Peak Scientific Precision Zero Air Series Manual de usuario
Precision Zero Air Series (All Models)
Installation Guide
Copyright © Peak Scientific Instruments Ltd 2018 — Precision Zero Air Installation Guide Rev 3 RSID 310 PN IG-PREC-ZA EN —28/02/2018
Page 2
Change History
Rev Comment Name Date
3 Cleaning Information Update LC 28/02/2018
How to use this Manual
This installation guide is intended to be used as a step by step, quick start guide, to
facilitate installation and configuration.
Please visit www.peakscientific.com/downloads to
download the full User Manual for your gas generator.
Thank you for selecting Peak Scientific to meet your Gas Generation needs, and should
you require any further assistance or support please do not hesitate to contact Peak
Scientific or Peak Partner from which you purchased your Generator.
Page 3
Safety Notices
Peak Scientific Instruments cannot anticipate every possible circumstance which may
represent a potential hazard. The warnings detailed within this document detail the
most known potential hazards, but by definition cannot be all inclusive. If the user
employs an operating procedure, item of equipment or a method of working which
is not specifically recommended by Peak Scientific, the user must ensure that the
equipment will not be damaged or become hazardous to persons or property.
Symbols
This document uses the following symbols to highlight specific areas important to the
safe and proper use of the Generator
A WARNING notice denotes a hazard. It calls attention to an operating procedure,
process or similar, which if not correctly performed or adhered to, could cause
personal injury or in the worst case death. Do not proceed beyond a WARNING
notice until the indicated conditions are fully understood or met.
A CAUTION notice denotes a hazard. It calls attention to an operating procedure,
process or similar, which if not correctly performed or adhered to, could cause
damage to the Generator or the Application. Do not proceed beyond a CAUTION
notice until the indicated conditions are fully understood or met.
Caution, risk of electric shock. Ensure power to the Generator has been removed
before proceeding.
Safety Notice to Users
These instructions must be read thoroughly and understood before
installation and operation of your Peak Precision Zero Air Series
Generator. Use of the Generator in a manner not specified by Peak
Scientific MAY impair the SAFETY provided by the equipment.
When handling, operating or carrying out any maintenance, personnel
must employ safe engineering practices and observe all relevant local
health and safety requirements and regulations. The attention of UK
users is drawn to the Health and Safety at Work Act 1974, and the
Institute of Electrical Engineers regulations.
If the equipment is used in a manner not specified by the manufacturer,
the protection provided by the equipment may be impaired.
WARNING
WARNING
WARNING
WARNING
CAUTION
Page 3
Page 4
x1
1/4” x 1/4” Compression Fitting 02-4421
x1
1/4” x 1/8” Compression Fitting 02-1000
x3m
1/4” Teflon Tubing 00-1266
x1
UK Mains Cable C13 04-1028
x1
US Mains Cable C13 6-15 04-1029
x1
EU Mains Cable C13 04-1038
x1
US Mains Cable C13 5-15 04-1039
Fittings Kit
Page 5
Unpack the generator from the shipping crate and position on a flat surface, in
desired area.
WARNING the weight of the unit constitutes a two man lift. Safe lifting practices are
advised.
1.
2.
Select the ¼” x ¼” and ¼” x ⅛” Compression Fittings and attach to the AIR IN and
ZERO AIR ports respectively.
02-4421
02-1000
WARNING
Page 6
3.
Connect the supplied ¼” Teflon Tubing to the AIR IN port. Connect appropriate ⅛”
tubing, greater than 1m in length, to the generators ZERO AIR port. Please note: Only
Copper or Stainless Steel tubing should be connected to the ZERO AIR port.
Copper /
Stainless Steel
tubing only
4.
Select the appropriate mains cable from the fittings kit and plug the IEC 60320/C13
cable into the mains input at the rear of the generator.
Please note both 110V and 230V US cables have been supplied, ensure correct
mains cable is used to match the rating on the generators serial plate.
00-1266
CAUTION
04-1028/04-1029/04-1038/04-1039
Page 7
6.
5.
110VAC 50/60Hz OR 230VAC 50/60Hz
Plug the mains cable into the corresponding 110VAC 50/60Hz OR 230VAC 50/60Hz
single phase power supply.
CAUTION ensure the correct cable has been selected for your electrical supply
Press the POWER switch located at the rear of the generator.
CAUTION
UK EU
US
110V
US
230V
Page 8
8.
7.
The LEDs on the front of the generator should now illuminate YELLOW as the unit
starts up.
After approximately 60 minutes the LEDs will illuminate GREEN or BLUE (70-****
Part Numbers Only) to indicate that the generator is now ready to use.
YELLOW for 60 Minutes
GREEN / BLUE
Page 9
9.
CONGRATULATIONS
Your Peak Scientific gas generator is now fully installed. operational and ready to
supply gas on demand to your instrument.
/
Page 10
* Electrical requirements are 110 or 230VAC nominal +/- 10% depending on chosen
model. However, running continuoulsy at voltages outwith this is not recommended.
Extended periods at extremes can have a detrimental effect on the operation and life
of the Generator.
Chlorine-based bleaches/cleaning solutions should not be used on the generator, nor
should they be contained within the vicinity of the generator or compressed air supply
as these can facilitate internal and external corrosion of the generator.
Please familiarise yourself with the full User Manual available at www.peakscientific.
com/downloads This includes all other technical specifications, operating
instructions, service requirements, contact details and trouble shooting.
If you are using the Precision Air Compressor as your air supply, please refer to the
Precision Air Compressor Installation Guide, available at www.peakscientific.com/
downloads
General Notes
Otros manuales para Precision Zero Air Series
1
Tabla de contenidos
Otros manuales de Generador portátil de Peak Scientific
Peak Scientific
Peak Scientific ZA015 Manual
Peak Scientific
Peak Scientific Precision Zero Air Manual
Peak Scientific
Peak Scientific Precision 500 Manual de usuario
Peak Scientific
Peak Scientific Infinity XE 60 Series Manual de usuario
Peak Scientific
Peak Scientific NG3000 Manual de usuario
Peak Scientific
Peak Scientific Genius N118LA Manual de usuario
Peak Scientific
Peak Scientific Infinity 1032 Manual de usuario
Peak Scientific
Peak Scientific NG2000 Manual de usuario
Peak Scientific
Peak Scientific Halo Manual de usuario
Peak Scientific
Peak Scientific Genius 105X Series Manual de usuario
Peak Scientific
Peak Scientific AMD 200 Manual de usuario
Peak Scientific
Peak Scientific Genius 1024 Manual de usuario
Peak Scientific
Peak Scientific Corona 1010A Manual de usuario
Peak Scientific
Peak Scientific N 10DR Series Manual de usuario
Peak Scientific
Peak Scientific Infinity XE 60 Series Manual de usuario
Peak Scientific
Peak Scientific Genius 3030 Manual de usuario
Peak Scientific
Peak Scientific Genius NM-3G Manual de usuario
Peak Scientific
Peak Scientific Corona 1010 Manual de usuario
Peak Scientific
Peak Scientific MS Bench SCI 1 Manual de usuario
Peak Scientific
Peak Scientific Infinity 1045 Manual de usuario
