Patton CopperLINK 2113A Manual de usuario

USER

MANUAL

MODEL 2113A

CopperLINK™ E1 Extender

SALES OFFICE

(301) 975-1000

TECHNICAL SUPPORT

(301) 975-1007

Part# 07M2113A-UM

Rev. A

Revised 2/2/12

An ISO-9001Certified

Company

This is a Class A device and is not intended for

use in a residential environment.

REGULATORY MODEL NUMBER:

03340D4-001

CONTENTS

1.0 Warranty Information ................................................................. 3

1.1 Regulatory Information ................................................................. 3

EMC Directive:.............................................................................. 3

Low-Voltage Direcive (Safety):..................................................... 3

1.2 Radio and TV Interference (FCC Part 15).................................... 4

1.3 CE Declaration of Conformity....................................................... 4

1.4 Authorized European Representative........................................... 4

1.5 Service.......................................................................................... 4

1.6 Safety When Working With Electricity .......................................... 5

2.0 General Information.................................................................... 7

2.1 Features........................................................................................ 7

2.2 Description.................................................................................... 7

3.0 Installation................................................................................... 8

3.1 Connecting the Line Port.............................................................. 9

3.2 Connecting the E1 Interface ....................................................... 10

3.3 Connecting Power ...................................................................... 10

4.0 Operation................................................................................... 11

4.1 Front Panel LED Status Monitors ............................................... 11

4.2 Configuration and Dip Switches.................................................. 12

Switch S4-1: Line Build Out........................................................ 12

Specifications ........................................................................... 13

A.1 Circuit Rate ................................................................................. 13

A.2 Circuit Interface .......................................................................... 13

A.3 Circuit Defaults ........................................................................... 13

A.4 Circuit Connector ........................................................................ 13

A.5 LED Status Indicators ................................................................. 13

A.6 Transmission Line ....................................................................... 13

A.7 Line Coding ................................................................................ 13

A.8 Line Interface .............................................................................. 13

A.9 Line Physical Connection ........................................................... 13

A.10 Power Supply .............................................................................. 13

A.11 Environmental ............................................................................. 13

A.12 Dimensions ................................................................................. 13

Model 2113A Series Factory

Replacement Parts and Accessories...................................... 14

1.0 WARRANTY INFORMATION

Patton Electronics warrants all Model 2113A components to be free

from defects, and will—at our option—repair or replace the product

should it fail within one year from the first date of the shipment.

This warranty is limited to defects in workmanship or materials, and does

not cover customer damage, abuse or unauthorized modification. If this

product fails or does not performs as warranted, your sole recourse shall

be repair or replacement as described above. Under no condition shall

Patton Electronics be liable for any damages incurred by the use of this

product. These damages include, but are not limited to, the following: lost

profits, lost savings and incidental or consequential damages arising

from the use of or inability to use this product. Patton Electronics spe-

cifically disclaims all other warranties, expressed or implied, and the

installation or use of this product shall be deemed an acceptance of

these terms by the user.

Note Conformity documents of all Patton products can be viewed

online at www.patton.com under the appropriate product page.

1.1 REGULATORY INFORMATION

EMC Directive:

• FCC Part 15, Class A

• EN55022, Class A

• EN55024

Low-Voltage Direcive (Safety):

• UL 60950-1/CSA 22.22 NO. 60950-1

• IEC/EN60950-1, 2nd Edition

• AS/NZS 60950-1

1.2 RADIO AND TV INTERFERENCE (FCC PART 15)

This device generates and uses radio frequency energy, and if not

installed and used properly-that is, in strict accordance with the manufac-

turer’s instructions-may cause interference to radio and television recep-

tion. The device has been tested and found to comply with the limits for a

Class A computing device in accordance with specifications in Subpart B

of Part 15 of FCC rules, which are designed to provide reasonable pro-

tection from such interference in a commercial installation. However,

there is no guarantee that interference will not occur in a particular instal-

lation. If the device does cause interference to radio or television recep-

tion, which can be determined by disconnecting the unit, the user is

encouraged to try to correct the interference by one or more of the follow-

ing measures: moving the computing equipment away from the receiver,

re-orienting the receiving antenna and/or plugging the receiving equip-

ment into a different AC outlet (such that the computing equipment and

receiver are on different branches).

1.3 CE DECLARATION OF CONFORMITY

Patton Electronics, Inc declares that this device is in compliance with the

essential requirements and other relevant provisions of Directive

2004/108/EC relating to electromagnetic compatibility and Directive

2006/95/EC relating to electrical equipment designed for use within cer-

tain voltage limits. The Declaration of Conformity may be obtained from

Patton Electronics, Inc at www.patton.com/certifications.

The safety advice in the documentation accompanying this device shall

be obeyed. The conformity to the above directive is indicated by CE

mark on the device.

1.4 AUTHORIZED EUROPEAN REPRESENTATIVE

D R M Green, European Compliance Services Limited.

Avalon House, Marcham Road, Abingdon, Oxon OX14 1UD, UK

1.5 SERVICE

All warranty and non-warranty repairs must be returned freight prepaid

and insured to Patton Electronics. All returns must have a Return Materi-

als Authorization number on the outside of the shipping container. This

number may be obtained from Patton Electronics Technical Services at:

•Tel:+1 (301) 975-1007

•Email:support@patton.com

• URL: http://www.patton.com

1.6 SAFETY WHEN WORKING WITH ELECTRICITY

• This device contains no user serviceable parts. This

device can only be repaired by qualified service per-

sonnel.

• Do not open the device when the power cord is con-

nected. For systems without a power switch and without

an external power adapter, line voltages are present

within the device when the power cord is connected.

• For devices with an external power adapter, the power

adapter shall be a listed Limited Power Source. The

mains outlet that is utilized to power the device shall be

within 10 feet (3 meters) of the device, shall be easily

accessible, and protected by a circuit breaker in com-

pliance with local regulatory requirements.

• For AC powered devices, ensure that the power cable

used meets all applicable standards for the country in

which it is to be installed.

• For AC powered devices which have 3 conductor

power plugs (L1, L2 & GND or Hot, Neutral &

Safety/Protective Ground), the wall outlet (or socket)

must have an earth ground.

• For DC powered devices, ensure that the interconnect-

ing cables are rated for proper voltage, current, antici-

pated temperature, flammability, and mechanical

serviceability.

• WAN, LAN & PSTN ports (connections) may have haz-

ardous voltages present regardless of whether the

device is powered ON or OFF. PSTN relates to inter-

faces such as telephone lines, FXS, FXO, DSL, xDSL,

T1, E1, ISDN, Voice, etc. These are known as “hazard-

ous network voltages” and to avoid electric shock use

caution when working near these ports. When discon-

necting cables for these ports, detach the far end con-

nection first.

• Do not work on the device or connect or disconnect

cables during periods of lightning activity.

WARNING

In accordance with the requirements of council direc-

tive 2002/96/EC on Waste of Electrical and Electronic

Equipment (WEEE), ensure that at end-of-life you sepa-

rate this product from other waste and scrap and deliver

to the WEEE collection system in your country for recy-

cling.

This device contains no user serviceable parts. This

device can only be repaired by qualified service per-

sonnel.

This device is NOT intended nor approved for connec-

tion to the PSTN. It is intended only for connection to

customer premise equipment.

Electrostatic Discharge (ESD) can damage equipment

and impair electrical circuitry. It occurs when electronic

printed circuit cards are improperly handled and can

result in complete or intermittent failures. Do the fol-

lowing to prevent ESD:

• Always follow ESD prevention procedures when

removing and replacing cards.

• Wear an ESD-preventive wrist strap, ensuring that it

makes good skin contact. Connect the clip to an

unpainted surface of the chassis frame to safely chan-

nel unwanted ESD voltages to ground.

• To properly guard against ESD damage and shocks,

the wrist strap and cord must operate effectively. If no

wrist strap is available, ground yourself by touching the

metal part of the chassis.

WARNING

2.0 GENERAL INFORMATION

Thank you for your purchase of this Patton Electronics product. This

product has been thoroughly inspected and tested and is warranted for

one year for parts and labor. If any questions or problems arise during

installation or use of this product, contact Patton Electronics Technical

Support at +1 (301) 975-1007.

Note The 2113A includes software developed under third party

licenses. Contact Patton for more information.

2.1 FEATURES

• Easy-to-install E1 Extender—no configuration required

• Data rate set to 2.048 Mbps on an unframed E1

• Plug ‘n’ Play for easy installations

• LED indicators for Power, Ethernet Link, and Frame

• CE marked

2.2 DESCRIPTION

The Patton Electronics Model 2113A CopperLink provides high speed 2-

wire E1 extension connectivity to ISPs, PTTs, and enterprise environments

using binder group friendly TC-PAM modulation.

Line connection is made with an RJ-45 jack. The Model 2113A is powered

by an 100/230 VAC (Universal) supply. The E1 Extender features exter-

nally-accessible DIP switches, loopback diagnostics, and CopperLink Plug

‘n’ Play.

3.0 INSTALLATION

To install the 2113A E1 Extender, do the following:

1. Connect the line interface (refer to section 3.1, “Connecting the Line

Port” on page 9)

2. Connect the E1 interface (refer to section 3.2, “Connecting the E1

Interface” on page 10).

3. Connect the power plug (refer to section 3.3, “Connecting Power” on

page 10).

Figure 1. Model 2113A rear panel

The Interconnecting cables shall be acceptable for

external use and shall be rated for the proper applica-

tion with respect to voltage, current, anticipated tem-

perature, flammability, and mechanical serviceability.

CAUTION

Power

Line

RX (75 Ohm)

(Data from

G.703/G.704

network)

TX (75 Ohm)

(Data to

G.703/G.704

network)

E1 interface

(120 Ohm)

3.1 CONNECTING THE LINE PORT

Follow the steps below to connect the Model 2113A CopperLINK Line

port.

Note The Model 2113A units work in pairs. One of the units must be

configured as a (L) Local unit, and the other unit must be config-

ured as a (R) Remote unit.

To function properly, the two E1 Extenders must be connected together

using twisted-pair, unconditioned, dry, metal wire, between 19 (0.9mm)

and 26 AWG (0.4mm). Leased circuits that run through signal equaliza-

tion equipment are not acceptable.

Follow the steps below to connect the CopperLink line port:

1. Obtain a single-twisted pair cable with an RJ-45 plug connector at

each end.

2. Plug one end of the cable into the RJ-45 socket (labeled Line) on

the CopperLink 2113A.

3. When the remote and local extender units synchronize, the front-

panel green Line LED will turn on.

The RJ-45 connector on the Model 2113A's twisted pair interface is

polarity insensitive and is wired for a two-wire interface. The signal/pin

relationship is shown in Figure 2.

Figure 2. Model 2113A (RJ-45) twisted pair line interface.

The Interconnecting cables shall be acceptable for

external use and shall be rated for the proper applica-

tion with respect to voltage, current, anticipated tem-

perature, flammability, and mechanical serviceability.

CAUTION

1 (no connection)

2 (no connection)

3 (no connection)

4 (RING)

5 (TIP)

6 (no connection)

7 (no connection)

8 (no connection)

3.2 CONNECTING THE E1 INTERFACE

Your CopperLink comes with an RJ-48C and dual BNC for connection to

E1.To connect the twisted pair cable to the CopperLink E1 port, attach

the male connector of the twisted pair cable to the female RJ-48 connec-

tor on the CopperLink. Attach the other end of the cable to the RJ-48

connector on the local E1.

The Model 2113A is equipped with dual female BNCs (TX and RX) for

connection to a 75-ohm dual coax E1 network interface. To connect the

BNC connectors of the E1 interface on the Model 2113A, simply use a

coaxial cable with a BNC connector at each end to connect the pair of

Model 2113As.

3.3 CONNECTING POWER

The Model 2113A does not have a power switch, so it powers up as soon

as it is plugged in.

An external AC or DC power supply is available separately. This connec-

tion is made via the barrel jack on the rear panel of the Model 2113A. No

configuration is necessary for the power supply (See Appendix B for

domestic and international power supply and cord options).

DC power (supplied via the power supply jack to the 2113A) must meet

the following requirements; DC power supplied must be regulated 5VDC

±5%, 1.0A minimum. Center pin is +5V. The barrel type plug has a

2.5/5.5/10mm I.D./O.D./Shaft Length dimensions.

The Interconnecting cables shall be acceptable for

external use and shall be rated for the proper applica-

tion with respect to voltage, current, anticipated tem-

perature, flammability, and mechanical serviceability.

The Interconnecting cables shall be acceptable for

external use and shall be rated for the proper applica-

tion with respect to voltage, current, anticipated tem-

perature, flammability, and mechanical serviceability.

CAUTION

Tabla de contenidos

Otros manuales de Extensor de Patton

Patton

Patton SmartNode 2290 Series Manual de usuario

Patton

Patton 2158 Manual de usuario

Patton

Patton CopperLink E2168A Manual de usuario

Patton

Patton CopperLink 1314R Manual de usuario

Patton

Patton CopperLink 1300R Manual de usuario

Patton

Patton SmartNode 2290 Series Manual de usuario

Patton

Patton CopperLink CL2300 Manual de usuario

Patton

Patton 1052AS Manual de usuario

Patton

Patton CopperLink 1101E Manual de usuario

Patton

Patton CopperLink 1211 Manual de usuario

Patton

Patton copperlink 1101 Manual de usuario

Patton

Patton CopperLink 1314R Manual de usuario

Patton

Patton CopperLink CL1300MDE Manual de usuario

Patton

Patton 2172R Manual de usuario

Patton

Patton 2168 Manual de usuario

Patton

Patton CopperLINK 2174 Manual de usuario

Patton

Patton 3231 Manual de usuario

Patton

Patton CopperLink 1101E/IP67 Manual de usuario

Patton

Patton SmartNode 4830 Series Manual de usuario

Patton

Patton SmartNode 4830 Series Manual de usuario

Patton

Patton CopperLink 2300 Manual de usuario

Patton

Patton CopperLink 1214 Manual de usuario

Patton

Patton CopperLink 1314 Manual de usuario

Patton

Patton CopperLink 1314MDE Manual de usuario

Manuales populares de Extensor de otras marcas

SY HDBT-60T Manual de usuario

Appsys ProAudio

Appsys ProAudio ADX-16 Manual de usuario

Atlona

Atlona RS232 Manual de usuario

IDK

IDK OPF-TH1000-A Manual de usuario

Enable-IT

Enable-IT 824WP Manual de usuario

Worx

Worx Landroid RadioLink WA0864 Hoja de especificaciones

TP-Link

TP-Link TL-WA730RE Manual de usuario

Camplex

Camplex CMX-HDMI-SFPL Manual de usuario

SC&T

SC&T HE03-4K Manual de usuario

Marmitek

Marmitek MegaView70 Manual de usuario

Samsung

Samsung SCS-26UC4 Manual de usuario

Foxun

Foxun SX-GES24 Manual de usuario

MuxLab

MuxLab 500771 Manual de usuario

foxunhd

foxunhd SX-AEX01 Manual de usuario

TERK Technologies

TERK Technologies LFIRX2 Manual de usuario

Devolo

Devolo Audio Extender Manual

Edimax

Edimax EW-7438RPn V2 Manual de usuario

Shinybow USA

Shinybow USA SB-6335T5 Manual de usuario