Panasonic MC-E7111-AE79 Manual de usuario
©2006 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
MC-E7111-AE79
MC-E7111-AE7A
MC-E7111-RE79
MC-E7111-RW79
MC-E7111-AW79
MC-E7113-RE79
MC-E7113-RW79
Product Color
(B)Deep Blue : MC-E7111-AE79, MC-E7111-AE7A,
MC-E7111-AW79
(R)Deep Red : MC-E7111-RE79, MC-E7111-RW79,
MC-E7113-RE79, MC-E7113-RW79
Destination Europe
Vacuum Cleaner
Specifications
Order No ECD0602002C2
1 Name of parts
MODEL MC-E7113, MC-E7111
3
MC-E7111-AE79 / MC-E7111-AE7A / MC-E7111-RE79 / MC-E7111-RW79 / MC-E7111-AW79 / MC-E7113-RE79 / MC-E7113-RW79
4
MC-E7111-AE79 / MC-E7111-AE7A / MC-E7111-RE79 / MC-E7111-RW79 / MC-E7111-AW79 / MC-E7113-RE79 / MC-E7113-RW79
4 TROUBLE SHOOTING GUIDE
CONDITION CHECHPOINT METHOD OF INSPECTION CAUSE/REMEDY
Motor fails rotate
(no noise heard at all). Power cord connection Chech power cord continuity
between pliug pins cord reel ass´y. If there is no continuity, replace
the cord reel ass´y.
Fuse (250V, 12A) Chech fuse continuity. If there is no continuity, replace
the fuse.
Motor continuity Chech motor contiuity between
carbon brush holder tabs. If there is no continuity, replace
the motor.
On/OFF Switch Chech continuity across switch
connections. If there is no continuity, replace
ON/OFF Switch.
Control circuit board (P.C.B. Au) If other checkpoints do not have any problems, then replace the
control circuit board Au (P.C.B. Au).
Motor runs but there is no suction. Hose or Suction inlet Chech if there is any blockage in
the hose or suction inlet. lf therer is any blockage, remove
it.
Dust bag / Central filter Chech if dust bag is full or dust
accumulated in central filter. If the paper bag is full, replace it. If
the central filter is dirt, clean or
replace it.
Noise or vibration Motor fan Chech dust accumulated in motor
fan (it could happen if the vacuum
cleaner has been used with a
broken dust bag or without central
filter).
if the is dust accumulated in the
motor fan, replace the motor and
chech filter condition (never try to
dismantle the motor fan).
6
MC-E7111-AE79 / MC-E7111-AE7A / MC-E7111-RE79 / MC-E7111-RW79 / MC-E7111-AW79 / MC-E7113-RE79 / MC-E7113-RW79
5.1. Separate the upper and lower
bodies.
1.Remove the attachment nozzle and cover fitted to the rear
of the body.
2.Remove the screw fixing the body cover and remove the
body cover.
3.Open the dust cover assembly and remove the grip.
4.Turn the body over and remove the two screws at the rear
fixing the upper and lower bodies.
* These are special screws. Use a TORX screwdriver.
(If there are no TORX screwdrivers, then use a thin flat-
blade screwdriver that fits the screw slot.)
5.Turn the body over again for normal positioning. Open the
dust cover assembly and remove the four screws fixing the
upper and lower bodies.
6.Lift the upper body to separate it from the lower body.
5 How to replace major components
Important notice: Before replacing any components, make sure to turn OFF the vacuum cleaner.
Remove the power plug from the outlet.
7
MC-E7111-AE79 / MC-E7111-AE7A / MC-E7111-RE79 / MC-E7111-RW79 / MC-E7111-AW79 / MC-E7113-RE79 / MC-E7113-RW79
5.2. Dust cover assembly removal
1.Separate the upper and lower bodies.
2.Push the salient with a flat-blade screwdriver to remove it
while the upper body is turned over. Pull and remove the
dust cover.
* Salient position
5.3. Motor removal
1. Lift the motor to remove it from the lower body.
2.Remove the ancillary components around the fast-on
terminal connected to the motor.
3.Motor ancillary component removal
Remove the front and rear motor support rubber and noise
suppressor, etc., and replace the motor.
4.Assembling
Take the revers order of removing procedure.
8
MC-E7111-AE79 / MC-E7111-AE7A / MC-E7111-RE79 / MC-E7111-RW79 / MC-E7111-AW79 / MC-E7113-RE79 / MC-E7113-RW79
1.When the motor is removed from the lower body, straightly
pull up the cord reel from the lower body for removal.
2.Disconnect the lead wires from the connection terminals
(Faston terminals) of the cord reel on the body partition.
3.Remove the cord guide fitted on the body lower unit. Then,
remove the power cord by pulling it out to separate Lower
body from Cord reel ass´y.
4.Pro-wind the cord reel ass’y 2 times in the direction of the
arrow (→) indicated on the cord reel cover.
5.With the brake lever section down, fit the cord reel ass’y
into the lower body.
5.4. Replacing cord reel
9
MC-E7111-AE79 / MC-E7111-AE7A / MC-E7111-RE79 / MC-E7111-RW79 / MC-E7111-AW79 / MC-E7113-RE79 / MC-E7113-RW79
5.5. Printed circuit board AU
removal
1.Open the upper body. Disengage the two lead wires
connecting the ON/OFF switch to the P.C.B. A Unit.
2.Remove the two screws fixing the P.C.B. A Unit. Remove
the P.C.B. A Unit together with the components surrounding
it from the upper body.
5.6. Fuse removal
1.Disengage the fuse lead wire connected to the ON/OFF
switch and remove the fuse.
10
MC-E7111-AE79 / MC-E7111-AE7A / MC-E7111-RE79 / MC-E7111-RW79 / MC-E7111-AW79 / MC-E7113-RE79 / MC-E7113-RW79
1.Remove the three A packings at the section where the
ON/OFF switch is fitted.
2.Find the three switch pedal tabs hooked to the section
where the three A packings were removed.
Unhook the tabs using a flat-blade screwdriver.
* If any of the tabs cannot be unhooked, then break
them to remove them.
3.Remove the screw fixing the switch cover to remove the
switch cover and the switch.
4.In order to fit a new switch, assemble the unit by carrying
out the disassembly procedure in reverse.
Assemble the switch, switch cover, and the switch spring
into a switch pedal. Then, push the switch pedal into the
upper body.
5.7. ON/OFF switch removal
11
MC-E7111-AE79 / MC-E7111-AE7A / MC-E7111-RE79 / MC-E7111-RW79 / MC-E7111-AW79 / MC-E7113-RE79 / MC-E7113-RW79
6.1.2. PARTS LIST (ATTACHMENT)
Ref. No. Part No. Part Name & Description Remarks
A-1 AMC99R-UW00E FLOOR NOZZLE ASSY.(PLASTIC)
A-2 AMC94P-UW00E HOSE ASSEMBLY
A-3 AMC13P-UW00E EXTENSION WAND A(PLASTIC) MC-E7111
A-3 AMC13P-UX00E EXTENSION WAND A MC-E7111 E7113
A-4 AMC40P-UW00E EXTENSION WAND(PLASTIC) MC-E7111
A-4 AMC40P-UX00E EXTENSION WAND MC-E7111 E7113
13
MC-E7111-AE79 / MC-E7111-AE7A / MC-E7111-RE79 / MC-E7111-RW79 / MC-E7111-AW79 / MC-E7113-RE79 / MC-E7113-RW79
Este manual sirve para los siguientes modelos
6
Tabla de contenidos
Otros manuales de Aspiradora de Panasonic
Panasonic
Panasonic MC-UG589-00 Manual de usuario
Panasonic
Panasonic MC-CL933 Manual de usuario
Panasonic
Panasonic EY3743B57 Manual de usuario
Panasonic
Panasonic MC-YL699-S146 Manual de usuario
Panasonic
Panasonic MCCL485 - CANISTER VACUUM - MULTI LANGUAGE Manual de usuario
Panasonic
Panasonic MC-V5737 Manual de usuario
Panasonic
Panasonic MC-GG529-00 Manual de usuario
Panasonic
Panasonic MCV7710 - UPRIGHT VACUUM-MULTI-LANG Manual de usuario
Panasonic
Panasonic MCV5203 - COMMERCIAL VACUUM Manual de usuario
Panasonic
Panasonic EY37A3 Manual de usuario
Panasonic
Panasonic MC-CG983 Manual de usuario
Panasonic
Panasonic MCV5237 - UPRIGHT VACUUM-QKDR Manual de usuario
Panasonic
Panasonic MC-V5009 Manual de usuario
Panasonic
Panasonic MCV6970 - UPRIGHT VACUUM-68 Manual de usuario
Panasonic
Panasonic MC-CG373 Manual de usuario
Panasonic
Panasonic MC-SB33J Manual de usuario
Panasonic
Panasonic MC-CL575 Manual de usuario
Panasonic
Panasonic Quickdraw MC-V7377 Manual de usuario
Panasonic
Panasonic QuickDraw MC-V5355 Manual de usuario
Panasonic
Panasonic MCV5261 - UPRIGHT VACUUM PLAT Manual de usuario
