Parker Serviceman Plus Manual de usuario

Parker Serviceman Plus

Portable Hand-Held Measuring Instrument

2V1.0/02/12

Vorwort

Foreword

Revisions

Version Date Change

1.0 01/2012 First edition

Contact addresses

Parker Hannin

Manufacturing Germany GmbH & Co. KG

Fluid Connectors Group Europe

Tube Fittings Division Europe

P.O. Box 12 02 06, 33652 Bielefeld, Germany

Am Metallwerk 9, 33659 Bielefeld, Germany

Tel.: +49 521/40 48-0

Fax +49 521/40 48-42 80

E-mail: Ermeto@parker.com

http://www.parker.com

3V1.0/02/12

Contents

Foreword ................................................................ 2

Revisions..........................................................................2

Contact addresses ...........................................................2

1. Safety notes / product selection ....................4

1.1 Approved and intended use..................................4

1.2 Skilled personnel ..................................................4

1.3 Accuracy of the technical documentation .............4

1.4 High-pressure applications ..................................4

1.5 Service and repair.................................................5

1.6 Notes on disposal .................................................5

2. Hardware version / scope of delivery / up-

dates..............................................................6

2.1 Updates – updating the instrument's rmware......6

3. Connecting the sensors .................................8

3.1 SCM-155-0-02 with Parker analogue inputs.........8

3.2 SCM-155-2-05 with Parker CAN sensors .............9

3.3 Using the SCMA-VADC-600 current-voltage

converter.............................................................11

3.4 Using the SCMA-FCU-600 frequency converter. 11

4. Instrument settings..................................... 11

4.1 RESET – reset the MIN and MAX values ...........11

4.2 DISP – display the current readings, MIN, MAX

values, sensor limit value or temperature. .........12

4.3 SORT – reorder the channels in the display.......12

4.4 SORT RESET – reset to the factory default

sorting .................................................................13

4.5 CALC – insert the calculating channel................13

4.6 SET – basic instrument settings .........................14

4.7 START / STOP – saving the measurements.......15

4.8 Saving measurements in internal memory .........16

4.9 Online measurements using the PC software ....16

4.10 ZERO – calibrate for offset error.........................17

5. Error messages ........................................... 19

6. Maintenance, cleaning and repair ............... 20

6.1 Notes on maintenance and calibration ...............20

6.2 Repair .................................................................20

7. Accessories ................................................. 21

7.1 Accessories and spare parts for both versions...21

7.2 Analogue sensors (with automatic sensor

detection) and connecting cable .........................21

7.3 CAN-bus sensors (with automatic sensor ID)

and connecting cable..........................................22

8. Technical data.............................................. 23

4V1.0/02/12

Safety notes / product selection

1. Safety notes / product selection

1.1 Approved and intended use

This portable hand-held measuring instrument is used for measur-

ing, monitoring and saving measured values. It is useful for servic-

ing, maintenance and machine optimization. This instrument may

only be used in conjunction with sensors and accessories from

Parker's SensoControl accessories line.

Any other use is not permitted. Such use could lead to accidents

or damage to the instrument and will result in the expiration of all

warranty and indemnity claims against the manufacturer.

WARNING

Serious malfunctions leading to personal injury or dam-

age to property can result when this product is used in

applications that do not comply with the given specica-

tions or if you disregard the operating instructions and

warnings.

This instrument must not be used in hazardous areas

where there is a risk of explosions!

1.2 Skilled personnel

These operating instructions have been written for skilled person-

nel who are familiar with the valid regulations and standards rel-

evant to the application area.

1.3 Accuracy of the technical documentation

These operating instructions were created with the utmost care and

attention. However, we offer no guarantee that the data, graphics and

drawings are correct or complete. This document is subject to altera-

tion without notice.

1.4 High-pressure applications

Selection

DANGER

When selecting sensors, ensure that their overload pres-

sure will not be exceeded. It is possible for the sensor to

be damaged when the overload pressure is exceeded

(depending on the duration, frequency and level of the

pressure spike).

The "diesel effect" caused by entrapped air can result in

pressure spikes that far exceed the maximum pressure.

The nominal pressure of the sensors should be higher

than the nominal pressure of the system to be measured.

Installation

CAUTION

Please follow the instructions and observe the correct

tightening torques for ttings and adapters.

Connector thread:

1/2" BSPP (with ED seal) = 90 Nm

1/4" BSPP (with ED seal) = 30 Nm

M10x1 (with O-ring seal) = 15 Nm

5V1.0/02/12

Safety notes / product selection

1.5 Service and repair

Please contact your sales branch for assistance with repairing or

calibrating the measuring instruments.

1.6 Notes on disposal

Recycling in compliance with WEEE

After purchasing our product, you have the opportunity to return

the instrument to the sales branch at the end of its life cycle.

The EU Directive 2002/96 EC (WEEE) regulates the return

and recycling of old electrical and electronic devices. As of

13/8/2005, manufacturers of electrical and electronics

equipment in the B-2-B (business-to-business) category

are obliged to take back and recycle electrical devices free of

charge that have been sold after this date. After that date, electri-

cal devices must not be disposed of through the "normal" waste

disposal channels. Electrical equipment must be disposed of and

recycled separately. All devices that fall under this directive must

feature this logo.

Can we be of assistance?

We offer you the option of returning your old device to us at no

extra charge. We will then professionally recycle and dispose of

your device in accordance with the applicable laws.

What do you have to do?

Once your device has reached the end of its lifespan, simply return

it by parcel service (in the box) to your sales branch. We will then

take care of the recycling and disposal. You will incur no costs or

suffer any inconvenience.

Any questions?

Please contact us if you have any additional questions.

Battery disposal

The disposal of batteries is subject to the Battery Directive 2006/66/

EC in the EU, the BattG battery law of 25.6.2009 in Germany, and

the relevant national legislation internationally.

Do not dispose of batteries in normal household rubbish.

6V1.0/02/12

Hardware version / scope of delivery / updates

2. Hardware version / scope of delivery / updates

The basic conguration of your measuring instrument includes the

following:

• "SCM-155-0-02": Connections for two Parker analogue sen-

sors

• "SCM-155-2-05": Connection for a CAN bus network for a

maximum of three Parker CAN bus sensors:

• USB power supply (5V 1A), including regional adapters

• USB cable

• USB ash drive

• SensoWin software (included in delivery)

• Printed instructions, electronic operating manual (on the en-

closed disk)

The "Accessories" Chapter includes more information about the

available accessories that are not included in delivery.

2.1 Updates–updatingtheinstrument'srmware

The user can keep the measuring instrument up to date by updat-

ing the instrument's rmware. The update process is described in

this section.

The current rmware version of the instrument is shown during

boot up.

Files with a *.FIMG extension are used for the update. These

les are copied to the measuring instrument. The USB ash drive

should be used to transfer the les.

1 Copy the le with the extension *. FIMG (without sub-folders)

directly from the PC to the USB ash drive. Then plug the ash

drive into the instrument while it is switched off.

2 Disconnect all sensors that may be connected to your measur-

ing instrument.

3 Turn the instrument on and wait until the message "NO SEN-

SOR" is displayed and the Save icon appears in the top bar.

4 Briey press the ON/OFF key.

5 Wait for the following to appear on the display: FIRMWARE

UPDATE -> OK

6 OK will initiate the update: FIRMWARE UPDATE. Press Esc to

switch off the instrument without updating.

Parker.com; you will then be automatically informed of any

future rmware updates.

7V1.0/02/12

Hardware version / scope of delivery / updates

Charging the battery

CAUTION

This instrument can be charged using the USB port on your PC. However a PC delivers less power and it will take much

longer for the battery to charge.

If sensors are connected to the instrument, the current consumption of the sensors may be greater than the charging current, in which

case the battery will continue to discharge. Thus we recommend using the power supply or car charger (available separately) for

charging quickly and when using for continual measurement processes.

Changing the battery

Contact your sales representative for more information if you need to switch batteries.

Charging time from power supply:

CAN version: about 7 hours

Analogue version: about 3.5 hours

Charging time on the PC: > 7 hours

8V1.0/02/12

Connecting the sensors

3. Connecting the sensors

3.1 SCM-155-0-02 with Parker analogue inputs

Analogue cable

SCK-102-XX-02

Analogue cable

SCK-102-XX-02

9V1.0/02/12

Connecting the sensors

3.2 SCM-155-2-05 with Parker CAN sensors

CAN cable

SCK-401-XX-4F-4M

CAN resistor

SCK-401-R

CAN Y-junction

SCK-401-0.3-Y

The SORT menu option can be used to change the order of display (see page 12).

The sorting order can be reset using the Reset SORT option (see page 13). The sensors are then sorted in the order that they are

connected.

The CAN sensors are assigned to channels

in the order that they are connected. This

sorting order is maintained even while the

instrument is turned off.

Make sure that the CAN bus is terminated on

the last sensor using a SCK-401-R terminat-

ing resistor.

10 V1.0/02/12

Connecting the sensors

3.2.1 The SpeedCon connection

CAUTION

Be sure that the plastic caps are covering any unused

ports. There is no guarantee that the instrument will

be properly protected against dust and splashed water

when the inputs or outputs are uncovered. IP54 or IP67

protection is ensured only when all plastic caps are on,

or when the CAN network is in use, or when using the

CAN network or analogue sensors.

A sensor that is connected while a measurement is being

recorded is not taken into consideration. (i.e., a new chan-

nel is not displayed and the measurements from this chan-

nel are not saved).

The measurement process is continued even if a sensor

is removed during the measuring. Data recorded until the

sensor's removed is saved.

Tabla de contenidos

Otros manuales de Instrumento de medición de Parker

Parker

Parker icountOS Manual de usuario

Parker

Parker C3000 Manual de instrucciones

Parker

Parker BD15 Series Instrucciones de instalación y mantenimiento

Parker

Parker Service Master CONNECT Manual de usuario

Parker

Parker SciPres II Instrucciones de montaje

Parker

Parker PMS Manual de usuario

Parker

Parker OSP-P Manual de usuario

Parker

Parker RK 11-1669 Manual de usuario

Parker

Parker PFM1 Series Manual de usuario

Parker

Parker Digital MXR-D 4065D Manual de usuario

Parker

Parker Porter F65 Manual de usuario

Parker

Parker DIGI+ Manual de usuario

Parker

Parker SensoControl Serviceman SCM-150-1-01 Guía de instalación

Parker

Parker icountBS Series Manual de usuario

Parker

Parker SciLog SciTemp Guía

Parker

Parker ChemTec II Instrucciones de montaje

Parker

Parker SCPSi Manual de usuario

Parker

Parker SensoControl Serviceman SCM-150 Series Manual de usuario

Parker

Parker icountACM202024 Manual de usuario

Parker

Parker ServiceJunior SCJN Series Manual de usuario

Parker

Parker SensoControl ServiceJunior Series Manual de usuario

Parker

Parker XRF Manual de usuario

Parker

Parker SensoControl Manual de usuario

Parker

Parker FTIR3 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario