ParaBody 841101 Manual de usuario

841101 WEIGHT STACK OPTION

CLASSH

PART # 6754401

REV.A

Version: 841101

Revision: 06/19/01

ASSEMBLY INSTRUCTIONS

IMPORTANT NOTES

Please note:

Tools Required forAssembly

* Thank you for purchasing the Parabody 841101 WEIGHT STACK OPTION. Please read these

instructions thoroughly and keep them for future reference. This product must be assembled on

a flat, level surface to assure its proper function.

* 3/4” wrench

* 9/16” wrench

* Ratchet with 3/4” and 9/16” sockets

* Adjustable wrench

* Tape measure

NOTE:BOLTLENGTHISMEASURED FROMTHEUNDERSIDEOFTHEHEADOFTHE BOLT.

BOLT LENGTH RULER:

We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy

water. Touch-up paint can be purchased from your Parabody customer service representative

at (800) 328-9714.

BoltLengthRuler

0123456

1/2 1/2 1/2 1/2 1/2 1/2

WELCOMETOTHEWORLDOF Serious steel!

There is a risk assumed by individuals who use this type of equipment. To minimize risk, please

follow these rules:

2. Do not allow minors or children to play on or around this equipment.

1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.

Failure to do so may result in serious injury.

3. Exercise with care to avoid injury.

4. If unsure of proper use of equipment, call your local Parabody distributor or call the

Parabody customer service department at (800) 328-9714.

BOLT LENGTH

5. Consult a physician before beginning any exercise program.

PARTS LIST

PART #

6750803

6753703

6274402

6275302

6609002

6610402

6750503

6176201

6754501

6189501

3116101

3116201

6284501

6714601

6758701

6577701

6542402

3103102

3108002

6595201

3117401

6467001

KEY

QTY

PART #

3102901

3102933

3102922

3102904

3102915

3102910

3102502

3102801

3102501

3102802

6480301

6692601

3119301

6405201

6236701

6177001

6214401

3013801

6075906

6382301

6214501

DESCRIPTION

3/8 X 1-1/4” BOLT

3/8 X 2” BOLT

3/8 X 2-3/4” BOLT

3/8 X 3” BOLT

3/8 X 3-1/4” BOLT

1/2 X 3” BOLT

1/2” WASHER

1/2” LOCK NUT

3/8” WASHER

3/8” LOCK NUT

3/8” FLANGE SPACER

3 X 2” END CAP

2-1/2” ROUND END CAP

2” SQ. END CAP

1-3/4” SQ. END CAP

NON-SKID STRIP

SELECTOR PIN

5/16” SNAP LINK

12 LINK CHAIN

PLATE BUSHING 10 CT

WEIGHT PLATE

QTY

DESCRIPTION

UPRIGHT

TOP BOOM

LOW ROW BAR

LAT BAR

LOW ROW ATTACHMENT

KNEE SUPPORT

WEIGHT STACK BASE

ROLLER PAD

79-1/2” GUIDE ROD

WEIGHT STACK LABEL

4-1/2” PULLEY

3-1/2” PULLEY

WEIGHT STACK SHAFT

HEAD PLATE

LAT CABLE

LOW ROW CABLE

1-3/4” X 5-1/4” PLATE

1 X 8” GRIP

WEIGHT STACK CUSHION

GUIDE ROD BUSHING

CAP PLUG

2” SQ COVER CAP

KEY

FIGURE 1

STEP 1:

• Insert two 2-1/2” ROUND END CAPS (35) to the LOW ROWATTACHMENT (5) as shown in FIGURE 1.

• Attach two NON-SKID STRIPS (38) to the LOW ROW ATTACHMENT (5) as shown in FIGURE 1.

38 35

FIGURE 2

STEP 2:

• SECURELY assemble the LOW ROWATTACHMENT (5) and the UPRIGHT (1) to the POWER RACK using two 3/8 X 3-1/4”

BOLTS (27), four 3/8” WASHERS (31), and two 3/8” LOCK NUTS (32). See FIGURE 2.

0123456

1/2 1/2 1/2 1/2 1/2 1/2

POWER RACK

• Insert two 2” SQ ENDCAPS (36) into the ends of the UPRIGHT (1) as shown in FIGURE 2.

3/8 X 3-1/4” 27

FIGURE 4

• Insert two WEIGHT PLATE BUSHINGS (42) into

the “PARABODY” side of each of the twenty

WEIGHT PLATES (43) as shown in FIGURE 4.

STEP 4

FIGURE 3

STEP 3

• Slide one 2” SQ. COVER CAP (22) over the end of the WEIGHT STACK BASE (7) as shown in FIGURE 3.

• SECURELY assemble the WEIGHT STACK BASE (7) to the UPRIGHT (1) using two 1/2 X 3” BOLTS (28), two 1/2” WASH-

ERS (29), and two 1/2” LOCK NUTS (30) as shown in FIGURE 3.

1/2 X 3” 28

• Insert four CAP PLUGS (21) into the bottom end & top end of the two GUIDE RODS (9) as shown in FIGURE 5.

STEP 5:

FIGURE 5

23 3/8 X 1-1/4” 13

• Insert two GUIDE RODS (9) into the WEIGHT STACK BASE (7) as shown on FIGURE 5. (NOTE: Lubricate GUIDE RODS

(9) with silicon or teflon spray available at most hardware stores.)

• Slide two WEIGHT STACK CUSHIONS (19) down over the GUIDE RODS (9).

• Securely assemble the WEIGHT STACK SHAFT (13) to the HEAD PLATE (14) using one 3/8 X 1-1/4” BOLT (23) and one 3/8”

WASHER (31).

• Using EXTREME CARE slide all twenty WEIGHT PLATES (43) down over the GUIDE RODS (9) on to the WEIGHT STACK

CUSHIONS (19). Make sure that the keyholes of the WEIGHT PLATES (43) are all facing the right way.

• Attach the WEIGHT STACK LABELS (10) to the WEIGHT STACK. Also insert the WEIGHT STACK SELECTOR PIN (39) into

the first WEIGHT PLATE (43) of the WEIGHT STACK.

• CAREFULLY slide the HEAD PLATE ASSEMBLY down over the GUIDE RODS (9) onto the WEIGHT STACK.

0123456

1/2 1/2 1/2 1/2 1/2 1/2

• SECURELY assemble two 3-1/2” PULLEYS (12) to the TOP BOOM (2) using two 3/8 X 2-3/4” BOLTS (25), four 3/8”

FLANGE SPACERS (33), and two 3/8” LOCK NUTS (32). See FIGURE 6. (NOTE: BEFORE TIGHTENING, MAKE SURE

CABLE (15) IS IN THE GROOVES OF THE PULLEYS.)

STEP 6:

• Insert two 2 X 3” END CAPS (34) into the TOP BOOM (2) as shown in FIGURE 6.

• Route threaded end of the LAT CABLE (15) through the TOP BOOM (2) as shown in FIGURE 6.

FIGURE 6

• Insert two GUIDE ROD BUSHINGS (20) into the BUSHINGS of the TOP BOOM (2) as shown in FIGURE 6.

FIGURE 7

STEP 7

• LOOSELY assemble two 3-1/2” PULLEYS (12) to two 1-3/4” X

5-1/4” PLATES (17) using two 3/8 X 2” BOLTS (24) and two 3/8”

LOCK NUTS (32) as shown in FIGURE 7.

24 3/8 X 2”

25 3/8 X 2-3/4”

STEP 8:

FIGURE 8

• SECURELY assemble two 3-1/2” PULLEYS (12) to the TOP BOOM (2) using two 3/8 X 2-3/4” BOLTS (25), four 3/8”

FLANGE SPACERS (33), and two 3/8” LOCK NUTS (32). See FIGURE 8. (NOTE: BEFORE TIGHTENING, MAKE SURE

CABLE (15) IS IN THE GROOVES OF THE PULLEYS.)

• Route threaded end of the LAT CABLE (15) around the one of the PULLEYS in PLATE & PULLEY ASSEMBLY (17) and

through the holes in the TOP BOOM (2) as shown in FIGURE 8.

25 3/8 X 2-3/4”

STEP 9:

FIGURE 9

• Swing the GUIDE RODS (9) under the TOP BOOM (2) as shown on FIGURE 9.

• Assemble the TOP BOOM (2) over the GUIDE RODS (9) and SECURELY assemble the TOP BOOM (2) to the UPRIGHT (1)

using two 1/2 X 3” BOLTS (28), two 1/2” WASHERS (29), and one 1/2” LOCK NUT (30). See FIGURE 9.

• SECURELY assemble the TOP BOOM (2) to the top of the POWER RACK using two 3/8 X 3” BOLTS (26), four 3/8” WASH-

ERS (31), and two 3/8” LOCK NUTS (32). See FIGURE 9.

• Screw the threaded end of the LAT CABLE (15) approximately 3/4” into the end of the WEIGHT STACK SHAFT (13) and tighten

jam nut securely. See FIGURE 9.

3/8 X 3” 26

1/2 X 3” 28

POWER RACK

FIGURE 10

STEP 10:

3/8 X 2-3/4” 25

• Loop the ball end of the LOW ROW CABLE (16) around one 4-1/2” PULLEY (11) and SECURELY assemble the 4-1/2” PUL-

LEY (11) to the UPRIGHT (1) using two 3/8 X 2-3/4” BOLTS (25), two 3/8” FLANGE SPACERS (33), two 3/8” WASHERS

(31), and two 3/8” LOCKNUTS (32). (NOTE: Make sure CABLE is routed between the PULLEY and the retaining bolt as

shown in FIGURE 10.)

Otros manuales para 841101

Tabla de contenidos

Otros manuales de Gimnasio en casa de ParaBody

ParaBody

ParaBody GS4 Manual de usuario

ParaBody

ParaBody 841101 Manual de usuario

ParaBody

ParaBody 426103 Manual de usuario

ParaBody

ParaBody 350 Manual de usuario

ParaBody

ParaBody 880 Manual de usuario

ParaBody

ParaBody 917101 Manual de usuario

ParaBody

ParaBody 93 Manual de usuario

ParaBody

ParaBody 445103 Manual de usuario

ParaBody

ParaBody 205101 Manual de usuario

ParaBody

ParaBody PBF849 Manual de usuario

ParaBody

ParaBody 250101 Manual de usuario

ParaBody

ParaBody 893101 Manual de usuario

ParaBody

ParaBody 425104 Manual de usuario

ParaBody

ParaBody 945101 Manual de usuario

ParaBody

ParaBody 843 Manual de usuario

ParaBody

ParaBody PBF460 Manual de usuario

ParaBody

ParaBody 813 Manual de usuario

ParaBody

ParaBody 835 Manual de usuario

ParaBody

ParaBody GS6 Manual de usuario

ParaBody

ParaBody PBF064 Manual de usuario

ParaBody

ParaBody 458 Manual de usuario

ParaBody

ParaBody PBF351 Manual de usuario

ParaBody

ParaBody 405 Manual de usuario

ParaBody

ParaBody PBF065 Manual de usuario

Manuales populares de Gimnasio en casa de otras marcas

Horizon Fitness

Horizon Fitness OXFORD 6 Manual de usuario

Energetics

Energetics Multi Trainer 5.1 Manual de usuario

Matrix

Matrix MG-PL Series Manual de usuario

Reebok

Reebok Tbr2i Manual de operación y mantenimiento

Weider

Weider 8300 Hard Drive Manual de usuario

Pure Fitness

Pure Fitness 8526HE Manual de usuario

Weider

Weider 8700 I Guía de inicio rápido

Bowflex

Bowflex Sport 001-6961 Manual de usuario

NordicTrack

NordicTrack E8200 Competition Bench Guía de inicio rápido

Weider

Weider WEMC10161 Manual de usuario

Body Solid

Body Solid GHYP-345 Manual de usuario

Evo

Evo TAHOE 5105 Manual de usuario

cardiobull

cardiobull RA17 Manual de usuario

JLL

JLL Ventus Pro Air Power Manual de usuario

Trojan

Trojan Colorado 370 Manual de usuario

Octane Fitness

Octane Fitness xRide xR650 Manual de usuario

Precor

Precor Discovery Series Manual de usuario

Insportline

Insportline RW600 Manual de usuario