PCE Instruments PCE-172 Manual de usuario

www.pce-instruments.com

Manual

DIGITAL ILLUMINANCE

METER PCE-172

CONTENT

1. INSTRUCTION.................................................................................................................3

2. FEATURES......................................................................................................................3

3. SPECIFICATIONS ...........................................................................................................3

4. NAME OF PARTS AND POSITIONS...............................................................................4

5. OPERATING INSTRUCTIONS ........................................................................................4

6. BATTERY CHECK-UP & REPLACEMENT.....................................................................4

7. SPECTRAL SENSITIVITY CHARACTERISTIC...............................................................5

8. MAINTENANCE...............................................................................................................5

9. RECOMMENDED ILLUMINATION..................................................................................5

1. INSTRUCTION

¾The digital illuminance meter is a precision instrument used to measure illuminance (lux, footcandle) in the

field.

¾It is meet CIE photopic spectral response.

¾It is fully cosine corrected for the angular incidence of light.

¾The illuminance meter is compact, tough and easy to handle owing to its constrution.

¾The light sensitive component used in the meter is a very stable, long-life silicon photo diode and spectral

response filter.

2. FEATURES

¾Light-measuring levels ranging form 0.01lux~0.1klux/0.01fc~0.01kfc, repeatedly.

¾High accuracy and rapid response.

¾Data-hold function for holding measuring values.

¾Unit and sign display for easy reading.

¾Automatic zeroing.

¾Meter corrected for spectral relative efficiency.

¾Correction factor need not be manually calculated for non-standard light sources.

¾Short rise and fall times.

¾Peak-hold function for tracing the peak signal of light pulse with least duration 10μs and keep it.

¾Capable of selecting measuring mode in lux or fc scale alternatively.

¾Auto power off 30 minutes.

¾Maximum and minimum measurements.

¾Relative reading & Reset function.

¾Easy to read large backlit display

3. SPECIFICATIONS

¾Display :3-3/4 digit LCD with high speed 41 segment bargraph.

¾Measuring Range:40.00 lux,400.0 lux,4000 lux,40.00 Klux and 400.0 Klux /40.00 fc,400.0 fc,4000 fc,40.00

Kfc.

NOTE: 1fc=10.76lux,1Klux=1000lux,1Kfc=1000fc

¾Overrange Display: LCD will show “OL” symbol.

¾Spectral Response: CIE Photopic. (CIE human eye response curve).

¾Spectral Accuracy: CIE Vλfunction f1’≦6%

¾Cosine Response: f2’

≦2%

¾Accuracy: ±5% rdg±10d.(<10,000Lux)

±10% rdg±10d.(>10,000Lux)

¾Repeatability: ±3%

¾Sampling Rate: 1.5 times/sec of analog bar-graph indication; 1.5 times/sec of digital display.

¾Photo Detector: One silicon photo diode and spectral response filter.

¾Operating temperature & Humidity :

0ºC to 40ºC(32ºF to 104ºF) & 0% to 80% RH.

¾Storage Temperature & Humidity :

-10ºC to 50ºC(14ºF to 140ºF) & 0% to 70% RH.

¾Power Source: 1 piece 9V battery.

¾Photo detector Lead Length: 150cm (approx.);

¾Photo detector Dimensions: 115L×60W×20H(mm);

¾Meter Dimensions: 203L×75W×50H;

¾Weight: 280g.

¾Accessories: Carry case, instruction manual and battery.

4. NAME OF PARTS AND POSITIONS

REL

710

1. LCD Display: 3-3/4 digit displays with a

maximum reading of 3999, and the indicating

signs of measured values, unit function

symbols and decimal points etc are display.

2. Lux key: Pressing the lux key selects taking

measurement of illuminance in lux scale

3. Fc key: Pressing the fc key selects taking

measurement of illuminance in footcandle

scale; and, 1 footcandle= 10.76lux.

4. RANGE Selector key: It indicates 40.00 lux,

400.0 lux,4000 lux,40.00 Klux and 400.0 Klux

/40.00 fc,400.0 fc,4000 fc,40.00 Kfc total 5

ranges for lux and 4 ranges for fc.

5. REL key: Relative reading control key.

6. MAX/MIN key: Maximum and minimum reading

recorder control key.

7. PEAK Hold key: Peak Hold recorder control

key.

8. BACK-LIGHT key: Back light control key.

9. Data-HOLD key: Data Hold control key.

10. Power Control key: The power switch key turns

the illuminance meter ON or OFF.

11. Photo

detector.

5. OPERATING INSTRUCTIONS

1. Power-up: Press the power key to turn the meter ON or OFF.

2. connect the photo detector.

3. Selecting the lux or fc scale: Set the range selection switch to desired lux or fc range.

4. Remove the photo detector cap and face it light source in a horizontal position.

5. read the illuminance nominal from the LCD display.

6. Overrange: If the instrument only displays “OL”, the input signal is too strong, and a higher range should be

selected.

7. Data-Hold mode: Press the hold key to select Data-Hold mode. When HOLD mode is selected, the

illuminance meter stops all further measurements. Press the HOLD key again to exit Data-Hold mode. Then

it resumes normal operation.

8. Peak-Hold recorder mode: Press and hold down PEAK key until display shown the “CAL” letter, then press

PEAK key cycle through Pmax and Pmin recorder mode, and expose the photo detector to light pulse

measuring field. Press and hold down PEAK key 2 seconds to exit PEAK recorder mode, then the meter will

resume normal operation.

9. Maximum and Minimum recorder mode: Press MAX/MIN key to cycle through Maximum(MAX) reading,

Minimum(MIN) reading and current reading(MAX/MIN blink) recorder mode. Press MAX/MIN key two

seconds to exit this mode.

10. Relative reading mode: Press REL key to enter Relative mode. The display shown zero value and the

current reading will be stored as a zero-in value. Press again to exit this mode.

11. Back-light function: Press the Backlight key to turn on. Press again to turn off.

12. When the measurement is completed, replace the photo detector cap and turn the meter off.

6. BATTERY CHECK-UP & REPLACEMENT

1. As the battery power is not sufficient, LCD will display low battery, and replacement of one new battery is

required.

2. After turning off the meter, disconnect the battery cover with a screwier.

3. Disconnect the battery from the instrument and replace it with a standard 9V battery and go for the cover.

7. SPECTRAL SENSITIVITY CHARACTERISTIC

¾To the detector, the applied photo diode with filters makes the spectral sensitivity characteristic almost

meet C.I.E.(INTERNATIONAL COMMISSION ON ILLUMINATION) Photopic curve V (λ) as the

following chart described.

8. MAINTENANCE

1. The white plastic disc on the top of the detector should be cleaned with a damp cloth when necessary.

2. Do not store the instrument where temperature or humidity is excessively high.

3. The reference level, as marker on the face plate, is the tip of the photo detector globe.

4. The calibration interval for the photo detector will vary according to operational conditions, but generally the

sensitivity decreases in direct proportion to the product of luminous intensity by the operational time. In

order to maintain the basic accuracy of the instrument, periodic calibration is recommended.

9. RECOMMENDED ILLUMINATION

1fc=10.76Lux

LOCATIONS Lux fc

OFFICE

Conference,Reception room 200~750 18~70

Clerical work 700~1,500 65~140

Typing drafting 1,000~2,000 93~186

FACTORY

Visual work at production line 300~750 28~70

Inspection work 750~1,500 70~140

Electronic parts assembly line 1,500~3,000 140~279

Packing work, Entrance passage 150~300 14~28

HOTEL

Public room, Cloakroom 100~200 9~18

Reception 200~500 18~47

Cashier 750~1,000 70~93

STORE

Indoors Stairs Corridor 150~200 14~18

Show window, Packing table 750~1,500 70~140

Forefront of show window 1,500~3,000 140~279

HOSPITAL

Sickroom, Warehouse 100~200 9~18

Medical Examination Room 300~750 28~70

Operating room, emergency treatment 750~1,500 70~140

SCHOOL

Auditorium,Indoor Gymnasium 100~300 9~28

Class room 200~750 18~70

Laboratory, Library, Drafting, room 500~1,500 47~140

NOTE: "This instrument doesn’t have ATEX protection, so it should not be used in potentially

explosive atmospheres (powder, flammable gases)."

Tabla de contenidos

Otros manuales de Instrumento de medición de PCE Instruments

PCE Instruments

PCE Instruments PCE-TDS 200 Series Manual de usuario

PCE Instruments

PCE Instruments PCE-MFI 400 Manual de usuario

PCE Instruments

PCE Instruments PCE-IT55 Manual de usuario

PCE Instruments

PCE Instruments PCE-TDS 100 HS Manual de usuario

PCE Instruments

PCE Instruments PCE-VA 11 Manual de usuario

PCE Instruments

PCE Instruments PCE-432-ICA Manual de usuario

PCE Instruments

PCE Instruments PCE - 777N Manual de usuario

PCE Instruments

PCE Instruments PCE-360 Manual de usuario

PCE Instruments

PCE Instruments PCE-428 Manual de usuario

PCE Instruments

PCE Instruments PCE-TA 30 Manual de usuario

PCE Instruments

PCE Instruments PCE-DC 50 Manual de usuario

PCE Instruments

PCE Instruments PCE-128 Series Manual de usuario

PCE Instruments

PCE Instruments PCE-353 Manual de usuario

PCE Instruments

PCE Instruments PCE-830 Manual de usuario

PCE Instruments

PCE Instruments PCE-RT 10 Manual de usuario

PCE Instruments

PCE Instruments PCE-RCM 16 Manual de usuario

PCE Instruments

PCE Instruments PCE-MAM 2 Manual de usuario

PCE Instruments

PCE Instruments PCE-FM 50N Manual de usuario

PCE Instruments

PCE Instruments Schiltknecht MiniAir 20 Manual de usuario

PCE Instruments

PCE Instruments PCE-TG 300 Manual de usuario

PCE Instruments

PCE Instruments PCE-VDL 16l Manual de usuario

PCE Instruments

PCE Instruments PCE-HWA 20BT Manual de usuario

PCE Instruments

PCE Instruments PCE-EM 29 Manual de usuario

PCE Instruments

PCE Instruments PCE-PB N Series Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario