Patton electronics EnviroNET EHA2168 Manual de usuario

USER

MANUAL

EnviroNET™ CopperLink

Ethernet Extenders

Model EHA2168

SALES OFFICE

(301) 975-1000

TECHNICAL SUPPORT

(301) 975-1007

Part# 07MEHA-QS

Doc# 06401U7-006

Rev. A

Revised 11/27/07

An ISO-9001Certiﬁed

Company

This is a Class A device and is intended for use in a

light industrial environment. It is not intended nor

approved for use in an industrial or residential

environment.

CONTENTS

1.0 Warranty Information ................................................................. 3

1.1 Radio and TV Interference (FCC Part 15) .................................... 3

1.2 CE Declaration of Conformity ....................................................... 4

1.3 Authorized European Representative........................................... 4

1.4 Service.......................................................................................... 4

2.0 General Information.................................................................... 6

2.1 Features........................................................................................ 6

2.2 Description.................................................................................... 6

3.0 Installation................................................................................... 8

3.1 Unit installation ............................................................................. 8

3.2 Grounding the EHA2168............................................................... 9

3.3 Connecting the Twisted-Pair Line Interface.................................. 9

3.4 Connecting the 10/100Base-T Ethernet Interface ...................... 10

3.5 Connecting Power ...................................................................... 11

4.0 Configuration ............................................................................ 12

5.0 Operation................................................................................... 12

5.1 Power Up .................................................................................... 12

ASpecifications ........................................................................... 13

A.1 LAN Connection .......................................................................... 13

A.2 Transmission Line ....................................................................... 13

A.3 CopperLink Line Rate ................................................................. 13

A.4 CopperLink Distance .................................................................. 13

A.5 CopperLink Surge Suppressor ................................................... 13

A.6 Power Requirements ................................................................... 13

A.7 Temperature Range .................................................................... 13

A.8 Humidity ...................................................................................... 13

A.9 Dimensions ................................................................................. 13

A.10 Weight ......................................................................................... 13

BCopperLink Series Interface Pin Assignment........................ 14

B.1 10/100Base-T Interface .............................................................. 14

RJ-45.......................................................................................... 14

B.2 CopperLink Interface .................................................................. 14

RJ-45.......................................................................................... 14

1.0 WARRANTY INFORMATION

Patton Electronics

warrants all CopperLink Ethernet Extender compo-

nents to be free from defects, and will—at our option—repair or replace

the product should it fail within one year from the ﬁrst date of the ship-

ment.

This warranty is limited to defects in workmanship or materials, and does

not cover customer damage, abuse or unauthorized modiﬁcation. If this

product fails or does not performs as warranted, your sole recourse shall

be repair or replacement as described above. Under no condition shall

Patton Electronics

be liable for any damages incurred by the use of this

product.These damages include, but are not limited to, the following: lost

proﬁts, lost savings and incidental or consequential damages arising

from the use of or inability to use this product.

Patton Electronics

spe-

ciﬁcally disclaims all other warranties, expressed or implied, and the

installation or use of this product shall be deemed an acceptance of

these terms by the user.

Note

Conformity documents of all Patton products can be viewed

online at www.patton.com under the appropriate product page.

1.1 RADIO AND TV INTERFERENCE (FCC PART 15)

This equipment generates and uses radio frequency energy, and if not

installed and used properly—that is, in strict accordance with the manu-

facturer's instructions—may cause interference to radio and television

reception. This equipment has been tested and found to comply with the

limits for a Class A computing device in accordance with the speciﬁca-

tions in Subpart B of Part 15 of FCC rules, which are designed to provide

reasonable protection from such interference in a commercial installa-

tion. However, there is no guarantee that interference will not occur in a

particular installation. If the equipment causes interference to radio or

television reception, which can be determined by disconnecting the

cables, try to correct the interference by one or more of the following

measures: moving the computing equipment away from the receiver, re-

orienting the receiving antenna, and/or plugging the receiving equipment

into a different AC outlet (such that the computing equipment and

receiver are on different branches).

1.2 CE DECLARATION OF CONFORMITY

We certify that the apparatus identiﬁed in this document conforms to the

requirements of Council Directive 1999/5/EC on the approximation of the

laws of the member states relating to Radio and Telecommunication Ter-

minal Equipment and the mutual recognition of their conformity.

The safety advice in the documentation accompanying this product shall

be obeyed. The conformity to the above directive is indicated by the CE

sign on the device.

1.3 AUTHORIZED EUROPEAN REPRESENTATIVE

D R M Green

European Compliance Services Limited.

Oakdene House, Oak Road

Watchﬁeld,

Swindon, Wilts SN6 8TD, UK

1.4 SERVICE

All warranty and non-warranty repairs must be returned freight prepaid

and insured to Patton Electronics. All returns must have a Return Materi-

als Authorization number on the outside of the shipping container. This

number may be obtained from Patton Electronics Technical Services at:

• Tel:

(301) 975-1007

• Email:

[email protected]

• URL:

http://www.patton.com

Note

Packages received without an RMA number will not be

accepted.

WARNING

This device is NOT intended nor approved for connec-

tion to the PSTN. It is intended only for connection to

customer premise equipment.

WARNING

•

This device contains no user serviceable parts. The

equipment shall be returned to Patton Electronics for

repairs, or repaired by qualiﬁed service personnel.

•

Ensure that the power cable used meets all applica-

ble standards for the country in which it is to be

installed, and that it is connected to a wall outlet

which has earth ground. The mains outlet that is uti-

lized to power the devise shall be within 10 feet (3

meters) of the device, shall be easily accessible, and

protected by a circuit breaker.

•

Do not work on the system or connect or disconnect

cables during periods of lightning activity.

•

Hazardous network voltages are present in WAN

ports regardless of whether power to the unit is ON or

OFF. To avoid electric shock, use caution when near

WAN ports. When detaching the cables, detach the

end away from the device ﬁrst.

WARNING

The Interconnecting cables shall be acceptable for

external use and shall be rated for the proper applica-

tion with respect to voltage, current, anticipated tem-

perature, ﬂammability, and mechanical serviceability

In accordance with the requirements of council direc-

tive 2002/96/EC on Waste of Electrical and Electronic

Equipment (WEEE), ensure that at end-of-life you sepa-

rate this product from other waste and scrap and deliver

to the WEEE collection system in your country for recy-

cling.

2.0 GENERAL INFORMATION

Thank you for your purchase of this Patton Electronics product. This

product has been thoroughly inspected and tested and is warranted for

one year for parts and labor. If any questions or problems arise during

installation or use of this product, contact Patton Electronics Technical

Support at +1 (301) 975-1007.

2.1 FEATURES

• Easy to install standalone EnviroNET CopperLink Ethernet Extenders

(no conﬁguration required)

• Auto MDIX Ethernet

• Auto-sensing full or half-duplex Ethernet

• Auto-sensing 10/100Base-TX

• Extends network connections up to 4,000 ft (1.22 km) over 2-wire 24-

AWG unconditioned lines

• Line rate of 12.5 Mbps

• Transparent operation

• Surge suppression up to 20 kA (8/20

• Made in the USA

2.2 DESCRIPTION

The Patton Electronics CopperLink/L and EnviroNET CopperLink/R

Ethernet Extenders provide high-speed LAN connections between

peered Ethernet LANs, remote PCs, or any other network enabled

10/100Base-T device.

Operating in pairs, a CopperLink/L (local) located at one end of the LAN

extension and the EnviroNET CopperLink/R (remote) at the other end,

these units can automatically forward LAN broadcasts, multicasts, and

frames across a 2-wire voice-grade twisted-pair link. The data is passed

transparently (unmodiﬁed) through the CopperLink Ethernet Extenders.

The CopperLink Ethernet Extenders automatically add and delete MAC

addresses, only passing packets across the CopperLink link that are

meant for the remote peered LAN.

Figure 1.

Typical application

The CopperLink/L modem and EnviroNET CopperLink/R modem work

together to create a transparent extension between two peered Ethernet

LANs. Figure 1 shows a typical point-to-point application.

3.0 INSTALLATION

Because the EnviroNET CopperLink Ethernet Extender requires no conﬁgu-

ration, it can be installed quickly.

3.1 UNIT INSTALLATION

Do the following:

1. Make a ground connection for the unit (refer to section 3.2, “Ground-

ing the EHA2168” on page 9).

2. Connect the line interface between the units (refer to section 3.3,

“Connecting the Twisted-Pair Line Interface” on page 9)

Note

See Figure 2 for the EHA2168 unit’s bottom panel arrange-

ments.

3. Connect the Ethernet interface (refer to section 3.4, “Connecting the

10/100Base-T Ethernet Interface” on page 10).

4. Connect the power plug (refer to section 3.5, “Connecting Power” on

page 11).

Figure 2.

EHA2168 Bottom Panel

EnviroNET CopperLink

EHA2168

Ethernet

port

CopperLink twisted-pair

RJ-45 interface

EnviroNET

™

POWER DATA

LINE

Power

Grounding Stud

3.2 GROUNDING THE EHA2168

Before installing the EnviroNET CopperLink Ethernet Extender, it is

important to establish a good grounding connection ﬁrst.

1. Assemble a ground wire using #10 AWG wire with green-and-yel-

low-colored insulation and two ring terminals. Make the wire long

enough to reach one of the following

earth

ground sources:

— The building ground rod (generally located at the site’s main

service entrance)

— A sprinkler system pipe

— A cold-water pipe

— Building structural steel

2. Install the grounding wire between the grounding stud (see Figure 2

on page 8) and the grounding source.

3.3 CONNECTING THE TWISTED-PAIR LINE INTERFACE

The EnviroNET CopperLink Ethernet Extender supports communication

between two peer Ethernet LAN sites over a distance of up to 4,000 ft

(1.22 km) over 24 AWG (0.5 mm) twisted-pair wire.

Note

Actual distance and link performance may vary depending on

the environment and type/gauge of wire used.

Follow the steps below to connect the CopperLink Ethernet Extenders

interfaces.

Note

The CopperLink units work in pairs. One of the CopperLink units

must be an L (local), and the other unit must be an R (remote). It

does not matter which end is the L and which is the R.The link is

always initiated by the R. As long as the L is powered on, the R

can establish a link by being powered on or by having its power

reset.

1. To function properly, the two CopperLink Ethernet Extenders must

be connected together using twisted-pair, unconditioned, dry, metal

wire, between 19 (0.9mm) and 26 AWG (0.4mm). Leased circuits

that run through signal equalization equipment are not acceptable.

2. The EnviroNET CopperLink Ethernet Extender is equipped with an

RJ-45 interface jack that can be used on the CopperLink interface

(

Line

)

. This CopperLink interface is a two-wire interface. Observe the

signal/pin relationships on the CopperLink Ethernet Extender's Cop-

perLink interface jack.

The

RJ-45 connector

on the CopperLink Ethernet Extender's twisted

pair interface

is polarity insensitive

and is wired for a two-wire inter-

face. The signal/pin relationship is shown in Figure 3.

Figure 3.

CopperLink Ethernet Extender (RJ-45) twisted pair line interface.

3.4 CONNECTING THE 10/100BASE-T ETHERNET INTERFACE

The unshielded RJ-45 port labeled

Data

on the EHA2168 model is the

Auto-MDIX10/100Base-T interface. This port is designed to connect

directly to a 10/100Base-T network. Figure 4 shows the signal/pin rela-

tionships on this interface.You may connect this port to a hub or PC

using a straight through or crossover cable that is up to 328 ft long.

Figure 4.

CopperLink Ethernet Extender 10/100Base-T RJ-45 Connector Pinout.

1 (no connection)

2 (no connection)

3 (no connection)

4 (2-Wire RING)

5 (2-Wire TIP)

6 (no connection)

7 (no connection)

8 (no connection)

1 TX+/RX+ (data output from CopperLink modem)

2 TX-/RX- (data output from Copperlink modem)

3 RX+/TX+ (data input to CopperLink modem)

4 (no connection)

5 (no connection)

6 RX-/TX-(data input to CopperLink modem)

7 (no connection)

8 (no connection)

Tabla de contenidos

Otros manuales de Extensor de Patton electronics

Patton electronics

Patton electronics CopperLink 2160 Series Manual de usuario

Patton electronics

Patton electronics SmartNode 2290 Series Manual de usuario

Patton electronics

Patton electronics CopperLINK 2173 Manual de usuario

Patton electronics

Patton electronics CopperLink 2158 Manual de usuario

Patton electronics

Patton electronics COPPERLINK 2150 Manual de usuario

Patton electronics

Patton electronics 2156 Manual de usuario

Patton electronics

Patton electronics CopperLink 2160 Series Manual de usuario

Patton electronics

Patton electronics 2113 Manual de usuario

Patton electronics

Patton electronics CopperLink Ethernet Booster 2110 Manual de usuario

Patton electronics

Patton electronics 2156 Manual de usuario

Patton electronics

Patton electronics 2113 Manual de usuario

Patton electronics

Patton electronics CopperLINK 2158B Manual de usuario

Patton electronics

Patton electronics COPPERLINK 2151 Manual de usuario

Patton electronics

Patton electronics SmartNode 2294 Manual de usuario

Patton electronics

Patton electronics EnviroNet Ethernet Extenders Manual de usuario

Patton electronics

Patton electronics 2173R Manual de usuario

Patton electronics

Patton electronics EnviroNET EHA2172 Manual de usuario

Patton electronics

Patton electronics CopperLINK 2172A Manual de usuario

Patton electronics

Patton electronics 2100 Series Manual de usuario

Patton electronics

Patton electronics Industrial Ethernet Extender with LCD Interface... Manual de instrucciones

Patton electronics

Patton electronics CopperLink 2160 Series Manual de usuario

Patton electronics

Patton electronics CopperLink 2155 Manual de usuario

Patton electronics

Patton electronics COPPER LINK 2174 Manual de usuario

Patton electronics

Patton electronics CopperLINK 2168B Manual de usuario

Manuales populares de Extensor de otras marcas

SY HDBT-60T Manual de usuario

Appsys ProAudio

Appsys ProAudio ADX-16 Manual de usuario

Atlona

Atlona RS232 Manual de usuario

IDK

IDK OPF-TH1000-A Manual de usuario

Enable-IT

Enable-IT 824WP Manual de usuario

Worx

Worx Landroid RadioLink WA0864 Hoja de especificaciones

TP-Link

TP-Link TL-WA730RE Manual de usuario

Camplex

Camplex CMX-HDMI-SFPL Manual de usuario

SC&T

SC&T HE03-4K Manual de usuario

Marmitek

Marmitek MegaView70 Manual de usuario

Samsung

Samsung SCS-26UC4 Manual de usuario

Foxun

Foxun SX-GES24 Manual de usuario

MuxLab

MuxLab 500771 Manual de usuario

foxunhd

foxunhd SX-AEX01 Manual de usuario

TERK Technologies

TERK Technologies LFIRX2 Manual de usuario

Devolo

Devolo Audio Extender Manual

Edimax

Edimax EW-7438RPn V2 Manual de usuario

Shinybow USA

Shinybow USA SB-6335T5 Manual de usuario