Pax Technology X5 Manual de usuario
X5 Wireless Data Terminal
Note: Product images shown may be different than actual product received
1.Contents Checklist
Please check the components after unpacking. If any are missing, please contact the
dealer.
Part Qty.
X5 mobile smart terminal 1
Charger 1
USB Cable 1
Wrist Strap 1
Battery 1
Product manual 1
Unscrew Piece 1
Base (optional) 1
2.Product Description
3.Installation
1. Unlock and lock the rear cover
1) To unlock the rear cover: Unscrew the four screws on the cover with screwdriver, then take
the cover off the terminal. As figure shown below.
Figure 3-1-1
2) To lock the rear cover: Put back the rear cover and make the 4 screws aligned with the 4
holes, then tighten the screws to lock the cover. As the figure shown below.
Figure 3-1-2
2. Install and remove the battery
1) To install battery: Put battery into the battery storehouse in the right direction as shown
below.
Figure 3-2-1
2) To remove battery: Place your finger in the position shown below and push forward slightly
to remove the battery.
Figure 3-2-2
3. Install SIM card/PSAM card /TF card
1) Install SIM card/PSAM card /TF card in direction shown below.
Figure 3-3-1
2) Remove SIM card/PSAM card /TF card in direction shown below.
Figure 3-3-2
4. Device Charging
The device can be charged in two ways: Using USB cable or charging base
1) By USB cable : Connect terminal to USB cable via Type-C port to charge. See port
location as figure below.
2) By charging base: Place the terminal vertically into the base, the pogo pins will be
connected themselves to charge. As figure shown below.
Figure 4-1-1
5. Wrist strap installation diagram
Figure 5-1-1
4.Instructions
1. Use of two-dimensional scanner (one-dimensional optional)
The scanner is on the top of the device. When using, enter the “Menu”， select “DEMO”>
two-dimensional (or one-dimensional) scan, align the reading window with the barcode, slightly
press the left , right scan button on the device or click "start" on the interface, the reading
window will emits the two-dimensional illumination region or one-dimensional light beam, cover
the barcode with the lighting beam emitted by the scanner, then the barcode will be read
correctly.
Note that the barcode cannot be read if it is scanned with tilted angles or without being covered
the whole area.
After reading success, the device will make a short sound, the barcode and the read times will be
rapidly displayed in the scanning area.
Figure 4-1-1
Right,Wrong,Operation demonstration for scanning bar code(2D)
Figure 4-1-2
Figure 4-1-3
2. Use of contactless card
The reading area of the contactless card is the underside of the terminal, with the reading
distance is 0-4cm. You can use it by following these steps:
1) When running the contactless card reading and writing program, the contactless card function,
which is closed by default, will be opened.
2) Enter the “Menu”>”DEMO”> select the type (ISO 14443A/B or ISO 15693) according to the
label protocol. When placing the card over the battery cover of the device, the selected
contactless card can be read correctly.
3) After reading success, the device will make a short sound and the information related to the
card will be displayed quickly in the reading window area.
3. PSAM Card
After the Mobile Smart Terminal is installed with PSAM card, you can use
the demo for the of PSAM card.
1) Enter the menu>DEMO> select "PSAM".
2) Open the PSAM application, if the status bar shows that initiation is successful, the
PSAM card is recognized correctly. Then select corresponding card slot, voltage and
baud rate and other related settings.
3) Input an APDU instruction in the input box or use the default random command, then
click "Send".
4) After sending, the message returned by the command is displayed in the result bar, and
the status bar will prompt a successful send.
5.Installation and Usage Tips
1）Do not damage the USB cable and power adapter. Otherwise, they can't be used
again.
2）Do not use battery chargers or batteries that are not special for the device to avoid damage
to the device.
3）Do not scratch the screen. Do not use pens, pencils or other sharp objects on the screen.
4）If the surface of screen is dirty, please use soft cloth to clean with diluent screen cleanser.
5）Discard the used polymer battery according to regulations. Do not throw the terminal into
the fire. Otherwise there is a risk of explosion.
6）Before connecting the power supply to the AC socket, check whether the power supply of
the socket is in accordance with the device specified operating voltage.
7）Please contact the special maintenance personnel when the device fails. The user is not
allowed to repair the device without authorization.
8）When using the device, do not irradiate human eyes to avoid injury.
6.Lithium Ion Battery Usage Tips
WARNING:
1）Don't use the battery in sunlight or smoke, dust environment.
2）Prohibited to strike, squeeze and tread on battery or throw it into the liquid and fire.
3）If battery is impressive, deformed, damaged or exothermic seriously, please stop using
immediately and replace it!
4）If the continuous working time is only half of new one, the battery life may be end. Please
replace it!
5）Must use the specified battery model and charger, otherwise there will be explosion
6）Charging time can not exceed 24 hours. If the battery is out of power, please recharge in time.
Avoid damaging the battery in over-charge and over-discharge.
7）If be non-use for long time, please recharge the battery per 6 months to avoid shortening its
life.
8）Suggest to replace it when the battery have been used for 2 years.
9）Be sure to follow the instructions to dispose the wasted batteries.
FCC Regulations:
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This device has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiated radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the party responsible for
compliance could void the user‘s authority to operate the equipment.
FCC RF Exposure Information (SAR)
This device is designed and manufactured not to exceed the emission limits for exposure
to radio frequency (RF) energy set by the Federal Communications Commission of the
United States.
The exposure standard for wireless employs a unit of measurement known as the Specific
Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg.
The FCC has granted an Equipment Authorization for this model device with all reported
SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR
information on this model device is on file with the FCC and can be found under the
Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID:V5PX5.
While there may be differences between the SAR levels of various devices and at various
positions, they all meet the government requirement.
SAR compliance for body operation is based on a separation distance of 10 mm between
the unit and the human body. Carry this device, at least 10 mm away from your body to
ensure RF exposure level compliant or lower to the reported level. To support body
operation, choose the belt clips or holsters, which do not contain metallic components, to
maintain a separation of 10 mm between this and your body.
IC Notice
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitationestautorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le
brouillageest susceptible d'en
This Class B digital apparatus complies with Canadian ICES-003.
Cetappareilnumérique de la classe B estconforme à la norme NMB-003 du Canada.
IC:11689A-X5
IC Radiation Exposure Statement
This EUT is compliance with SAR for general population/uncontrolled exposure
limits in IC RSS-102 and had been tested in accordance with the measurement
methods and procedures specified in IEEE 1528 and IEC 62209. This equipment
should be installed and operated with minimum distance 10 mm between the
radiator and your body. This device and its antenna(s) must not be co-located or
operating in conjunction with any other antenna or transmitter.
Cetappareilestconforme aux limitesd'exposition DAS incontrôlée pour la population
générale de la norme CNR-102 d'Industrie Canada et a ététestéenconformité avec
lesméthodes de mesure et procéduresspécifiéesdans IEEE 1528 et IEC 62209.
Cetappareildoitêtreinstallé et utilisé avec une distance minimale de10 mm entre
l’émetteur et votre corps. Cetappareil et saousesantennes ne doivent pas être
co-localisésoufonctionnerenconjonction avec tout autreantenneoutransmetteur.
5G 5150-5250MHz indoor use restriction warning
RSS-247Annex 9: A 9.4
The device could automatically discontinue transmission in case of absence of information to transmit,
or operational failure. Note that this is not intended to prohibit transmission of control or signaling
information or the use of repetitive codes where required by the technology.
- the device for operation in the band 5150–5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems;
In addition, high-power radars are allocated as primary users (i.e. priority users) of the bands
5250–5350 MHz and 5650–5850 MHz and that these radars could cause interference and/or damage
to LE-LAN devices.
L'appareilpeutinterrompreautomatiquement la transmission encasd'absenced'information à
transmettreoud'échecopérationnel. Ilest à noter que cela ne vise pas à interdire la transmission
de données de contrôleou de signalisationoul'utilisation de codes répétitifslorsque la
technologiel'exige.
-le dispositif de fonctionnementdans la bande 5150 – 5250 MHz n'estutiliséqu'àl'intérieur pour
réduire les risquesd'interférencesnuisibles pour les systèmes mobiles par satellite à cocanal;
Enoutre, les radars de haute puissance sontattribuésentantqu'utilisateursprincipaux (c.-à-d.
utilisateursprioritaires) des bandes 5250 – 5350 MHz et 5650 – 5850 MHz et que ces radars
pourraient causer des interférences et/ouendommager les dispositifs LAN-le.
Tabla de contenidos
Otros manuales de Terminal táctil de Pax Technology
Pax Technology
Pax Technology Aries8 Manual de usuario
Pax Technology
Pax Technology TSYS A920 Manual de usuario
Pax Technology
Pax Technology D170 Manual de usuario
Pax Technology
Pax Technology IM20 Manual de usuario
Pax Technology
Pax Technology PRIORITY A920 Manual de usuario
Pax Technology
Pax Technology D200 Manual de usuario
Pax Technology
Pax Technology A80 Manual de usuario
Pax Technology
Pax Technology SK800 Manual de usuario
Pax Technology
Pax Technology D220 Manual de usuario
Pax Technology
Pax Technology D180RF Manual de usuario
Pax Technology
Pax Technology PX7A Manual de usuario
Pax Technology
Pax Technology A35 Manual de usuario
Pax Technology
Pax Technology E600 Manual de usuario
Pax Technology
Pax Technology Smart Kiosk SK300 Manual de usuario
Pax Technology
Pax Technology SP20 Manual de usuario
Pax Technology
Pax Technology D180 Manual de usuario
Pax Technology
Pax Technology PAXPOS S80 Manual de usuario
Pax Technology
Pax Technology TSYS A920 Manual de usuario
