Panasonic MC-E4101 Manual de usuario

rights reserved. Unauthorized copying and

distribution is a violation of law.

MC-E4101

MC-E4103

Destination : Europe

Vacuum Cleaner

Model MC-E4101 MC-E4103

Powe

source 230-240V 230-240V

50Hz 50Hz

Input powe

(IEC) 1400-1500W 1400-1500W

Mains lead length 6.7m 6.7m

Radius of opera

ion 7m 7m

Net weigh

6.5kg 6.5kg

Dimensions (L×W×H) 330×320×1100 330×320×1100

ttachments: Dusting brush * *

Crevice nozzle * *

Extension wand * *

Mini turbine nozzle - *

ttachment holde

- *

Speci

ications are subject to change Without notice for furthe

improvement

ORDER NO.ECD0503003C2

1 PICTORIAL DIAGRAM

MC-E4001/MC-E4003

2 SCHEMATIC DIAGRAM

MC-E4001/MC-E4003

3 REPLACEMENT OF MAIN

PARTS

IMPORTANT: Before replacing any part always

DISCONNECT THE CLEANER FROM THE ELECTRIClTY

SUPPLY.

3.1. MOTOR SHAFT BELT

1.Loosen 4 screws from the base plate and lift it off (Fig.1)

2.Remove the belt from the motor shaft and outer motor

pulley replacing with a new one.(Fig.2)

3.Re-install the new belt around the motor shaft and pulley.

4.Replace the base plate and refasten the screws.

3.2. BEATER BAR BELT

1.Remove the base plate and motor shaft belt as explained

previously in paragraph 3.1 Motor shaft belt, point 1-2.

2.Lift the beater bar assembly and remove the belt from the

beater bar pulley and motor pulley.(Fig.3)

3.Replace the belt with a new one and re-assemble in the

reverse order.

4.Insert the beater bar mounts into their housing and turn the

beater bar by hand to ensure the belts have been seated

correctly.(Fig.4)

5.Replace the base plate and refasten the screws.

3.3. BEATER BAR ASSEMBLY

1.Remove the base plate as explained previously in

paragraph 3.1 Motor shaft belt, point 1.

2.Lift the beater bar assembly and remove the belt from the

beater bar pulley. (Fig.5)

3.Replace the beater bar assembly with a new and place the

belt around the beater bar pulley.

4.Insert the beater bar mounts into their housings and turn the

beater bar by hand to ensure the belt has been seated

correctly.

5.Replace the base plate and refasten screws.

3.4. MOTOR PULLEY UNlT

1.Remove the base plate as explained previously in

paragraph 3.1 Motor shaft belt, point 1.

2.Release the two belts from the motor pulley.

3.Remove 1 screw from the pedal and take it out.(Fig.6)

4.Expand between floor nozzle cover and motor pully. Then

remove the pedal.

5.Remove 2 screws from the motor pulley unit and take it out.

(Fig.7)

6.Replace the motor pulley unit with a new one and re-install

it.

7.Re-assemble the pedal, belts and remaining parts in the

reverse order.

3.5. MOTOR

1.Remove base plate, pedal and motor pulley as explained

previously in paragraph 3.4 Motor pulley unit, points 1-4.

2.Insert a flat-head screwdriver between nozzle housing and

pry out the plastic shaft. (Fig.8).

3.And then remove the floor nozzle upper.

4.Remove nozzle cover, turn the vacuum cleaner over and

remove 4 screws from upper body and take it out. (Fig.9)

5.Take out the motor and remove two lead wires.

6.Remove front / rear motor supports rubber, noise absorber

and replace the motor with a new one.(Fig.11)

7.Re-assemble front / rear motor supports, noise absorber

and connect the lead wires to the motor.

8.Re-install the motor and reassemble upper body and

remaining parts in the reverse order.

NOTE: Make sure the lead wires are correctly positioned to

avoid pinching them between parts.

3.6. CARBON BRUSH

NOTE: Replace both carbon brushes at the same time.

1.Remove upper body and take out the motor as explained

previously in paragraph 3.5 Motor, points 1-4.

2.Remove 1 screw from the carbon brush holder and take it

out. (Fig.12)

3.Take out both of the carbon brush holder from the motor.

(Fig.13)

4.Replace the carbon brush holder with new one and insert

into the motor. (Fig.14)

5.Fasten a screw in the motor and fixed the carbon brush

holder.

6.Re-assemble front / rear motor supports, noise absorber

and connect the lead wires to the motor.

7.Re-install the motor and reassemble upper body and

remaining parts in the reverse order.

NOTE: Make sure the lead wires are correctly positioned to

avoid pinching them between parts.

3.7. THERMAL CUT-OUT

1.Remove upper body and take out the motor unit as

explained previously in paragraph 3.5 Motor, points 1-4.

2.Remove thermal cut-out connections from the motor.

(Fig.15)

3.Remove the thermal cut-out connection of P.C.B. (Power

P.C.B.) (Fig.16)

4.Replace the thermal cut-out with a new one and it connect

both P.C.B. and motor. (Fig.16)

3.8. MAIN FUSE

1.Remove hose end from rear body and remove three screws

of front body.

2.Remove protruded part of the end of front body. Then

remove front body. (Fig.17)

3.Take out main fuse unit and remove lead wires

connections. (Fig.19) (and 3 gaick connect terminals from

on-off switch and P.C.B unit.)

4.Replace the main fuse with a new one and connect the lead

wires refer to the schematic diagram.

5.Place the main fuse into the right place and reassemble the

front body and remaining parts in the reverse order.

NOTE: Make sure the lead wires are correctly positioned to

avoid pinching them between parts.

3.9. MAINS LEAD

1.Remove hose end and front body as explained previously in

paragraph 3.8 MAIN FUSE.

2.Remove mains lead connections and take it out. (Fig. 20)

NOTE: To release the terminal from the housing, use a

tool Ref.: VLJ-20 Supplied by JST.

3.Replace mains lead with a new one, and connect it refer to

the schematic diagram and re-install it. (Fig.21)

NOTE: Make sure the lead wires are correctly

positioned to avoid pinching them between parts.

4.Reassemble base suction inlet and remaining parts in the

reverse order.

3.10. ON/OFF SWlTCH

1.Remove hose end and front body as explained previously in

paragraph 3.8 MAIN FUSE.

2.Remove the lead wires (provided with quick-connect

terminal) from the switch tabs. (Fig.22)

3.Release switch claws with a flat-head screwdriver and take

it out. (Fig.23)

4.Replace ON/OFF Switch with a new one and re-install it.

5.Connect the lead wires refer to the schematic diagram and

reassemble base suction inlet and remaining parts in the

reverse order.

4 EXPLODED VIEW (BODY UNIT)

MC-E4101/E4103

5 PARTS LIST (BODY UNIT)

safety Ref. No. Part No. Part Name & Description Remarks

1 AMC95B-XD0AE Handle unit MC-E4101

1 AMC95B-XD0KE Handle unit MC-E4103

2 AMC32R-XD04E Attachment holder

3 AMC93E-XD0K8 Main lead(Power cord)

4 AMC61R-XD04E Crevice nozzle

5 AMC40P-XD04E Extention wand

6 AMC88R-XD04E Dusting brush unit

7 AMC84P-XC00E Hose unit MC-E4101

7 AMC84P-XD00E Hose unit MC-E4103

8 AMC82L-XD0AE Rear cover MC-E4101

8 AMC82L-XD0KE Rear cover MC-E4103

9 AMC42K-XJ0KE Filter case

10 AMC38K-XJ0WE Clean air filter MC-E4101

11 AMC95K-XL0WE HEPA filter MC-E4103

12 AMC67V-XD00E Lead wire A unit With Fuse

13 AMC84Q-XD00E Connecting hose unit

14 AMC73B-XD00E Handle screw

15 AMC33Z-XD00E Warning label

16 AMC01E-XD0KE ON/OFF Switch

17 AMC21A-XD0AE Rear body

17 AMC21A-XD0KE Rear body

18 XUB7FP Fixing washer

19 AMC01C-XD04E Wheel

20 AMC16C-XD00E Roller shaft

21 AMC30L-XD00E Outlet filter

22 AMC78A-XD00E Holder

23 AMC91F-XD00C PC BOARD W/Component

24 AMC98W-XD00E Thermal protector unit

25 AMC20A-XD0AE Front body MC-E4101

25 AMC20A-XD0KE Front body MC-E4103

26 AMC02F-XD00E Motor support rubber (front)

27 AMC92F-XD00C Fan motor unit 230-240V

28 AMC27F-XD00E Carbon brush

29 XTB3+8GFY Tapping screw

30 AMC10G-XD00E Noise absorber

31 AMC03F-XD00E Motor support rubber (rear)

32 AMC37K-XD00E Secondary filter

33 AMC32K-XD0KE Filter supporter

34 AMC97K-KD00E Protector unit

35 AMC09M-XD00E Indicator packing

36 AMC99F-XC02E Motor case U MC-E4101

36 AMC99F-XD0SE Motor case U MC-E4103

37 AMC31A-XD04E Furniture guard

38 AMC25S-XD00E Plastic holder

39 AMC98R-XD0AE Floor nozzle upper unit MC-E4101

39 AMC98R-XD0KE Floor nozzle upper unit MC-E4103

40 AMC47A-XD04E Pedal left/handle release

41 AMC51A-XD00E Pedal shaft

42 AMC58A-XD00E Pedal spring right

43 AMC39S-XD00E Belt B

44 AMC28S-XD00E Belt

45 AMC90S-XD00E Idler pulley

46 AMC54R-XD00E End plate

47 AMC06R-XD00E Pipe felt

48 AMC92S-XD00E Agitator assy

49 AMC84R-XD00E Agitator unit

50 AMC0BR-XD00E Floor nozzle brush C

51 AMC79R-XD00E Floor nozzle brush B

52 AMC79A-XD00E Body packing

53 AMC03R-XD04E Floor nozzle lower

54 AMC50R-XD00E Floor nozzle roller shaft

55 AMC90Q-XD00E Nozzle roller

56 XWG7+135FY Plain washer

57 XTN3+8BFY Tapping screw

58 AMC68A-XD00E Screw

59 XTN4+18BFY Tapping screw

60 XTN3+16FFJ Tapping screw

61 AMC95S-XD00E Belt unit kit 2belts

62 AMC99W-XD00E Fuse Unit

63 AMC99R-XD00E Mini turbine nozzle MC-E4103

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Aspiradora de Panasonic

Panasonic

Panasonic MC-V6405 Manual de usuario

Panasonic

Panasonic MC-V5737 Manual de usuario

Panasonic

Panasonic MCV7380 - UPRIGHT VACUUM Manual de usuario

Panasonic

Panasonic MC-YL669 Manual de usuario

Panasonic

Panasonic MCV315 - COMMERCIAL VACUUM Manual de usuario

Panasonic

Panasonic MCV7311 - UPRIGHT VACUUMM Manual de usuario

Panasonic

Panasonic mc-ul592 Manual de usuario

Panasonic

Panasonic MC-E851 Manual de usuario

Panasonic

Panasonic MCUG728 Manual de usuario

Panasonic

Panasonic MCCG381 - CANISTER VACUUM - MULTI LANGUAGE Manual de usuario

Panasonic

Panasonic MCV5037 - UPRIGHT VACUUM Manual de usuario

Panasonic

Panasonic MCV7387 - UPRIGHT VACUUM Manual de usuario

Panasonic

Panasonic MC-CG983 Manual de usuario

Panasonic

Panasonic MC-CL779 Manual de usuario

Panasonic

Panasonic MC-UG614 Manual de usuario

Panasonic

Panasonic MC-V5454 Manual de usuario

Panasonic

Panasonic Quickdraw MC-V7531 Manual de usuario

Panasonic

Panasonic MCUG581 - PLATINUM UPRIGHT VAC Manual de usuario

Panasonic

Panasonic MC-CL676 Manual de usuario

Panasonic

Panasonic Quickdraw MC-V7377 Manual de usuario

Panasonic

Panasonic MCV9640 - CANISTER VACUUM CLEA Manual de usuario

Panasonic

Panasonic MC-CL430 Series Manual de usuario

Panasonic

Panasonic Ultra-Pro MC-V400 Manual de usuario

Panasonic

Panasonic MC-4860 Manual de usuario

Manuales populares de Aspiradora de otras marcas

Bissell

Bissell LittleGreen Proheat 1425 Series Manual de usuario

NEFF

NEFF N17XH10 0 Series Manual de usuario

LG A9 Series Manual de usuario

Oreck

Oreck Cordless Captura BK51700 Series Manual de usuario

Kogan

Kogan KAVACROBVWA Manual de usuario

Kränzle

Kränzle VENTOS 50 ID Guía del usuario

EVVO

EVVO Ai35 Manual de usuario

DeWalt

DeWalt DWH200D Manual de usuario

Pontec

Pontec Pondomatic Vacuum Cleaner Manual de usuario

Cleanmaxx

Cleanmaxx PC-P007E Manual de usuario

Exido

Exido 240-114 Manual de usuario

RIDGID

RIDGID WD1685AU0 Manual de usuario

Ezviz

Ezviz RE4P Manual de usuario

STG global

STG global TANVAC HDV3000 Manual de usuario

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Manual de usuario

Factory

Factory M3340 Manual de usuario

Shop-Vac

Shop-Vac VN92 SERIES Manual de usuario

Nobles

Nobles 608669 Manual del producto