Paradyne iMarc DSL 9720 CSU/DSU Manual de usuario
1
iMarc™DSL 9720 CSU/DSU
Installation Instructions
Document Number 9720-A2-GN10-10
May 2003
Contents
iMarc DSL CSU/DSU Overview .................................................................... 2
Upgrading a Unit to Advanced SLM Feature Set .......................................... 3
Product Documentation Online ..................................................................... 3
Package Checklist ........................................................................................ 3
Wiring and Cables You May Need ................................................................ 4
Installing the CSU/DSU ................................................................................ 5
Power-On ...................................................................................................... 10
Status LEDs .................................................................................................. 11
Troubleshooting ............................................................................................ 12
Configuration Setup ...................................................................................... 13
Verifying that Self-Test Passed ..................................................................... 14
Menu Navigation ........................................................................................... 15
Menu Hierarchy ............................................................................................ 15
Using the Easy Install Screen ....................................................................... 18
Completing Setup From the NOC ................................................................. 20
Cables and Connectors ................................................................................ 22
iMarc DSL 9720 CSU/DSU Technical Specifications .................................... 28
Important Safety Instructions ........................................................................ 29
Government Requirements ........................................................................... 30
Warranty, Sales, Service, and Training Information ...................................... 31
NOTE:
In this document, CSU/DSU refers to the line termination capability of the DSL
endpoint, and does not imply association with traditional T1 or DDS equipment.
NOTE: The FrameSaver®
product line has been
renamed to iMarc.
2
iMarc DSL CSU/DSU Overview
The iMarc™DSL (Digital Subscriber Line) CSU/DSU is a component in the iMarc
system. This system allows you to perform end-to-end service level management
across a hybrid DSL/Frame Relay network. Service providers can isolate and correct
problems remotely from their NOC (Network Operations Center).
The CSU/DSU has an IDSL interface and is a manageable frame relay-aware endpoint.
The following diagram shows a typical use of the iMarc DSL CSU/DSU in a network.
The iMarc DSL CSU/DSU is available in two feature sets:
Diagnostic Feature Set provides basic frame relay and diagnostic capability.
Advanced SLM (Service Level Management) Feature Set provides basic features,
plus service level management and reporting capability.
Refer to System Overview in the iMarc SLV Technical Description for a list of iMarc DSL
CSU/DSU’s features, and the capabilities provided by each feature set.
Frame
Relay
CPE
Router/
FRAD
DSL ATM
Access
Network
iMarc
xDSL Unit
03-17390
Frame
Relay DSL
ALARMS
MajorMinor
Fan
B
A
POWER
SERIAL
SMCM
CLOCK
A
ALARM
24681012141618
1357911131517
LAN/WANSLOT
B
CLOCK
B
A
SERIAL
MCC
AC
ALARM
48VRTN
48VNEG
POWERENTRYMODULE
LEFTUNIT:LINEA
RIGHTUNIT:LINEB
WARNING!
POWERMUSTBEDISCONNECTEDATTHESOURCE
BEFOREREMOVINGORINSTALLINGTHISPWRENTRYMODULE
48VRTN
48VNEG
POWERENTRYMODULE
LEFTUNIT:LINEA
RIGHTUNIT:LINEB
WARNING!
POWERMUSTBEDISCONNECTEDATTHESOURCE
BEFOREREMOVINGORINSTALLINGTHISPWRENTRYMODULE
AT M
Switch
Copper
Loop
AT M
PVC
AT M
Switch
Customer Premises –
Remote Site DSLAM
TDM
Access
Network
FR Network
FR/ATM
IWF
AT M
Switches FR
Switches
Frame Relay NSP’s Network
DHCP
Server
Router
iMarc
Endpoint
Customer Premises –
HQ Site
LAN
Frame Relay
NSP's
Network
Operations
Center
OpenLane
NMS
DSL Provider's
Network
Operations
Center
OpenLane
NMS
3
Upgrading a Unit to Advanced SLM Feature Set
An iMarc DSL CSU/DSU with the Diagnostic Feature Set can be upgraded to the
Advanced SLM Feature Set at any time by ordering an iMarc Advanced SLM Activation
Certificate (Feature Number 9720-C1-220). A certificate can be ordered for a single
CSU/DSU, or for many CSU/DSUs. You must specify the model to be activated, your
OpenLane SLM system license key number, and the number of router activations to be
included on the certificate.
The OpenLane®SLM system, Release 5.3 or later, is required to schedule the activation
of Advanced SLM features and to manage the certificate activations included in the
certificate.
To learn more about activating Advanced SLM capability, refer to the iMarc SLV
Activation Instructions (Document No. 9000-A2-GK43), or contact your sales
representative.
Product Documentation Online
Complete documentation for this product is available at www.paradyne.com.
Select Library →Technical Manuals →iMarc IP/Frame Relay Devices.
Select the following documents:
iMarc SLV Technical Description (9000-A2-GB30)
iMarc SLV Configuration Reference (9000-A2-GB31)
iMarc SLV SNMP Reference (9000-A2-GB32)
iMarc SLV Operations Guide (9000-A2-GB33)
To order a paper copy of a Paradyne document:
Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)
Outside the U.S.A., call 1-727-530-8623
Package Checklist
In addition to these instructions, verify that your package contains the following:
❑iMarc DSL CSU/DSU
❑Power cord with power transformer
❑Cable tie for power cord strain relief
❑DSL network access cable (U.S. models only)
Be sure to register your warranty at www.paradyne.com/warranty.
4
Wiring and Cables You May Need
The following wiring and cables are used with this product, which uses standard
interface connectors:
❑Standard connectors: An 8-position, RJ49C-type modular wall jack for the DSL
network connection. Pins 4 and 5 are used for Ring and Tip, respectively.
❑DSL wiring: Unshielded twisted-pair wiring (CAT3, or better). The CAT3 wiring must
meet EIA/TIA-568 specifications with 24 AWG (.5 mm) or 26 AWG (.4 mm).
❑Ethernet wiring: Twisted-pair wiring (CAT5, or better). The CAT5 wiring must meet
EIA/TIA-568 specifications with 24 AWG (.5 mm) or 26 AWG (.4 mm).
For standard cables, refer to Cables and Connectors on page 22 for standard pin
numbers. For Paradyne cables, contact your sales representative to order them.
Interface
Connection Cables
Feature or
Part Number
COM
Communication
port to a PC or
asynchronous
terminal
Shielded DB9-to-DB9, Standard EIA-232
straight-through cable —
ETHERNET
Ethernet port to a
NIC on a PC or an
Ethernet hub
For connection to a PC NIC:
Standard Ethernet crossover cable 9008-F1-550
For connection to an Ethernet Hub:
Standard Ethernet straight-through cable 035-0349-1431
PORT
User data port to a
DTE
Shielded standard straight-through
DB25-to-DB25 cable for EIA-530-A
For V.35, add DB25-to-MS34 cable, or
DB25-to-MS34 adapter
For X.21, add DB25-to-DB15 adapter
—
3100-F1-570
3100-F1-572
3100-F1-571
NET
Network port to the
DSL wall jack
Standard straight-through RJ49C-type DSL
network cable with 8-pin modular connectors.
Supplied with U.S. models.
3100-F1-500
5
Installing the CSU/DSU
Place the iMarc DSL CSU/DSU on a flat surface with clearance for the rear connectors.
Procedure
1. Use an 8-pin modular straight-through cable for the network connection. Insert one
end of the cable into the jack labeled NET. Insert the other end into the wall jack for
DSL data communications.
DSL
Network
02-17315
ETHERNET
P
O
R
T
COM
POWER
NET
NET
6
2. Use an 8-pin Ethernet cable for the Ethernet connection for local management.
Insert one end of the cable into the jack labeled ETHERNET.
— Use a straight-through cable to connect the other end of the cable to an
Ethernet hub. Do not connect to the hub’s optional Uplink connection with a
straight-through cable; the Uplink connection requires an Ethernet crossover
cable.
– or –
— Use an Ethernet crossover cable to connect to a PC with an Ethernet Network
Interface Card (NIC) installed, or to a hub’s Uplink connection.
02-17316
Hub
ETHERNET
P
O
R
T
COM
POWER
NET
Ethernet
Straight-Through
Cable
ETHERNET
7
3. Connect one end of the DTE’s cable to the user data port labeled PORT. Tighten
the screws on each side of the connector. Attach a cable adapter, if required. (See
Wiring and Cables You May Need on page 4.) Plug the other end of the cable or
adapter into the DTE (router or FRAD).
02-17317
ETHERNET
P
O
R
T
COM
POWER
NET
DTE
PORT
8
4. Use a VT100-compatible asynchronous terminal or a PC to set up management
access to the unit. Insert the DB9 plug end of an EIA-232 cable into the CSU/DSU’s
COM port. Tighten the screws on each side of the connector. Insert the other end of
the cable into the terminal or PC.
The terminal or PC’s configuration must be compatible with the CSU/DSU’s. Refer
to the procedure on page 13 under Configuration Setup. If connecting an external
modem to the COM port, refer to Connecting an External Modem on page 27.
COM
Port
02-17318
ETHERNET
P
O
R
T
COM
POWER
NET
VT100
Terminal
9
5. Insert the supplied power cord’s round end into the jack labeled POWER.
Depending on the model, your power supply plugs directly into a grounded outlet or
has a detachable cord that plugs into an outlet.
— If you have a wall-mount transformer, plug the transformer into a grounded AC
outlet.
— If you have a table-top transformer, verify that the cord is firmly attached to the
transformer, and plug the other end of the cord into a grounded AC outlet.
Install the supplied tie wrap for strain relief, as shown.
Installation of the hardware is now complete. When the power cord is installed, the
CSU/DSU goes through a power-on self-test.
02-17319
ETHERNET
P
O
R
T
COM
POWER
NET
rounded
Power
Outlet
Tie
Wrap
Power
Jack
10
Power-On
When power is applied, the CSU/DSU performs self-diagnostics and the PWR LED is
on. The self-diagnostics include a power-on self-test where all of the LEDs are on.
Refer to Status LEDs on page 11 for information about the LEDs. Refer to
Troubleshooting on page 12 for LED indications requiring action.
iMarc DSL 9720 CSU/DSU
03 17411
OK
OK
ALM
TEST
FR
DSL
NetworkSystem Por t
9720
DSL
IDSL
R
Tabla de contenidos
Otros manuales de Hardware de red de Paradyne
Paradyne
Paradyne 7510-A2-GB20-00 727 Manual de usuario
Paradyne
Paradyne Hotwire 8775 Manual de usuario
Paradyne
Paradyne COMSPHERE 6700 Series Manual de usuario
Paradyne
Paradyne COMSPHERE 6700 Series Manual de usuario
Paradyne
Paradyne ACCULINK 3151 CSU Manual de usuario
Paradyne
Paradyne 4929 DSLAM Manual de usuario
Paradyne
Paradyne 7915-A1 E1 SDSL Manual de usuario
Paradyne
Paradyne COMSPHERE 3550 Series Manual de usuario
Paradyne
Paradyne 8310 MVLt Manual de usuario
Paradyne
Paradyne COMSPHERE 6700 Series Manual de usuario
Paradyne
Paradyne Hotwire 5446 Manual de usuario
Paradyne
Paradyne 9126 Manual de usuario
Paradyne
Paradyne 24-Port SHDSL Mini DSLAM SMD2000-24T Manual de usuario
Paradyne
Paradyne Hotwire 8784 Manual de usuario
Paradyne
Paradyne HotWire 8800 DSLAM Manual de usuario
Paradyne
Paradyne Hotwire 7995 Manual de usuario
Paradyne
Paradyne Comsphere 3510 Manual de usuario
Paradyne
Paradyne COMSPHERE 3610 Manual de usuario
Paradyne
Paradyne COMSPHERE 3610 Guía del usuario
Paradyne
Paradyne ACCULINK 3160 Manual
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
