Pax Technology IM20 Manual de usuario

Installation Manual

PAX TECHNOLOGY LIMITED

Please make sure the following items are included. If any

items are missing, contact your dealer.

Name

Qty.

IM20 POS Terminal

USB Cable

Product Manual

PAX TECHNOLOGY LIMITED

Figure 1: Front view

1. LCD & Touch Screen

2. IC Card & Magnetic Stripe Card Reader Slot

3. Status Indicator Light

4. Camera

5. Camera working Status Light

Figure 2: Back view

6. USB 2.0 Type-B

7. RS232

8. MDB Port

PAX TECHNOLOGY LIMITED

Figure 3: View from all angles

1) SAM Cards

Figure 4: SAM card mounts

SAM3

SAM2

SAM1

Remove SAM card cover. Open the mount and insert the card

into the slot with the contacts facing downwards and the

clipped corner of the card to the upper right, then lock the

mount with the card inside and replace the cover.

2) IM20 Clearance Holes and Dimensions

3) Recommended Device Mounting

Figure 5: Installation steps

PAX TECHNOLOGY LIMITED

1) IM20 Power ON/OFF

Power on: Through the USB cable or MDB interface to the

IM20 power supply, then PAX LOGO will display

on LCD.

Power off: Disconnect the IM20 power supply, then shut

down.

2) IC Card

Put IC card chip side upward, push-in IC card slot and to

bottom.

3) Magnetic Stripe Card

Put Magnetic Stripe card stripe side downward, push-in IC card

slot and to bottom, then pull out quickly to complete the card

reading operation.

4) Contactless Card

The card read area is above the LCD, Put the card above the

LCD.

1) Do not damage any of the cables; if a cable becomes damaged,

immediately discontinue its use and seek a replacement.

2) Make sure the terminals the power or MDB cables connect to

provide the appropriate voltages at the proper pins.

3) Do not insert unknown materials into any port on the IM20,

this may cause serious damage to the device.

4) If the IM20 becomes defective, please contact a professional

technician for repairs instead of attempting them on your own.

5) The IM20 contains hardware tamper-proofing measures;

disassembly of the device will trigger the tamper circuits, at

which point it will have to be rearmed by qualified personnel

before the device is ready to resume operation.

6) The IM20 is designed for outdoor use; however, during normal

use its surface should still be keep clear of dirt and possible

liquid contaminants.

7) While the IM20 is designed to resist ingress of dust and liquids

from the front face, it is not designed to resist pressurized

liquids such as water hoses. Keep the back of the device away

from dust and liquids as much as possible.

FCC Regulations:

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference

by one of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different

from that

PAX TECHNOLOGY LIMITED

to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for

help.

FCC Caution:

Any changes or modifications not expressly approved by the

party responsible for compliance could void the user's

authority to operate this equipment.

This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set

forth for an uncontrolled environment. This equipment should be

installed and operated with minimum distance 20cm between the

radiator & your body.

Industry Canada statement

This device complies with Industry Canada license-exempt RSS

standard(s). Operation is subject to the following two

conditions:

1) this device may not cause interference, and

2) this device must accept any interference, including

interference that may cause undesired operation of the

device.

Le présent appareil est conforme aux CNR d'Industrie Canada

applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes:

1) l'appareil ne doit pas produire de brouillage, et

2) l'utilisateur de l'appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est susceptible

d'en compromettre le fonctionnement.

This device and its antenna(s) must not be co-located or

operating in conjunction with any other antenna or

transmitter, except tested built-in radios.

Cet appareil et son antenne ne doivent pas être situés ou

fonctionner en conjonction avec une autre antenne ou un

autre émetteur, exception faites des radios intégrées qui ont

été testées.

The County Code Selection feature is disabled for products

marketed in the US/ Canada.

La fonction de sélection de l'indicatif du pays est désactivée

pour les produits commercialisés aux États-Unis et au Canada.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set

forth for an uncontrolled environment. This equipment should be

installed and operated with minimum distance 20cm between the

radiator & your body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux

rayonnements IC établies pour un environnement non contrôlé.

Cet équipement doit être installé et utilisé avec un minimum de

20 cm de distance entre la source de rayonnement et votre corps.

Tabla de contenidos

Otros manuales de Terminal táctil de Pax Technology

Pax Technology

Pax Technology E600 Manual de usuario

Pax Technology

Pax Technology SK800 Manual de usuario

Pax Technology

Pax Technology Smart Kiosk SK300 Manual de usuario

Pax Technology

Pax Technology PRIORITY A920 Manual de usuario

Pax Technology

Pax Technology X5 Manual de usuario

Pax Technology

Pax Technology D180RF Manual de usuario

Pax Technology

Pax Technology SP20 Manual de usuario

Pax Technology

Pax Technology D170 Manual de usuario

Pax Technology

Pax Technology TSYS A920 Manual de usuario

Pax Technology

Pax Technology PAXPOS S80 Manual de usuario

Pax Technology

Pax Technology D200 Manual de usuario

Pax Technology

Pax Technology D180 Manual de usuario

Pax Technology

Pax Technology Aries8 Manual de usuario

Pax Technology

Pax Technology A35 Manual de usuario

Pax Technology

Pax Technology A80 Manual de usuario

Pax Technology

Pax Technology PX7A Manual de usuario

Pax Technology

Pax Technology TSYS A920 Manual de usuario

Pax Technology

Pax Technology D220 Manual de usuario

Manuales populares de Terminal táctil de otras marcas

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manual de usuario

Ingenico

Ingenico AXIUM EX4000 Manual de usuario

Heisei Electronics

Heisei Electronics Q-POS 815 Manual de usuario

Amano

Amano MTX-15 Manual de usuario

FLOWBIRD

FLOWBIRD CWT Compact Touch Manual de usuario

Demco

Demco SP7 Manual de usuario

Lathem

Lathem PC600 Series Manual de usuario

Partner

Partner MF-2352 Manual de usuario

NCR

NCR RealPOS 7460-2 Manual

Simrad

Simrad MS50 Instrucciones de montaje

Unitech

Unitech MR350 MKII Guía de inicio rápido

Jungheinrich

Jungheinrich WMT 210 Manual de usuario

Motorola

Motorola MTP850 Manual de usuario

YASKAWA

YASKAWA 62H-MDC0 Manual de usuario

MVG industries

MVG industries NeptuLink Manual de usuario

Price Industries Limited

Price Industries Limited FDC Manual de instrucciones

Honeywell

Honeywell TemaKey Manual de usuario

EBN

EBN BPC65-B-A16G Manual de usuario