PCchips M922ULR Manual de usuario

Preface

This publication, including all photographs, illustrations and software, is protected un-

of the material contained herein, may be reproduced without written consent of the au-

thor.

Version 3.0

Disclaimer

The information in this document is subject to change without notice. The manufac-

turer makes no representations or warranties with respect to the contents hereof and

specifically disclaims any implied warranties of merchantability or fitness for any par-

ticular purpose. The manufacturer reserves the right to revise this publication and to

make changes from time to time in the content hereof without obligation of the manu-

facturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel

Corporation.

Other product names used in this manual are the properties of their respective owners

and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digi-

tal device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not oc-

cur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

− Reorient or relocate the receiving antenna.

− Increase the separation between the equipment and the receiver.

− Connect the equipment onto an outlet on a circuit different from that to which

the receiver is connected.

− Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits governing

this device. Changes or modifications not expressly approved by the system's manu-

facturer could void the user's authority to operate the equipment.

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the follow-

ing conditions:

− This device may not cause harmful interference, and

− This device must accept any interference received, including interference

that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-

causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement

sur le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1

Introducing the Mainboard

Describes features of the mainboard,

and provides a shipping checklist.

Go to ⇒page 1

Chapter 2

Installing the Mainboard

Describes installation of mainboard

components.

Go to ⇒page 7

Chapter 3

Using BIOS

Provides information on using the BIOS

Setup Utility.

Go to ⇒page 27

Chapter 4

Using the Mainboard Software

Describes the mainboard software.

Go to ⇒page 52

Preface i

CHAPTER 1 1

Introducing the Mainboard 1

Introduction.................................................................................................1

Checklist .....................................................................................................1

Standard Items ................................................................................................. 1

Features .....................................................................................................2

Choosing a Computer Case .......................................................................4

Mainboard Components .............................................................................5

CHAPTER 2 7

Installing the Mainboard 7

Safety Precautions......................................................................................7

Quick Guide................................................................................................7

Installing the Mainboard in a Case..............................................................8

Checking Jumper Settings..........................................................................8

Setting Jumpers ............................................................................................... 8

Checking Jumper Settings ............................................................................... 9

Jumper Settings ............................................................................................... 9

Connecting Case Components.................................................................10

The Panel Connectors.....................................................................................11

Installing Hardware ...................................................................................13

Installing the Processor.................................................................................. 13

Installing Memory Modules .......................................................................... 16

Installing a Hard Disk Drive/CD-ROM......................................................... 17

Installing a Floppy Diskette Drive................................................................. 19

Installing Add-on Cards................................................................................. 19

Connecting Optional Devices........................................................................ 21

Connecting I/O Devices ............................................................................25

External Connector Color Coding ................................................................. 26

CHAPTER 3 27

Using BIOS 27

About the Setup Utility ..............................................................................27

The Standard Configuration .......................................................................... 27

Entering the Setup Utility .............................................................................. 28

Updating the BIOS ........................................................................................ 28

Using BIOS...............................................................................................29

Standard CMOS Features .............................................................................. 30

Advanced BIOS Setup Option....................................................................... 32

Advanced Chipset Features Option ............................................................... 34

iii

Integrated Peripherals Option ........................................................................ 38

Power Management Setup Option ................................................................. 42

PNP/PCI Configuration Option ..................................................................... 46

PC Health Status Option................................................................................ 48

Frequency/Voltage Control............................................................................ 49

Load Fail-Safe Defaults Option..................................................................... 50

Load Optimized Defaults Option................................................................... 50

Set Password Option...................................................................................... 50

Save & Exit Setup Option ............................................................................. 51

Exit Without Saving ...................................................................................... 51

CHAPTER 4 52

Using the Mainboard Software 52

About the Software CD-ROM ...................................................................52

Drivers and Software Installation ..............................................................52

Utility Software Reference ........................................................................53

Introducing the Mainboard

Thank you for choosing KOB P4X266a NDSUX mainboard. The KOB

P4X266a NDSUX mainboard is an ATX mainboard that uses a 4-layer printed

circuit board and measures 305 mm x 190 mm. The mainboard features a

Socket 478 that accommodates Intel Pentium 4 processors supporting system

bus (FSB) speeds of 400 MHz.

The KOB P4X266a NDSUX incorporates the VIA VT8753A Northbridge and

VT8233A (or VT8233) Southbridge chipsets which supports the AC 97 audio

codec, which combines support for DDR (Double Data Rate) SDRAM up to 3

GB.

Note: SDRAM provides 800 MBps or 1 GBps data transfer depending on whether

the bus is 100 MHz or 133 MHz. Double Data Rate SDRAM (DDR SDRAM)

doubles the rate to 1.6 GBps or 2.1 GBps by transferring data on both the ris-

ing and falling edges of the clock. DDR SDRAM uses additional power and

ground lines and requires 184-pin DIMM modules rather than the 168-pin

DIMMs used by SDRAM.

Compare the mainboard’s package contents with the following checklist:

Standard Items

• One mainboard

• One diskette drive ribbon cable

• One IDE drive ribbon cable

• One Retention Module

• Software support CD

• This user’s manual

Processor The KOB P4X266a NDSUX mainboard includes a Socket 478

that has the following features:

• Supports up to a 400/533 MHz system bus (FSB)

• Accommodates Intel Pentium 4 processors.

Chipset There are VT8753A Northbridge and VT8233A Southbridge in

this chipset in accordance with an innovative and scalable

architecture with proven reliability and performance. A few of

the chipset’s advanced features are:

• An advanced V-Link memory controller architecture that

provides the 266 MB/s bandwidth and performance nec-

essary for even the most demanding Internet and 3D

graphics

• Support for a 4xAGP interface providing vivid 3D graphics

and video performance

• An ATA 133 interface on the chipset, which helps boost

system performance by providing a high-speed connec-

tion to ATA 133 Hard Disk Drives, delivering maximum

sustained data transfer rates of 133 MB/sec

Additional key features include support for four USB ports, an

AC 97 link for audio and modem, hardware monitoring, and

ACPI/OnNow power management.

Note: This mainboard incorporates either VT8233A or

VT8233 Southbridge chipset.

Memory The mainboard supports DDR 266 SDRAM. It accommodates

three unbuffered 2.5V 184-pin slots. Each slot supports up to 1

GB with a total maximum capacity of 3 GB.

AGP The KOB P4X266a NDSUX includes a 4xAGP slot that pro-

vides eight times the bandwidth of the original AGP

specification. AGP technology provides a direct connection

between the graphics sub-system and the processor so that

the graphics do not have to compete for processor time with

other devices on the PCI bus.

AC’ 97 Audio

Codec

The AC’ 97 Audio codec is compliant with the AC 97 2.2 speci-

fication, and supports 18-bit ADC (Analog Digital Converter)

and DAC (Digital Analog Converter) resolution as well as 18-bit

stereo full-duplex codec with independent and variable sam-

pling rates. Further features include support for four analog

line-level stereo inputs.

USB USB 1.1

The VT8233A or VT8233 Southbridge chipset features the

USB 1.1 specification which can support for four USB ports.

However, if the mainboard comes with VIA VT6202, then the

mainboard supports the USB 2.0 specification.

USB 2.0 (optional)

The VIA VT6202 PCI USB 2.0 Controller is compliant with

Universal Serial Bus Specification Revision 2.0.

The USB 2.0 su

orts data transfer rates u

to 480MB/sec for

high-speed devices and specifies a microframe that will be

1/8th of a 1msec frame. This allows the USB 2.0 devices to

have small buffers even at high data rates.

The USB 1.1 connectors and other full speed cables can sup-

port the higher speed of USB 2.0 without any changes.

The chipset has the following advanced USB features:

• Compliant with Enhanced Host Controller Interface

(EHCI) Specification Revision 0.95 and Universal Host

Controller Interface (UHCI) Specification Revision 1.1

• PCI multi-function device consists of two UHCI Host Control-

lers for full/low-speed signaling and one EHCI Host

• Controller core for high-speed signaling

• Supports PCI-Bus Power Management Interface Specifi-

cation release 1.1

• Legacy support for all downstream facing ports

Expansion

Options

KOB P4X266a NDSUX has four 32-bit PCI slots, an AGP slot,

a CNR (Communications and Networking Riser) slot, and an

onboard PCI LAN interface (optional).

The KOB P4X266a NDSUX PCI slots are capable of Ultra

DMA bus mastering with transfer rates of 33/66/100/133

MB/sec.

Note: If the mainboard incorporates the VT8233A

Southbridge chipset, the Ultra DMA bus master-

ing can support up to 133 MB/sec transfer rate.

For VT8233 Southbridge chipset, the transfer rate

can support up to 100MB/sec only.

Integrated I/O The mainboard has a full set of I/O ports and connectors:

• Two PS/2 ports for mouse and keyboard

• Two serial port

• One parallel port

• One MIDI/game port

• Two USB ports

• Audio jacks for microphone, line-in and line-out

BIOS

Firmware

This mainboard uses Award BIOS that enables users to con-

figure many system features including the following:

• Power management

• Wake-up alarms

• CPU parameters

• CPU and memory timing

The firmware can also be used to set parameters for different

processor clock speeds.

There are many types of computer cases on the market. The mainboard com-

plies with the specifications for the ATX system case. Some features on the

mainboard are implemented by cabling connectors on the mainboard to indi-

cators and switches on the system case. Ensure that your case supports all

the features required. The mainboard can support one or two floppy diskette

drives and four enhanced IDE drives. Ensure that your case has sufficient

power and space for all the drives that you intend to install.

Most cases have a choice of I/O templates in the rear panel. Make sure that

the I/O template in the case matches the I/O ports installed on the rear edge

of the mainboard.

This mainboard has an ATX form factor of 305 x 190 mm. Choose a case that

accommodates this form factor.

Table of Mainboard Components

LSJ1* Single color LED header

Label Component

LUSB1* Connector for front panel USB ports

AGP1 Accelerated Graphics Port

ATX1

PANEL Front panel header

PCI1 ~ PCI4

Power connector

AUDIO

Four 32-bit add-on card slots

SIR

Mic/speaker-out header

BAT1

Serial infrared cable header

SJI

Three volt realtime clock battery

CASFAN1 Case fan connector 1

Single-color MSG (message) LED

SMART IO Connector used with media storage devices

CD1 Primary CD-in connector

USB2 Connector for front panel USB ports

CD2 Secondary CD-in connector

WOL1 Wake On LAN wakeup connector

CNR1 Communications Network Riser (CNR) slot

WOM1 Wake On Modem wakeup connector

CPU SOCKET Micro PGA 478-pin socket for Pentium 4 CPUs

* For OEM use only

Note: LED1 is usually connected to a light that indicates that the computer is

powered on. Do not install hardware or disconnect power cables while the

LED is on.

CPUFAN1 Cooling fan for CPU

This concludes Chapter 1. The next chapter explains how to install the main-

board.

DIMM1 ~ DIMM3 Three 184-pin DIMM sockets

FDD1 Floppy disk drive connector

IDE 1 Primary IDE channel

IDE 2 Secondary IDE channel

JP1 Clear CMOS jumper

JP3 BIOS protect jumper

JP5 FSB speed select jumper

LAUDIO* MIC/speaker-out header

LPANEL* Second front panel header

Tabla de contenidos

Otros manuales de Placa madre de PCchips

PCchips

PCchips M902 Series Manual de usuario

PCchips

PCchips Tidalwave W30 Manual de usuario

PCchips

PCchips M758LMR Manual de usuario

PCchips

PCchips Motherboard Manual de usuario

PCchips

PCchips M935 Series Manual de usuario

PCchips

PCchips M810 series Manual de usuario

PCchips

PCchips M925G 8.0 Manual de usuario

PCchips

PCchips M935L Manual de usuario

PCchips

PCchips M765VMRT Manual de usuario

PCchips

PCchips M770LMRT Manual de usuario

PCchips

PCchips M902LU V3.0 Manual de usuario

PCchips

PCchips M766LMRT Manual de usuario

PCchips

PCchips A41G V7.0 Manual de usuario

PCchips

PCchips M726MRT Manual de usuario

PCchips

PCchips M848LU Manual de usuario

PCchips

PCchips M765MRT Manual de usuario

PCchips

PCchips M717 Manual de usuario

PCchips

PCchips M7 Manual de usuario

PCchips

PCchips M921 Series Manual de usuario

PCchips

PCchips M925 Series Manual de usuario

PCchips

PCchips M596 Manual de usuario

PCchips

PCchips M810LMR 3.0x Manual de usuario

PCchips

PCchips M957G Manual de usuario

PCchips

PCchips A16 Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario