Paradyne 8922 Manual de usuario

8922 POTS Card

Installation and User’s Guide

Document Number 8922-A2-GN10-10

November 2004

Contents

Software and Firmware License Agreement ................................................. 2

Product Documentation Online ..................................................................... 4

8922 POTS Card Description ....................................................................... 5

Installation Overview ..................................................................................... 6

Installing POTS Cards .................................................................................. 6

Front Panel LEDs ......................................................................................... 8

Cabling .......................................................................................................... 9

Web Interface ................................................................................................ 12

Web Interface – Configuration ...................................................................... 12

Web Interface – Status ................................................................................. 13

Web Interface – Tests ................................................................................... 14

TL1 Interface ................................................................................................. 15

Command Line Interface .............................................................................. 15

Test Access Path (TAP) Architecture ........................................................... 15

TL1 Interface and CLI Test Commands ........................................................ 18

RJ21X (CA21A) Connector Pin Assignments ............................................... 19

Technical Specifications ................................................................................ 20

Warranty, Sales, Service, and Training Information ...................................... 21

Document Feedback ..................................................................................... 21

Trademarks ................................................................................................... 21

Software and Firmware License Agreement

The terms and conditions of this License Agreement (the “Agreement”) will apply to the

software and/or firmware (individually or collectively the “Software”) incorporated into

the Paradyne product (the “Product”) purchased by you and any derivatives obtained

from the Software, including any copy of either. If you have executed a separate written

agreement covering the Software supplied to you under this purchase, such separate

written agreement shall govern.

Paradyne Corporation (“Paradyne”) grants to you, and you (“Licensee”) agree to accept

a personal, non-transferable, non-exclusive, right (without the right to sublicense) to use

the Software, solely as it is intended and solely as incorporated in the Product

purchased from Paradyne or its authorized distributor or reseller under the following

terms and conditions:

1. Ownership: The Software is the sole property of Paradyne and/or its licensors. The

Licensee acquires no title, right or interest in the Software other than the license

granted under this Agreement.

2. Licensee shall not use the Software in any country other than the country in which

the Product was rightfully purchased except upon prior written notice to Paradyne

and an agreement in writing to additional terms.

3. The Licensee shall not reverse engineer, decompile or disassemble the Software in

whole or in part.

4. The Licensee shall not copy the Software except for a single archival copy.

ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS

TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED

INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU

SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.

IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS

LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS

ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE

LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE

LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU

WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT

PURCHASED BY YOU.

5. Except for the Product warranty contained in the manual, the Software is provided

“AS IS” and in its present state and condition and Paradyne makes no other

warranty whatsoever with respect to the Product purchased by you. THIS

AGREEMENT EXPRESSLY EXCLUDES ALL OTHER WARRANTIES, WHETHER

EXPRESS OR IMPLIED, OR ORAL OR WRITTEN, INCLUDING WITHOUT

LIMITATION:

a. Any warranty that the Software is error-free, will operate uninterrupted in your

operating environment, or is compatible with any equipment or software

configurations; and

b. ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION

IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A

PARTICULAR PURPOSE AND NON-INFRINGEMENT.

Some states or other jurisdictions do not allow the exclusion of implied warranties

on limitations on how long an implied warranty lasts, so the above limitations may

not apply to you. This warranty gives you specific legal rights, and you may also

have other rights which vary from one state or jurisdiction to another.

6. IN NO EVENT WILL PARADYNE BE LIABLE TO LICENSEE FOR ANY

CONSEQUENTIAL, INCIDENTAL, PUNITIVE OR SPECIAL DAMAGES,

INCLUDING ANY LOST PROFITS OR LOST SAVINGS, LOSS OF BUSINESS

INFORMATION OR BUSINESS INTERRUPTION OR OTHER PECUNIARY LOSS

ARISING OUT OF THE USE OR INABILITY TO USE THE SOFTWARE,

WHETHER BASED ON CONTRACT, TORT, WARRANTY OR OTHER LEGAL OR

EQUITABLE GROUNDS, EVEN IF PARADYNE HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY THIRD

PARTY.

7. The rights granted under this Agreement may not be assigned, sublicensed or

otherwise transferred by the Licensee to any third party without the prior written

consent of Paradyne.

8. This Agreement and the license granted under this Agreement shall be terminated

in the event of breach by the Licensee of any provisions of this Agreement.

9. Upon such termination, the Licensee shall refrain from any further use of the

Software and destroy the original and all copies of the Software in the possession of

Licensee together with all documentation and related materials.

10. This Agreement shall be governed by the laws of the State of Florida, without

regard to its provisions concerning conflicts of laws.

Product Documentation Online

Complete documentation for this product is available at www.paradyne.com.

Select Library →Technical Manuals.

To order a paper copy of a Paradyne document, or to speak with a sales representative,

please call 1-727-530-2000.

Document Number Document Title

8400-A2-GB20 Shelf Concentration and Processing (SCP) Card User’s Guide

8400-A2-GZ40 Shelf Concentration and Processing (SCP) Card Installation

Instructions

8400-A3-GB21 8620 and 8820 Broadband Access Concentrators TL1

Reference

8400-A3-GB22 8620 and 8820 Broadband Access Concentrators Command

Line Interface (CLI) Reference

8620-A2-GN20 8620 Broadband Access Concentrator Installation Guide

8820-A2-GN20 8820 Broadband Access Concentrator Installation Guide

8922 POTS Card Description

The 8922 POTS (Plain Old Telephone Service) card can be used in any 8620 or 8820

Broadband Access Concentrator (BAC) managed by a Shelf Concentration and

Processing (SCP) card. The model 8820-A2-520 BAC is required for test access.

Physical Description

Each 8922 POTS card connects through one 50-position Telco connector (RJ21X) on

the rear of the chassis. The card supports:

24 POTS ports

Standard 2-wire single party service

Loop start

DTMF and Pulse

5 REN

G.711 PCM, G.726 ADPCM, G.729 CELP

Test access for connection to an external test head (with Test Access System

Interface Module)

Custom Local Area Signaling Services

For a complete list of supported features, see Technical Specifications on page 20.

ALARMS

MajorMinor

Fan

POWER

SERIAL

SMCM

CLOCK

ALARM

24681012141618

1357911131517

LAN/WAN SLOT

CLOCK

SERIAL

MCC

ALARM

48V RTN

48V NEG

POWER ENTRY MODLE

LEFT NIT: LINE A

RIGHT NIT: LINE B

WARNING!

POWER MUST BE DISCONNECTED AT THE SOURCE

BEFORE REMOVING OR INSTALLING THIS PWR ENTRY MODULE

48V RTN

48V NEG

POWER ENTRY MODLE

LEFT NIT: LINE A

RIGHT NIT: LINE B

WARNING!

POWER MUST BE DISCONNECTED AT THE SOURCE

BEFORE REMOVING OR INSTALLING THIS PWR ENTRY MODULE

8820 BAC

with POTS Card

DSL + POTS

CPX- 000 MG

04-17538

ATM

PSTN

POTS Phones

GR-303,

V5.x

Class 5

Switch

LES or MGCP Signaling

Installation Overview

In the course of installing the 8922 POTS card, you will:

❑Obtain the applicable cable; refer to Cabling on page 9.

❑Make sure the BAC is installed and power is supplied to the chassis.

❑Install the card in the BAC.

❑Connect to a 66 Block or other termination point.

❑Configure your POTS card and IADs using the web or TL1 interface. Refer to the

SCP card’s online Help or the 8620 and 8820 Broadband Access Concentrators

TL1 Reference for configuration information.

Be sure to register your warranty at www.paradyne.com/warranty.

Installing POTS Cards

HANDLING PRECAUTIONS FOR

STATIC-SENSITIVE DEVICES

This product is designed to protect sensitive

components from damage due to electrostatic

discharge (ESD) during normal operation. When

performing installation procedures, however, take

proper static control precautions to prevent damage.

If you are not sure of the proper static control

precautions, contact your service representative.

A POTS card can be installed in, removed from, and replaced in a BAC without

disrupting service to the other cards in the chassis.

Procedure

To install the POTS card:

1. Determine in which slot the unit will be installed. Verify that cards in adjacent slots

have been fastened.

2. Remove the filler plate from the installation slot and store for possible later use.

3. Holding the POTS card vertically with component side facing right, insert it into the

top and bottom card guides.

CAUTION:

Do not force the unit into the slot. This could damage the backplane

connectors. If the card does not seat properly, remove the card and reinstall

it. If it still does not seat properly, call your service representative.

4. Slide the unit into the slot until the power and network connectors seat firmly in the

mating connectors on the backplane.

The unit performs a power-on self-test. All of the LEDs turn ON and OFF briefly.

When the self-test is completed successfully, the SYSTEM OK LED begins to

pulse.

If the LED is not pulsing, notify your service representative. See Front Panel LEDs

on page 8.

5. Secure the unit by fastening the screws at each end of the faceplate.

00-16709

ALARMS

MajorMinor

Fan

POWER

SERIAL

SMCM

CLOCK

ALARM

246810 12 14 16 18

135

7911 13 15 17

LAN/WAN SLOT

CLOCK

SERIAL

MCC

ALARM

48V RTN

48V NEG

POWERENTRYMODULE

LEFTUNIT:LINEA

RIGHTUNIT:LINEB

WARNING!

POWER MUST BE DISCONNECTED ATTHE SOURCE

BEFORE REMOVING OR INSTALLINGTHIS PWR ENTRY MODULE

48V RTN

48V NEG

POWERENTRYMODULE

LEFTUNIT:LINEA

RIGHTUNIT:LINEB

WARNING!

POWER MUST BE DISCONNECTED ATTHE SOURCE

BEFORE REMOVING OR INSTALLINGTHIS PWR ENTRY MODULE

DSL

SYSTEM

Alm

Test

ETHERNET

Coll

DSLPORT

MCP

SYSTEM

Alm

Test

ETHERNET

Coll

Front Panel LEDs

The following table describes the meaning and states of the LEDs on the

front panel.

Type LED LED is . . . *

* Pulsing: LED turns off momentarily once per second.

Fast Blinking: LED turns off and on in equal duration 4 times per

second.

Indicating . . .

SYSTEM OK Green, On

Off

Green, Pulsing

Card failure. System processing

functions have stopped.

No power to card.

Card is functioning normally.

Alrm Amber, On

Off

Alarm is present on the card.

Normal operation, no alarms.

Te s t A m b e r, O n

Off

Test in progress.

Normal operation, no tests.

SYS BUS TX Off

Green, Fast

Blinking

Inactive.

Cells are being transmitted.

RX Off

Green, Fast

Blinking

Inactive, link down.

Cells are being received.

LOC Yellow, On

Off

Loss Of Clock. ATM bus clock

signal is not present.

Normal operation.

VOICE

PORT

VOICE

PORT

Green, On

Green, Blinking

Off

At least one port is enabled and no

ports are in the off-hook state.

At least one port is enabled and in

the off-hook state.

No ports are enabled.

04-17537

POTS

8922

SYSTEM

Alrm

Test

LOC

SYS BUS

VOICE PORT

Cabling

The POTS card normally is connected to a 66 Block using a straight-through cable with

two RJ21X plugs. The cable you need depends on the hardware configuration of the

66 Block or other connection point. See Table 3, RJ21X Connector Pinouts, on page 19.

Attach the cable to the 50-pin Telco jack on the back of the DSLAM that is associated

with the slot the POTS card resides in.

Fastening the Cable with Cable Ties

Procedure

To fasten the Telco connector to the chassis using the provided cable ties:

1. Replace the longer captive screw on the cable connector with the #4-40 Phillips

pan-head screw shipped in a plastic bag with the BAC chassis.

2. Locate the connector on the back of the chassis that corresponds with the slot

where you installed the POTS card. Connectors are labeled 1–3 on the 8620

chassis, and 1–18 on the 8820 chassis.

3. Plug the Telco 50-pin cable into the appropriate connector.

4. Thread the provided cable tie through the anchor mount on the end of the connector

where the cable will lie. Tighten the cable tie around the connector and cut off any

excess.

5. Secure the other end of the Telco 50-pin cable by tightening the captive pan-head

screw.

01-16900

Anchor

Mount

Telco 50-Pin

Connector

Cable

Tie

Replaced with

Supplied #4-40

Phillips Pan-head

Screw

Fastening a Cable with Locking Pivot Brackets

Procedure

To fasten a Telco connector to the chassis with locking pivot brackets:

1. Replace the longer captive screw on the cable connector with the #4-40 Phillips

pan-head screw shipped in a plastic bag with the BAC chassis.

2. Install the locking pivot bracket onto the cable end of the connector using the

captive screw, as illustrated below.

3. Locate the connector on the back of the chassis that corresponds with the slot

where you installed the POTS card. Connectors are labeled 1–3 on the 8620

chassis, and 1–18 on the 8820 chassis.

Locking Pivot

Bracket Captive #4-40 Phillips-Head Screw

(Part of Locking Pivot Bracket)

Customer-Supplied

Cable with Connector Replace with a shorter

Captive Screw provided

with the Pivot Bracket

99-16162a-02

Locking Pivot

Bracket

Tabla de contenidos

Otros manuales de Software de Paradyne

Paradyne

Paradyne OPENLANE Manual de usuario

Paradyne

Paradyne ACCULINK 3150 Manual de instrucciones

Paradyne

Paradyne 8995 Manual de instrucciones

Paradyne

Paradyne 8995 Manual de usuario

Paradyne

Paradyne ACCULINK 7800-D1-999 Manual de usuario

Paradyne

Paradyne Jetstream CPX-1000 Manual de usuario

Paradyne

Paradyne Jetstream CPX-1000 Manual de usuario

Paradyne

Paradyne OpenLane SLM 5.5 Manual de servicio

Paradyne

Paradyne Jetstream CPX-1000 Manual de usuario

Manuales populares de Software de otras marcas

COMPRO

COMPRO COMPROFM Manual de usuario

Muratec

Muratec OFFICEBRIDGE ONLINE Manual de usuario

Oracle

Oracle Contact Center Anywhere 8.1 Manual de usuario

Adobe

Adobe 65007312 - Photoshop Lightroom Manual

Avaya

Avaya NULL One-X for RIM Blackberry Manual de usuario

HP ProLiant BL420c Manual de usuario

PS Audio

PS Audio PowerPlay Manual del propietario

Brady

Brady LOCKOUT PRO 3.0 Manual de servicio

Avaya

Avaya Interaction Center Manual de usuario

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Manual

Novell

Novell GROUPWISE 8 - INTERNET AGENT Manual de usuario

Oracle

Oracle Application 9i Manual de usuario

Acer

Acer RDM Manual de usuario

Canon

Canon Vixia HF21 Manual de usuario

Canon

Canon ZR950 Manual de usuario

Samsung

Samsung Auto Backup Manual de usuario

Polycom

Polycom Vortex EF2201 Instrucciones de instalación y funcionamiento

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Manual de usuario