Patton CopperLink 1314 Manual de usuario

CopperLink™ Model 1314

Long Range Ethernet Extender

Quick Start Guide

Important

—This is a Class A device and is intended for use in a light industrial environment. It is not

intended nor approved for use in an industrial or residential environment.

REGULATORY MODEL NUMBER: 03340D4-001

Part Number: 07MCL1314-QS, Rev. A

Revised: April 24, 2012

Sales Office: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: support@patton.com

WWW: www.patton.com

2CopperLink Model 1314 Quick Start Guide

• Do not open the device when the power cord is connected. For sys-

tems without a power switch and without an external power

adapter, line voltages are present within the device when the power

cord is connected.

• For devices with an external power adapter, the power adapter shall

be a listed Limited Power Source The mains outlet that is utilized to

power the device shall be within 10 feet (3 meters) of the device,

shall be easily accessible, and protected by a circuit breaker in compli-

ance with local regulatory requirements.

• For AC powered devices, ensure that the power cable used meets all

applicable standards for the country in which it is to be installed.

• For AC powered devices which have 3 conductor power plugs (L1, L2

& GND or Hot, Neutral & Safety/Protective Ground), the wall outlet

(or socket) must have an earth ground.

• For DC powered devices, ensure that the interconnecting cables are

rated for proper voltage, current, anticipated temperature, flammabil-

ity, and mechanical serviceability.

• WAN, LAN & PSTN ports (connections) may have hazardous voltages

present regardless of whether the device is powered ON or OFF.

PSTN relates to interfaces such as telephone lines, FXS, FXO, DSL,

xDSL, T1, E1, ISDN, Voice, etc. These are known as “hazardous net-

work voltages” and to avoid electric shock use caution when working

near these ports. When disconnecting cables for these ports, detach

the far end connection first.

• Do not work on the device or connect or disconnect cables during peri-

ods of lightning activity.

This device is NOT intended nor approved for connection to the PSTN. It

is intended only for connection to customer premise equipment.

In accordance with the requirements of council directive 2002/96/EC on

Waste of Electrical and Electronic Equipment (WEEE), ensure that at end-

of-life you separate this product from other waste and scrap and deliver

to the WEEE collection system in your country for recycling.

WARNING

CopperLink Model 1314 Quick Start Guide 3

1.0 Configure the DIP Switches

To use DIP-switch configuration, you must first set the DIP switches to a position other than all OFF or all ON

before powering-up the CopperLink. To configure your CL1314 using the DIP switches, refer to the section enti-

tled “Hardware (DIP-switch) configuration” in the CopperLink Model 1314 User Manual.

2.0 Power up the CL1314

The CL1314 comes with one of the following power supply options:

•

External AC adaptor with detachable power cord

•

External DC power supply with terminal block connector (Model 48V-PSM3)

2.1 Models with external AC adaptor

1. Connect female plug of the AC power cord to the AC adaptor provided.

2. Connect the barrel-type connector of the AC adaptor to the Power connector on the CopperLink.

3. Insert the male plug of the AC power cord into an AC power outlet (100–240 VAC).

2.2 Models with external DC power supply

The 36-60 VDC DC to DC adapter is supplied with the DC version of the CL1314. The black and red leads plug

into a DC source (nominal 48VDC) and the barrel power connector plugs into the barrel power supply jack on the

CL1314. (See figure 1).

Figure 1. DC Power Supply

To Power

Supply Jack To -48VDC

Source

-Vin

+Vin

SWITCHING POWER SUPPLY

MODEL : SYD1106-0505

INPUT : 36-60V 0.2A MAX

OUTPUT : +5V 1.0A

OUTPUT POWER : 5W MAX

S/N: G01234567890

MADE IN CHINA BY SUNNY

Black lead (-V)

Red lead (+V)

Barrel power connector

4CopperLink Model 1314 Quick Start Guide

Figure 2.

CL1314

front panel

2.3 Power up indication

Verify that the Power LED (see figure 2) illuminates and remains lit.

3.0 Connect the CopperLink interface

1. Obtain single-twisted-pair cable with an RJ-45 plug connector at each end.

2. Plug one end of the cable into the RJ-45 socket (labeled LINE) on the CopperLink. Verify that the other

end of the cable is connected to the LINE port on other CopperLink and that the port is correctly config-

ured.

3. When a link is established, the front-panel Link LED will turn on.

4.0 Connect the Ethernet port(s)

The RJ-45 ports labeled ETH are the Auto-MDIX 10/100Base-T interface. These ports are designed to connect

directly to a 10/100Base-T device or network. You may connect this port to a hub or PC using a straight through

or crossover cable that is up to 328 ft long.

5.0 Additional information

For detailed information about installing, configuring, and operating the CopperLink, refer to the CopperLink

Model 1314 User Manual at www.patton.com/manuals/CL1314.pdf.

Power

Line Link

Ethernet Ports

CopperLink Model 1314 Quick Start Guide 5

A.0 Compliance Information

A.1 Compliance

EMC:

•

FCC Part 15, Class A

•

EN55022, Class A

•

EN55024

Safety:

•

UL 60950-1/CSA C22.2 N0. 60950-1

•

IEC/EN60950-1

•

AS/NZS 60950-1

1.2 Radio and TV Interference (FCC Part 15)

This equipment generates and uses radio frequency energy, and if not installed and used properly—that is, in

strict accordance with the manufacturer's instructions—may cause interference to radio and television recep-

tion. This equipment has been tested and found to comply with the limits for a Class A computing device in accor-

dance with the specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable

protection from such interference in a commercial installation. However, there is no guarantee that interference

will not occur in a particular installation. If the equipment causes interference to radio or television reception,

which can be determined by disconnecting the cables, try to correct the interference by one or more of the fol-

lowing measures: moving the computing equipment away from the receiver, re-orienting the receiving antenna,

and/or plugging the receiving equipment into a different AC outlet (such that the computing equipment and

receiver are on different branches).

A.3 EC Declaration of Conformity

(See section A.4 “EG-Konformitätserklärung” for German version.)

Product Description: CopperLink Model 1314

This equipment conforms to the requirements of Council Directive 1999/5/EC on the approximation of the laws

of the member states relating to Radio and Telecommunication Terminal Equipment and the mutual recognition

of their conformity.

The signed Declaration of Conformity can be downloaded from www.patton.com/certifications/.

The safety advice in the documentation accompanying the products shall be obeyed.

The conformity to the above directive is indicated by the CE sign on the device.

6CopperLink Model 1314 Quick Start Guide

A.4 EG-Konformitätserklärung

(see section A.3 “EC Declaration of Conformity” for English version)

Produktbezeichnung: CopperLink Model 1314

Die bezeichneten Produkte stimmen in der von uns in Verkehr gebrachten Ausführung mit den Vorschriften fol-

gender Richtlinie überein:

R&TTE 1999/5/EG

Richtlinie des europäischen Parlaments und des Rates zur Angleichung der Rechtsvorschriften der

Mitgliedstaaten über Funkanlagen und Telekommunikations-Endeinrichtungen und die gegenseitige

Anerkennung ihrer Konformität.

Die unterzeichnete Konformitätserklärung kann heruntergeladen werden von: www.patton.com/

certifications/.

A.5 Authorized European Representative

D R M Green

European Compliance Services Limited.

Oakdene House, Oak Road

Watchfield, Swindon, Wilts SN6 8TD, UK

Die Sicherheitshinweise in der mitgelieferten Produktdokumentation sind zu beachten.

Die Konformität mit der oben erwähnten Richtlinie wird durch das CE-Zeichen auf dem

Gerät bestätigt.

CopperLink Model 1314 Quick Start Guide 7

The information in this document is subject to change without notice. Patton Electronics assumes no

liability for errors that may appear in this document.

Trademarks statement

The term CopperLink is a trademark of Patton Electronics Company. All other trademarks presented in this docu-

ment are the property of their respective owners.

Patton support headquarters in the USA

•

Online support: Available at www.patton.com

•

E-mail support: E-mail sent to [email protected] will be answered within 1 business day

•

Telephone support: Standard telephone support is available five days a week—from 8:00 am to

5:00 pm EST (1300 to 2200 UTC/GMT)—by calling +1 (301) 975-1007

•

Support via VoIP: Contact Patton free of charge by using a VoIP ISP phone to call sip:su[email protected]

•

Fax: +1 (253) 663-5693

Alternate Patton support for Europe, Middle East, and Africa (EMEA)

•

Telephone support: Standard telephone support is available five days a week—from 8:00 am to

5:00 pm CET (0900 to 1800 UTC/GMT)—by calling +41 (0)31 985 25 55

•

Fax: +41 (0)31 985 25 26

Note For additional service and support information, refer to the “Contacting Patton for assistance” chapter

of the CopperLink Model 1314 User Manual available online at www.patton.com/manuals/

CL1314.pdf.

Warranty, Trademark, & Compliance Information

For warranty, trademark and compliance information, refer to the CopperLink Model 1314 User Manual available

online at www.patton.com/manuals/CL1314.pdf.

8CopperLink Model 1314 Quick Start Guide

NOTES

____________________________________________________________________

Tabla de contenidos

Otros manuales de Extensor de Patton

Patton

Patton SmartNode 2290 Series Manual de usuario

Patton

Patton SmartNode 2290 Series Manual de usuario

Patton

Patton CopperLink 1214 Manual de usuario

Patton

Patton CopperLINK 2113A Manual de usuario

Patton

Patton CopperLink 1314R Manual de usuario

Patton

Patton CopperLink 1101E/IP67 Manual de usuario

Patton

Patton SmartNode 4830 Series Manual de usuario

Patton

Patton SmartNode 2290 Series Manual de usuario

Patton

Patton CopperLink CL2300 Manual de usuario

Patton

Patton CopperLink CL1300 Manual de usuario

Patton

Patton CopperLink 1314R Manual de usuario

Patton

Patton CopperLink 1214E Manual de usuario

Patton

Patton CopperLINK 2174 Manual de usuario

Patton

Patton CopperLink CL2300 Manual de usuario

Patton

Patton CopperLink CL1300MDE Manual de usuario

Patton

Patton CopperLink 1314MDE Manual de usuario

Patton

Patton CopperLink 1300R Manual de usuario

Patton

Patton CopperLink 1211 Manual de usuario

Patton

Patton CopperLink E2168A Manual de usuario

Patton

Patton CopperLink CL1211E Manual de usuario

Patton

Patton CopperLink 1314R Manual de usuario

Patton

Patton 2158 Manual de usuario

Patton

Patton copperlink 1101 Manual de usuario

Patton

Patton 2157R Manual de usuario

Manuales populares de Extensor de otras marcas

SY HDBT-60T Manual de usuario

Appsys ProAudio

Appsys ProAudio ADX-16 Manual de usuario

Atlona

Atlona RS232 Manual de usuario

IDK

IDK OPF-TH1000-A Manual de usuario

Enable-IT

Enable-IT 824WP Manual de usuario

Worx

Worx Landroid RadioLink WA0864 Hoja de especificaciones

TP-Link

TP-Link TL-WA730RE Manual de usuario

Camplex

Camplex CMX-HDMI-SFPL Manual de usuario

SC&T

SC&T HE03-4K Manual de usuario

Marmitek

Marmitek MegaView70 Manual de usuario

Samsung

Samsung SCS-26UC4 Manual de usuario

Foxun

Foxun SX-GES24 Manual de usuario

MuxLab

MuxLab 500771 Manual de usuario

foxunhd

foxunhd SX-AEX01 Manual de usuario

TERK Technologies

TERK Technologies LFIRX2 Manual de usuario

Devolo

Devolo Audio Extender Manual

Edimax

Edimax EW-7438RPn V2 Manual de usuario

Shinybow USA

Shinybow USA SB-6335T5 Manual de usuario