L Manual de usuario

peerless-AV

peerless-AV SMARTMAUNT Series Manual de instrucciones

peerless-AV

peerless-AV SmartMount SA761PU Manual de usuario

peerless-AV

peerless-AV FPZ-670 Guía

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario

peerless-AV PA740-S Guía

Manuales populares de Rack y soporte de otras marcas