PCE Instruments PCE-COG 10 Manual de usuario

PCE-COG 10 Environmental Meter

User Manual

User manuals in various languages (français,

italiano, español, português, nederlands, türk, polski,

русский, 中文) can be found by using our

product search on: www.pce-instruments.com

Last change: 13 December 2022

v1.0

English

 
 © PCE Instruments 
 
 
Contents 
1Safety notes........................................................................................... 1 
2Specifications........................................................................................2 
3Delivery scope.......................................................................................3 
4Device description ................................................................................ 3 
5Switching the meter on and off ...........................................................4 
5.1 Lowest, highest and average measured value.................................................................. 4 
5.2 Settings............................................................................................................................ 5 
5.3 View measured values..................................................................................................... 8 
6Export of the measurement data......................................................... 9 
7Contact................................................................................................... 9 
8Disposal ................................................................................................. 9 
 
 
 

1 Safety notes

Please read this manual carefully and completely before you usethe device for thefirst time. The

device may only be used by qualified personnel and repaired by PCE Instruments personnel.

Damage or injuries caused by non-observance of the manual are excluded from our liability and

not covered by our warranty.

•The device must only be used as described inthis instruction manual.If used otherwise,

this can cause dangerous situations for the user and damage to the meter.

•The instrument may only be used if the environmental conditions (temperature, relative

humidity, …) are within the ranges stated in the technical specifications. Do not expose

the device to extreme temperatures, direct sunlight, extreme humidity or moisture.

•Do not expose the device to shocks or strong vibrations.

•The case should only be opened by qualified PCE Instruments personnel.

•Never use the instrument when your hands are wet.

•You must not make any technical changes to the device.

•The appliance should only be cleaned with a damp cloth. Use only pH-neutral cleaner,

no abrasives or solvents.

•The device must only be used with accessories from PCE Instruments or equivalent.

•Before each use, inspect the case for visible damage. If any damage is visible, do not

use the device.

•Do not use the instrument in explosive atmospheres.

•The measurement range as stated in the specifications must not be exceeded under

any circumstances.

•Non-observance of the safety notes can cause damage to the device and injuries to

the user.

We do not assume liability for printing errors or any other mistakes in this manual.

We expressly point to our general guarantee terms which can be found in our general terms of

business.

2 Specifications

Carbon monoxide (CO)

Measurement range

0 ... 1000 ppm

Resolution

1 ppm

Accuracy*

±5 % of range

The CO measurement is based on an ambient condition of 0 ... 40 °C / 32 ... 104 °F, 15 ... 95

% RH, non-condensing.

Carbon dioxide (CO²)

Measurement range

0 ... 9999 ppm

Resolution

1 ppm

Accuracy*

±3 % of rdg. ±75 ppm

The CO² measurement is based on an ambient condition of 0 ... 50 °C / 32 ... 122 °F, 0 ... 85

% RH, non-condensing.

Temperature

Measurement range

0 ... 50 °C

32 ... 122 °F

Resolution

0.1 °C / °F

Accuracy*

±2 °C / ±4 °F

Humidity

Measurement range

0 ... 100 % RH

Resolution

0.1 % RH

Accuracy

±5 % at 0 ... 20 % RH

±3.5 % at 20 ... 80 % RH

±5 % at 80 ... 100 % RH

The humidity values are based on a wind speed of 1 m/s. Accuracy is maintained after 30

minutes of acclimatisation.

Further specifications

Display

2" LC display

Measurement rate

1 Hz

Memory

for 5000 measuring points

Memory rate

1 minute, 15 minutes, 1 hour

Units

temperature: °C, °F

CO / CO²: ppm

Alarm when limit value is exceeded

visual and audible

Data export

CSV

Connection

1/4 " tripod connection

Interface

micro USB for charging the battery and for

data transfer

Power supply (rechargeable battery)

3.7 V, 1500 mAh

Power supply (mains adaptor)

primary: 100 ... 240 VAC, 50 / 60 Hz, 0.25 A

secondary: 5 VDC, 1 A

Operating conditions

0 ... 45 °C / 32 …113 °F

<95 % RH, non-condensing

Storage conditions

-10 ... 55 °C / 14 …131 °F

<95 % RH, non-condensing

Dimensions

54 x 215 x 34 mm / 2.13 x 8.46 x 1.34“

Weight

154 g / 0.34 lbs

3 Delivery scope

1 x PCE-COG 10 environmental meter

1 x micro USB cable

1 x 5 VDC mains adaptor

1 x user manual

4 Device description

No.

Description

CO and CO² sensor

Temperature and humidity sensor (at the back)

Display

Left selection key (for pressing the left virtual key)

Right selection key (for pressing the right virtual key)

On and off key

Enter and REC key

Back key

Air slits

1/4 " tripod connection

Micro USB port

5 Switching the meter on and off

To switch on the meter, press and hold the on/off key for

about two seconds. After switching on, the measurement

starts immediately.

In addition to the measured values (CO, CO², temperature

and humidity), the date, time and current battery level are

displayed.

To switch off the meter, press and hold the same key again

for approx. 2 seconds.

Note: After switching on, the meter needs approx. 30

seconds to start measuring CO.

5.1 Lowest, highest and average measured value

To view the minimum, maximum and average readings of

the individual probes, press the virtual key .

To select between the individual sensors, press the virtual

key repeatedly until the desired function is

reached. To pause the current statistics for s short time,

press the virtual key . Press this key again to

resume the measurement. If another sensor is selected, the

measurement is also resumed. Press the back key to return

to normal measurement mode.

Note: This function is only available if it has been opened.

If the function is closed, all statistics are reset.

5.2 Settings

To access the settings, press the virtual key .

With the virtual keys , you can select

between the individual functions and change parameters.

Press the enter key to open the setting option and accept

the changes. Press the back key to go back one level and

the settings are not adopted.

5.2.1 Set language

To set the language, go to the "Language" menu. Here,

you can choose either English or Chinese.

5.2.2 Change temperature units

To set the temperature unit, go to the settings and select

"Unit". You can set °C or °F as the temperature unit.

5.2.3 Set data logger

To set the data logger, go to the settings and select

"Datalogger".

Note: The data logger is always active.

5.2.3.1 Setting the memory rate

To set the memory rate, select the item "Sampling rate". Here, the memory rate can be set to 1

minute, 15 minutes or 1 hour.

5.2.3.2 Setting the recording duration

To set the recording time, select "Duration" in the data

logger settings. You can select None, 1 hour, 24 hours or

7 days. If "None" is selected, recording will continue until

the meter switches off automatically or the battery is

discharged.

After the time has elapsed, the meter switches off.

Note: Make sure that the meter is connected to the mains

adaptor during recording so that it does not switch off

during the measurement.

5.2.3.3 Display sleep mode

To switch off the display automatically, select "Sleep

mode" in the data logger settings. If this function is active,

the display switches off within 2 minutes.

5.2.4 Automatic power off

To set the automatic power off function, go to "Auto-off" in

the settings. Here, you can choose between "None", 2 and

10 minutes or one hour. If "None" is selected, the automatic

power off is permanently deactivated.

5.2.5 Set alarm limits

To set the alarm limit values, go to the settings and select the

item "Alarm". Here, an alarm limit value can be set for each

measurement function. To change the parameter, use the

virtual keys. To move to the next measurement function,

press the enter key repeatedly until you reach the desired

measurement function. If an alarm limit value is exceeded,

there will be an audible and visual alarm.

5.2.6 Set brightness

To adjust the display brightness, go to "Brightness" in the

settings where you can set the brightness of your display

according to your needs.

5.2.7 Set date and time

To set the date and time, go to the "Data / Time" item in the

settings. Here, the date and time can be set with the virtual

keys. With the enter key, you can jump to the next item.

5.3 View measured values

To view the measured values, press and hold the REC key in

measuring mode. Now all saved files are displayed. The file

name is named and sorted according to the storage date.

Select the desired file with the virtual keys and open it with

the enter key.

Now select the desired measuring function from the file. The

measured values are then displayed directly.

With the virtual keys, each individual measured value can

then be selected and read. In addition, the lowest, the

highest and the average measured value are displayed.

Note: The saved measured values can only be deleted via

the PC.

Tabla de contenidos

Otros manuales de Instrumento de medición de PCE Instruments

PCE Instruments

PCE Instruments PCE-HT 110 Manual de usuario

PCE Instruments

PCE Instruments PCE-VT 3700-ICA Manual de usuario

PCE Instruments

PCE Instruments PCE-423N Manual de usuario

PCE Instruments

PCE Instruments PCE-910 Manual de usuario

PCE Instruments

PCE Instruments DFG N Series Manual de usuario

PCE Instruments

PCE Instruments PCE-TTC 30 Manual de usuario

PCE Instruments

PCE Instruments PCE-TCR 200 Manual de usuario

PCE Instruments

PCE Instruments PCE-CT 80-FN2D5 Manual de usuario

PCE Instruments

PCE Instruments 880 Manual de usuario

PCE Instruments

PCE Instruments PCE-VE 400N4 Manual de usuario

PCE Instruments

PCE Instruments ADL 11 Manual de usuario

PCE Instruments

PCE Instruments PCE-DFG N 20K Manual de usuario

PCE Instruments

PCE Instruments PCE-353 Manual de usuario

PCE Instruments

PCE Instruments PCE-S 42 Manual de usuario

PCE Instruments

PCE Instruments PCE-CSM 6 Manual de usuario

PCE Instruments

PCE Instruments PCE-CRM 40 Manual de usuario

PCE Instruments

PCE Instruments PCE-TG 75 Manual de usuario

PCE Instruments

PCE Instruments PCE-128 Series Manual de usuario

PCE Instruments

PCE Instruments PCE-228 Manual de usuario

PCE Instruments

PCE Instruments PCE-LCT 3 Manual de usuario

PCE Instruments

PCE Instruments PCE-MSR 150 Manual de usuario

PCE Instruments

PCE Instruments PCE-HT 70-ICA Manual de usuario

PCE Instruments

PCE Instruments SG-Ultra Max Manual de usuario

PCE Instruments

PCE Instruments PCE-228 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario