Paradyne ACCULINK 3160 Manual de usuario

ACCULINK3160

DSU/CSU

QUICK REFERENCE

Document No. 3160-A2-GL11-80

Printed in U.S.A.

Notice

This publication is protected by federal copyright law. No part of this publication may be

copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated

into any human or computer language in any form or by any means, electronic,

mechanical, magnetic, manual or otherwise, or disclosed to third parties without the

express written permission of Paradyne Corporation, 8545 126th Ave. N., Largo,

FL 33773.

Paradyne Corporation makes no representation or warranties with respect to the

contents hereof and specifically disclaims any implied warranties of merchantability or

fitness for a particular purpose. Further, Paradyne Corporation reserves the right to

revise this publication and to make changes from time to time in the contents hereof

without obligation of Paradyne Corporation to notify any person of such revision or

changes.

Changes and enhancements to the product and to the information herein will be

documented and issued as a new release to this manual.

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor directly for

any help needed. For additional information concerning warranty, sales, service, repair,

installation, documentation, training, distributor locations, or Paradyne worldwide office

locations, use one of the following methods:

HInternet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be

sure to register your warranty at www.paradyne.com/warranty.)

HTelephone: Call our automated system to receive current information by fax or to

speak with a company representative.

— Within the U.S.A., call 1-800-870-2221

— Outside the U.S.A, call 1-727-530-2340

Document Feedback

We welcome your comments and suggestions about this document. Please mail them

to Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773,

or send e-mail to [email protected]. Include the number and title of this

document in your correspondence. Please include your name and phone number if you

are willing to provide additional clarification.

Trademarks

ACCULINK is a registered trademark of Paradyne Corporation. All other products and

services mentioned are the trademarks, service marks, registered trademarks, or

registered service marks of their respective owners.

ACCULINKr3160 DSU/CSU

Quick Reference

Document Number 3160-A2-GL11-80

May 2000

Product Documentation on the World Wide Web

We provide complete product documentation online. This lets you search the

documentation for specific topics and print only what you need, reducing the waste of

surplus printing. It also helps us maintain competitive prices for our products.

Complete documentation for this product is available at www.paradyne.com.

Select

Library

→

Technical Manuals

→

T1/E1 Digital Access Devices.

Select the following document:

3160-A2-GB24

ACCULINK DSU/CSU, Models 3160-A4, 3161, 3164-A2, and 3165-A4 Operator’s

Guide

To request a paper copy of a Paradyne document:

HWithin the U.S.A., call 1-800-PARADYNE (1-800-727-2396)

HOutside the U.S.A., call 1-727-530-8623

Installation Procedure

Before installing the DSU/CSU, read the

Important Safety Instructions

beginning on

page 25.

The following procedure is for experienced DSU/CSU users who are familiar with the

3160 DSU/CSU installation process and have no special requirements for their

application. See the

ACCULINK DSU/CSU Operator’s Guide

for more information.

1. Attach the power cord to the rear of the DSU/CSU and the other end to a grounded

115 Vac power outlet.

2. Attach the DSU/CSU network connection to the T1 network using the appropriate

cable. Attach the 3160 DSU/CSU to the customer premises equipment via the DTE

(DSX-1) and/or port connectors.

3. Power on the DSU/CSU to perform the power-on self-test.

4. If you intend to use front panel emulation, connect the cable from the PC to the

COM port on the rear panel of the DSU/CSU.

5. If you intend to manage the DSU/CSU with SNMP over an Ethernet LAN, connect

the 10BaseT port to your LAN and assign an IP address to the port. See

Configuration Procedures

on page 4.

6. If you do not intend to use the DTE Drop/Insert T1 port, disable it. See

Configuration Procedures

on page 4. The default setting for this port is Enabled.

7. Customize the configuration options for your environment as required.

8. During the power-on self-test, the FAIL LED flashes, then all LEDs blink twice.

When the test is complete, verify that the DSU/CSU is functional by observing that

the OK, NETWORK SIG, and DTE SIG LEDs are lit.

PORT 2PORT 1CLOCK IN

POWER

10 BASE-T

COM DSX-1MODEM NETWORK

PORT 2PORT 1CLOCK IN

PORT 4PORT 3

AUX PORT COM PORT MODEM DTE

POWER NETWORK

CAUTION:

AUX PORT OR COM PORT MUST NOT BE CONNECTED TO PSTN OR T1 NETWORK

NEC

CLASS 2

INPUT

99-15573-01

Modem

Power

Modem

Power

Front

Panel

3164 DSU/CSU

3164

DSU/CSU

3160

DSU/CSU

Serial

Port

COM Port Network

Port

Modem

Port

COM

Port Network

Port

Modem

Port

Network

Port

Router

SNMP

Manager

SNMP

Manager

Terminal

PSTN

T1 Network

10BaseT

Port

10BaseT

SNMP Manager

Cabling Examples

Configuration Procedures

For detailed configuration procedures see Chapter 4,

Configuration

, and Appendix C,

Configuration Options

, of the

Operator’s Guide

Displaying/Editing Configuration Options

To display/edit configuration options:

1. From the top-level menu screen (which you can access by pressing the key),

select Cnfig.

2. Select the configuration option set to be copied into the Edit area by using the

appropriate Function key (F1, F2, or F3). Use the scroll keys ( and ), if

necessary.

The Factory 1 configuration for ESF framing format and B8ZS line coding format is

the default configuration and is appropriate for most networks. For D4 framing

format and AMI line coding format, use the Factory 2 configuration. See Table 3.

3. Select Edit.

4. From the Edit screen, select the functional group you want to edit by pressing the

appropriate Function key. Use the scroll keys ( and ), if necessary.

Saving Edit Changes

To save edit changes:

1. From the Choose Funct screen (one level above the Edit screen, two levels below

the top-level menu screen), select Save.

2. Choose whether you want to save to the Active, Customer 1, or Customer 2 area.

Use the scroll keys ( and ), if necessary.

Configuring the 10BaseT Port

To configure the 10BaseT port:

1. From the top-level menu screen, select Cnfig.

2. Select Activ.

3. Select Edit.

4. Select User.

5. Press F1 (Next) until the ENET Use configuration option appears.

6. Select the appropriate protocol for your network.

7. Press F1 (Next) until the ENET IP Adr configuration option appears.

8. Press F2 (Edit) to edit the IP address. You have the option of using F3 (Clear) to

reset the IP address to the factory default

000.000.000.000

9. Use the and keys to position the cursor under the digit you want to

change. Press F1 (Up) to increment the digit or F2 (Down) to decrement the digit.

10. Press F3 (Save) to save the value. Otherwise, the original value will be retained.

11. Return to editing the User configuration options. Press F1 (Next) until the ENET

NetMask configuration option appears.

12. Press F2 (Edit) to edit the subnet mask. Press F3 (Save) to save the value.

Configuring the DTE Port

Network DS0s must be mapped to the DTE port for DSX-1 voice to a PBX. To assign

Network DS0s 1 through 12 to the DTE port for voice traffic to a PBX:

1. From the top-level menu screen, select Cnfig.

2. Select Activ.

3. Select Edit.

4. Select DTE.

5. Using Table 1 as a guide make sure that the DTE port is enabled and that the

framing and coding are appropriate for the PBX. If the DTE port will not be used,

make sure that it is disabled.

Configuring the Data Ports

Network DS0s must be mapped to the Data Ports for data. To configure the DataPort:

1. From the top-level menu screen, select Cnfig.

2. Select Activ.

3. Select Edit.

4. Select Port.

5. Press the Function key under the port to be configured.

6. Using Table 2 as a guide, make sure that the proper port type is selected (V.35,

EIA 530, RS-449, or X.21).

7. Check any other options which may be needed.

Allocating Data Ports

To select the data port:

1. From the top-level menu screen, select Cnfig.

2. Select Activ.

3. Select Edit.

4. From the Edit screen, press the key until the Chan selection appears on the

screen.

5. Select Chan.

6. From the Channel Config screen, press the key to scroll the ports onto the

screen.

7. Select the desired port by pressing its corresponding Function key.

8. The configuration option for the data port channel allocation destination appears on

the screen. Select NET to assign this port to the network interface, select DTE to

assign this port to the DTE Drop/Insert (DSX-1) interface, or press the key and

the appropriate Function key to assign this port to another port.

9. Press F1 (Next) to display the appropriate configuration options on the screen. Use

one of the following examples, depending on whether you are assigning by block,

ACAMI, or individual channel.

Block or ACAMI Assignment Method

The Assign By configuration option screen appears after you select a port.

To assign by the block or ACAMI method:

1. Press F2 for Block or F3 for ACAMI.

2. Press F1 (Next) to display the next configuration option (Port Rate).

3. Use the or key to scroll the desired port rate onto the screen. Rates scroll

in groups of three. Available selections depend on the current base rate selected

for the port. Press the corresponding Function key to select the port rate. Then,

select Next to display the Start At configuration option on the screen.

NOTE: For port-to-port mapping, the procedure is complete after the port rate is

selected.

4. The Start At screen displays the configuration option used to select the starting

DS0 channel. If the destination selected is the network interface, then the network

channels appear on the screen. If the destination selected is the DTE Drop/Insert

(DSX-1) interface, then these channels appear on the screen.

Use the or key to scroll the desired channel onto the screen. Use the

Function keys to select the starting channel. Only those DS0 channel numbers that

provide enough bandwidth (based on the configured data rate) to be used as a

starting channel number are displayed. Channel allocation for this port can only be

cleared by selecting Clear.

Individual Channel Assignment Method

The Assign By configuration option screen appears after you select a port. To assign by

the individual channel method:

1. Press the key once to bring the Chan selection onto the screen.

2. Press F3 (Chan).

3. Press F1 (Next) to display the next configuration option (channel allocation).

4. Line 1 displays the 24 channels for the network interface or the DTE Drop/Insert

(DSX-1) interface, depending on which destination was chosen. Pressing the or

key scrolls the channels onto the screen in groups of three. Select the channel

by pressing the Function key under the desired number. Port

appears. The port is

assigned to that channel. To deallocate a port, press the Function key under that

port number.

Allocating DS0 Channels from the DTE Drop/Insert Interface to the

Network Interface

By using the configuration options, you can allocate DS0 channels from the DTE

Drop/Insert (DSX-1) interface to the network interface and specify which DS0 channels

carry Robbed Bit Signaling (RBS) information for voice channels.

To allocate DS0 channels from the DTE Drop/Insert (DSX-1) interface to the network

interface:

1. From the top-level menu screen, select Cnfig.

2. Select Activ.

3. Select Edit.

4. From the Edit screen, press the key until the Chan selection appears on the

screen.

5. Select Chan.

6. From the Channel Config screen, select DTE.

7. From the DTE Channels screen, press F1 to select Assign.

8. Press the Function key below the network channel desired. Each time that you

press the Function key, the DTE channel number is incremented. If the network

channel is currently unassigned (‘‘–” is displayed on Line 2), the DTE channel

number initially displays the same number as the corresponding network channel

number. However, if the network channel is currently assigned, the DTE channel

number is shown as D

Pressing the Function key for D24 wraps the display back

to D1. Only those channels that are not already assigned appear on the LCD when

scrolling. The network channels assigned to ports (Prt1...Prt4) are unavailable for

assignment.

To specify DTE Drop/Insert (DSX-1) channels used to carry voice information,

1. Press from the channel allocation screen to return to the DTE Channels

screen.

2. From the DTE Channels screen, press F2 to select Voice.

3. Line 1 displays the 24 DS0 channels for the DTE Drop/Insert (DSX-1) interface.

Pressing the or key scrolls the channels onto the screen in groups of three.

Line 2 displays whether the DS0 channel in Line 1 is a data channel (Data) or a

voice (RBS) channel. Each time that you press the Function key located below the

desired channel, the display in Line 2 toggles between Data and RBS.

Otros manuales para ACCULINK 3160

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de red de Paradyne

Paradyne

Paradyne FrameSaver NP 64+ Manual de usuario

Paradyne

Paradyne COMSPHERE 3610 Manual de operación y mantenimiento

Paradyne

Paradyne Comsphere 3510 Manual de usuario

Paradyne

Paradyne 5030 Manual de usuario

Paradyne

Paradyne COMSPHERE 3610 Manual de usuario

Paradyne

Paradyne COMSPHERE 3610 Manual de operación y mantenimiento

Paradyne

Paradyne COMSPHERE 3800 Series Manual de instrucciones

Paradyne

Paradyne HotWire 5246 Manual de usuario

Paradyne

Paradyne MIM-4E1 Manual de usuario

Paradyne

Paradyne FrameSaver SLV 9626 Manual de usuario

Paradyne

Paradyne JetFusion 2008 Manual de usuario

Paradyne

Paradyne Hotwire 5620 Manual de usuario

Paradyne

Paradyne Jetstream CPX-1000 Manual de usuario

Paradyne

Paradyne COMSPHERE 3800PLUS Manual

Paradyne

Paradyne HotWire 7924 Manual de usuario

Paradyne

Paradyne Jetstream CPX-1000 Manual de usuario

Paradyne

Paradyne Hotwire 5620 Manual de usuario

Paradyne

Paradyne 8540 Manual de usuario

Paradyne

Paradyne Fan Tray Assembly 8820-S3-900 Manual de usuario

Paradyne

Paradyne Comsphere 3510 Manual de operación y mantenimiento

Paradyne

Paradyne COMSPHERE 3610 Manual de usuario

Paradyne

Paradyne JetFusion 2208 Manual de usuario

Paradyne

Paradyne Hotwire 5216 Manual de usuario

Paradyne

Paradyne Hotwire 6210 Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario