Peak Scientific Genius 105X Series Manual de usuario

Genius1050-1051-1052-1053 User Manual Rev 9 PN UM-0002 RSID 1484 15/11/21

Genius 105X Series

User Manual

Contents

Change History 3

How to use this Manual 3

Introduction 4

Warranties and Liabilities 5

Safety Notices 6

Symbols 6

Safety Notice to Users 6

EU Declaration of Conformity 7

UK Declaration of Conformity 8

WEEE Compliance Statement 9

CSA Compliance Statement 10

Technical Speciﬁcation 11

Genius 1050 11

Technical Speciﬁcation 12

Genius 1051 12

Technical Speciﬁcation 13

Genius 1052 13

Technical Speciﬁcation 14

Genius 1053 14

Unpacking 15

Fittings Kit Contents 16

Installation 17

Generator Environment 17

Generator Overview 18

Drain Connection 21

Electrical Connection 22

Start-Up Sequence 23

Connecting to the application 24

Tubing Lengths 24

Genius 1051 Gas Flow Combinations 25

Air Selector Switch 25

Normal Operation 26

On Demand Gas 26

Generator Cycling 26

Unusual Operation 26

Service Requirements 27

Service Schedule 27

Service Indication 28

Peak Protected 29

Cleaning 30

High Duty Indication 31

High Duty Indication Reset 31

Indication of Fault 31

Troubleshooting 32

Page 2

Page 3

Change History

Rev Comment Name Date

2 Service Kit Ordering Update Liam Couttie 23/03/2018

3 Declarations Update Liam Couttie 24/04/2018

4 Genius 1053 Update Liam Couttie 15/05/2018

5 Tech Spec Update Liam Couttie 21/08/2019

6 Updates to incorporate CSA feedback Liam Couttie 10/07/2020

7 Power Cord Update Liam Couttie 18/12/2020

8 Genius 1053 Purity Figure Update Liam Couttie 08/03/2021

9 Declarations Update Liam Couttie 15/11/2021

How to use this Manual

This manual is intended for end users and has been written as a reference document

where you can skip to the relevant information.

Users can refer to the contents page to ﬁnd the relevant information.

Please review each of the following sections carefully.

Thank you for selecting Peak Scientiﬁc to meet your gas generation needs, and should

you require any further assistance or support please do not hesitate to contact Peak

Scientiﬁc or the Peak Partner from which you purchased your generator.

Page 4

Introduction

The Genius 1050, 1051, 1052 & 1053 have been developed to cater for the gas

requirements of speciﬁc LCMS, and other applications, models.

Depending on model, these generators provide a source of nitrogen gas or nitrogen

and dry air with other features including:

• Small in size – ﬁts under a standard lab bench

• Anti- vibration – maximum reduction of vibration

• Service indication – allowing you to plan your maintenance and keep your

application uptime at a maximum

• Improved drainage – reduction of moisture carry over and thus increased

reliability

• Re- heat technology – improves membrane performance and reliability

• Robust control system – improves safety and reliability of units

With the generators based on proven technology, they selectively remove oxygen,

moisture and other gases to leave clean, dry, phthalate free nitrogen gas or nitrogen

and dry air (depending on model). Two internal air compressors make these units

independent from in- house air supplies and ﬁtted castors allow the user to easily

position the units in the lab.

To ensure the generator models meet our high expectations with regards to reliability

and performance, we have tested them extensively at our manufacturing plant and with

end users around the world to ensure reliability and longevity of the system.

Page 5

Warranties and Liabilities

1. The Company warrants that it has title to the Goods.

2. Subject to the provisions of this clause the Company warrants that the Goods

shall comply in all material respects with any speciﬁcation referred to in the Order

Conﬁrmation (as the same may be amended) and shall, subject thereto, be free

from defects in material and workmanship for the lesser of a period of twelve

months from the date of delivery or thirteen months from the date of dispatch

from the factory.

3. Save as provided in this clause and except where the Goods are sold to a person

dealing as a consumer (within the meaning of the Unfair Contract Terms Act

1977) all warranties, conditions or other terms implied by statute or common

law are hereby expressly excluded save to the extent they may not be lawfully

excluded. When the Goods are sold to a consumer within the meaning of the Unfair

Contract Terms Act 1977 their statutory rights are not aected by the provisions of

this clause.

4. In the event of the Customer making a claim in respect of any defect in terms of

clause 2 hereof the Customer must.

1. Reasonably satisfy the Company that the Goods have been properly installed,

commissioned, stored, serviced and used and without prejudice to the generality

of the foregoing that any defect is not the direct or indirect result of lack of repair

and/or servicing, incorrect repair and/or servicing, use of wrong materials and/or

incorrect spare parts

2. Allow the company to inspect the Goods and/or any installation and any relevant

packaging as and when reasonably required by the Company.

5. Subject to the Company being notiﬁed of any defect as is referred to in sub-

clause 2 hereof within a reasonable time of it becoming apparent and subject always

to the terms of sub-clause 4 hereof, the Company shall, in its option, replace or

repair the defective Goods or refund a proportionate part of the Price. The Company

shall have no further liability to the Customer (save as mentioned in sub-clause 6

hereof).

6. The Company shall be liable to indemnify the Customer in respect of any claim

for death or personal injury to any person in so far as such is attributable to the

negligence or breach of duty of the Company or any failure by the Company to

comply with the provisions of sub-clause 2 hereof.

7. Save as provided in sub-clause 2 hereof the Company shall not be liable in respect

of any claim by the Customer for costs, damages, loss or expenses (whether direct,

indirect, consequential or otherwise) or indemnity in any respect howsoever arising

including, but not by way of limitation, liability arising in negligence (other than

pursuant to clause 6 above) that may be suered by the Customer or any third

party.

WARNING

CAUTION

Page 6

Safety Notices

Peak Scientiﬁc Instruments cannot anticipate every possible circumstance which may

represent a potential hazard. The warnings detailed within this manual refer to the most

likely potential hazards, but by deﬁnition cannot be all inclusive. If the user employs

an operating procedure, item of equipment or a method of working which is not

speciﬁcally recommended by Peak Scientiﬁc, the user must ensure that the equipment

will not be damaged or become hazardous to persons or property.

Symbols

This manual uses the following symbols to highlight speciﬁc areas important to the safe

and proper use of the generator.

A WARNING notice denotes a hazard. It calls attention to an operating procedure,

process or similar, which if not correctly performed or adhered to, could cause

personal injury or in the worst case death. Do not proceed beyond a WARNING

notice until the indicated conditions are fully understood or met.

A CAUTION notice denotes a hazard. It calls attention to an operating procedure,

process or similar, which if not correctly performed or adhered to, could cause

damage to the generator or the application. Do not proceed beyond a CAUTION

notice until the indicated conditions are fully understood or met.

Caution, risk of electric shock. Ensure power to the generator has been removed

before proceeding.

Safety Notice to Users

These instructions must be read thoroughly and understood before

installation and operation of your Peak Generator. Use of the generator

in a manner not speciﬁed by Peak Scientiﬁc MAY impair the SAFETY

provided by the equipment.

When handling, operating or carrying out any maintenance, personnel

must employ safe engineering practices and observe all relevant local

health and safety requirements and regulations. The attention of UK

users is drawn to the Health and Safety at Work Act 1974, and the

Institute of Electrical Engineers regulations.

If the equipment is used in a manner not speciﬁed by the manufacturer,

the protection provided by the equipment maybe impaired.

Page 7

EU Declaration of Conformity

We Peak Scientiﬁc Instruments Ltd.

Of Fountain Crescent, Inchinnan, Renfrewshire, PA4 9RE

Hereby declare that, this declaration of conformity is issued under the sole

responsibility of the manufacturer.

Equipment Type: Nitrogen Gas Generator

Model Designator: Genius XE 35 & 70

To which this declaration relates, is in conformity with the following applicable EU

Directives, harmonized standards, and other normative requirements.

• Low Voltage Directive 2014/35/EU

EN 61010-1: 2010 Safety Requirements for Electrical Equipment for Measurement,

Control and Laboratory Use.

• Electromagnetic Compatibility Directive 2014/30/EU

EN 61326-1: 2013 Electrical Equipment for Measurement, Control and Laboratory Use

– EMC Requirements. (Class A)

• Restriction on the use of certain hazardous substances in electronic equipment

(RoHS) Directive 2011/65/EU as amended by EU 2015/863.

• FCC 47 CFR Part 15 class A

Unintentional radiators; Conducted and Radiated emissions limits.

Signed for and on behalf of Peak Scientiﬁc by

Signed:

Name: Fraser Dunn

Position: Design Engineering Manager

Peak Scientiﬁc Instruments ltd,

Inchinnan, Renfrew, Scotland, PA4 9RE, UK.

Date: 16th August 2021

Page 8

UK Declaration of Conformity

We Peak Scientiﬁc Instruments Ltd.

Of Fountain Crescent, Inchinnan, Renfrewshire, PA4 9RE

Hereby declare that, this declaration of conformity is issued under the sole

responsibility of the manufacturer.

Equipment Type: Nitrogen Gas Generator

Model Designator: Genius XE 35 & 70

To which this declaration relates, is in conformity with the following applicable UK

Statutory Instruments, Standards and other normative requirements.

• The Electrical Equipment (Safety) Regulations 2016 (SI 2016 / 1101) as amended.

BS61010-1:2010 Safety Requirements for Electrical Equipment for Measurement

Control and Laboratory Use.

• The Electromagnetic Compatibility Regulations 2016 (SI 2016 / 1091) as amended.

BS61326-1:2013 Electrical Equipment for Measurement , Control and Laboratory Use

– EMC Requirements.

• The Restriction of the Use of Certain Hazardous Substances in Electrical and

Electronic Equipment Regulations 2012 (SI 2012 / 3032) as amended.

Signed for and on behalf of Peak Scientiﬁc by

Signed:

Name: Fraser Dunn

Position: Design Engineering Manager

Peak Scientiﬁc Instruments ltd,

Inchinnan, Renfrew, Scotland, PA4 9RE, UK.

Date: 16th August 2021

Page 9

WEEE Compliance Statement

The Waste Electrical and Electronic Equipment (WEEE) Regulations SI 2013 No 3113

and or the Waste Electrical and Electronic Equipment (WEEE) Directive 2012/19/EU

apply to all electrical and electronic equipment placed on the market in the UK and EU

covered by the scope of regulations which can be found in the Government Guidance

Notes (PDF) produced by the Department for Business Innovation and skills for the UK

and here for Europe.

All PEAK products that are subject to the WEEE directive are compliant with the

WEEE marking requirement. Such products are marked with the “crossed-out wheelie

bin” symbol (shown below) in accordance with European standard EN50419. All

old electrical equipment can be recycled. Please do not dispose of any electrical

equipment (including those marked with this symbol) in general rubbish bins. Please

contact your dealer or distributor for clarity.

Page 10

CSA Compliance Statement

CSA Group (Canadian Standards Authority) is a Nationally Recognised Testing

Laboratory (NRTL), headquartered in Toronto Canada.

They are authorised to evaluate product to both their own and Underwriters Laboratory

(UL) standards and certify the product to be in compliance to the relevant standards.

Peak products are certiﬁed to the current in force revision of the following standards

in order to cover both Canadian and United States requirements for “Safety

Requirements for Electrical Equipment for Measurement, Control and Laboratory use,

Part 1: general Requirements”.

Canada: CAN/CSA C22.2 No 61010-1-12

United States: UL 61010-1

As a result the products covered by this statement are certiﬁed and listed by CSA

accordingly and are entitled to carry the CSA mark with both Canadian and United

States subscripts , as shown below on the product rating label.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Generador portátil de Peak Scientific

Peak Scientific

Peak Scientific Precision 500 Manual de usuario

Peak Scientific

Peak Scientific Precision Zero Air Manual

Peak Scientific

Peak Scientific SL 100 cc Manual de usuario

Peak Scientific

Peak Scientific ZA015 Manual

Peak Scientific

Peak Scientific Infinity 9000 Manual de usuario

Peak Scientific

Peak Scientific Infinity XE 50 0 Series Manual de usuario

Peak Scientific

Peak Scientific Infinity XE 60 Series Manual de usuario

Peak Scientific

Peak Scientific Corona 1010A Manual de usuario

Peak Scientific

Peak Scientific Genius 3030 Manual de usuario

Peak Scientific

Peak Scientific Genius 1022 Manual de usuario

Peak Scientific

Peak Scientific Genius N118LA Manual de usuario

Peak Scientific

Peak Scientific Precision Hydrogen SL Manual de usuario

Peak Scientific

Peak Scientific NG3000 Manual de usuario

Peak Scientific

Peak Scientific Precision Hydrogen 1200cc Manual de usuario

Peak Scientific

Peak Scientific Genius XE QSD Manual de usuario

Peak Scientific

Peak Scientific Genius 1025 Manual de usuario

Peak Scientific

Peak Scientific TOC 1500 Manual de usuario

Peak Scientific

Peak Scientific Precision Series Manual de usuario

Peak Scientific

Peak Scientific NM20ZA Manual de usuario

Peak Scientific

Peak Scientific N 10DR Series Manual de usuario

Peak Scientific

Peak Scientific Precision Zero Air Series Manual de usuario

Peak Scientific

Peak Scientific Halo Manual de usuario

Peak Scientific

Peak Scientific Genius 1024 Manual de usuario

Peak Scientific

Peak Scientific NG2000 Manual de usuario

Manuales populares de Generador portátil de otras marcas

Kohler

Kohler 20EORZ Manual de instrucciones

Powerhorse

Powerhorse 83171 Manual de usuario

HURST

HURST ML-630-SI Manual de usuario

ETQ

ETQ TG4000 Manual de usuario

Briggs & Stratton

Briggs & Stratton 40265 Guía de configuración

ConMed

ConMed 7550 Manual de usuario

Owon

Owon Waveform Generator Manual de usuario

evertz

evertz 7700 Series Manual de usuario

Power Stroke

Power Stroke PS906025 Manual de usuario

Firefly

Firefly Cygnus CYG2400/460/24 Manual de usuario

Draper

Draper PG950S Actualización de firmware

PowerBoss

PowerBoss PowerBoss Manual de usuario

SDMO

SDMO SH 4000 Manual de usuario

EINHELL

EINHELL STE 5500 Manual de usuario

Wanco

Wanco WI3000P Manual de usuario

Full Boar

Full Boar FBT-3300 Manual de usuario

Dwyer Instruments

Dwyer Instruments ASG Manual de usuario

Westinghouse

Westinghouse WH1000i Series Manual de usuario