Panasonic MC-CL676-ZC79 Manual de usuario

rights reserved. Unauthorized copying and distribu-

tion is a violation of law.

Order No.VCB0707022CE

Vacuum Cleaner

Model No. MC-CL676-ZC79

Product Coior :Sherbet Blue

Destination :Europe

TABLE OF CONTENTS

PAGE PAGE

1 Specifications ----------------------------------------------------- 2

2 Location of Controls and Components ------------------- 3

3 Troubleshooting Guide ----------------------------------------- 5

4 Disassembly and Assembly Instructions ---------------- 6

4.1. Separate the upper and lower bodies. --------------- 6

4.2. P.C.B. assy removal -------------------------------------- 7

4.3. Motor removal ---------------------------------------------- 9

4.4. Cord reel unit replacement-----------------------------10

4.5. Spring-loaded cord reel pre-winding-----------------10

4.6. Installation of some Pakkin----------------------------- 11

4.7. How to disassemble the turbine nozzle-------------11

5 Wiring Connection Diagram ---------------------------------13

6 Exploded View and Replacement Parts List -----------14

6.1. EXPLODED VIEW (ATTACHMENTS) --------------14

6.2. PARTS LIST (ATTACHMENTS) ----------------------15

6.3. EXPLODED VIEW (BODY UNIT) --------------------16

6.4. PARTS LIST (BODY UNIT) ----------------------------17

6.5. PACKING INSTRUCTIONS----------------------------18

6.6. PACKING LIST ------------------------------------------- 19

1 Specifications

Model No. MC-CL676-ZC79

Power source 230V~50Hz

Input power (MAX) 2300W

Input power (Nominal) 2000W

Power control O

Extension wand Telescopic

Floor nozzle -

Turbin nozzle O

Dimensions (WxLxH)mm 290x470x280

Net weight 6.4kg

Cleaning tools Crevice nozzle / Upholstery nozzle

2 Location of Controls and Components

3 Troubleshooting Guide

CONDITION CHECKPOINT METHOD OF INSPECTION CAUSE / REMEDY

Motor fails to rotate Power supply cord Check power supply cord continu-

ity.

If there is no continuity, replace the

cord reel patition unit.

Fuse of P.C.B. Ass’y

(250V, 13A)

Check fuse continuity. If there is no continuity, replace

P.C.B. Ass’y.

Motor continuity Check the conduction between the

terminals of the motor.

If there is no continuity, replace the

motor.

ON/OFF Switch Check continuity across switch

connections

If there is no continuity, replace

P.C.B. Ass’y.

Triac (Inside of P.C.B.) Check if there is any problem in the

triac.

(Please refer to how to check the

triac.)

If it has any problem, replace the

P.C.B. Ass’y.

P.C.B. Ass’y Check the internal parts for any-

thing unusual. (burn-out, melt-

down, etc.)

If anything unusual is found,

replace the P.C.B. Ass’y with new

one.

Motor runs but there is no suction Hose or Suction inlet Check if there is any blockage in

the hose or suction inlet.

If there is any blockage, remove it.

Dust box unit

Upper filter Unit

Secondary filter

Check whether or not the dust box

unit is full of dust or dust is clogged

in the upper filter unit or secondary

filter.

If the dust box unit is full of dust,

then throw away the dust.

If dust is clogged in the upper filter

unit or secondary filter, then throw

away the dust and clean or replace

the upper filter unit or secondary fil-

ter.

Noise or vibration Motor fan Check dust accumulated in motor

fan (it could happen if the vacuum

cleaner has been used without cen-

tral filter).

If there is accumulated dust in the

motor fan, replace the motor and

check filter condition. (never try to

dismantle the motor fan)

Motor does not change power

(runs always at full speed)

P.C.B. Ass’y Examine the triac in the P.C.B.

Ass'y and check whether or not T1

and T2 are short-circuited.

If they are short-circuited, then

replace the P.C.B. Ass'y.

Motor runs irregularly P.C.B. Ass’y Check possible bad contact of

P.C.B. Ass’y.

Replace P.C.B. Ass’y.

4 Disassembly and Assembly Instructions

Important notice: Before replacing any components, make sure to turn OFF the vacuum cleaner.

Remove the power plug from the outlet.

4.1. Separate the upper and lower

bodies.

1. Remove the dust box assy from the main body.

2. Remove the filter cover from the upper body and remove

the filter unit.

3. Remove the three screws fixing the upper and lower bod-

ies.

4. Insert a flat-blade screwdriver into the gap between the

upper body and the ornamental plate unit. Move the

screwdriver in the direction of the arrow to remove the

ornamental plate unit from the three hooks on the upper

body. Remove the ornamental plate unit.

* Unhook the three tabs.

5. Remove the ornamental plate unit from the lower body.

6. Remove the screw fixing the caster unit (on the right in

the figure below) from the bottom of the lower body to

remove the lower caster support plate, caster unit.

7. From the bottom of the lower body, remove the four

screws fixing the upper and lower bodies.

8. Lift the upper body to separate it from the lower body.

4.2. P.C.B. assy removal

1. Remove the control shaft and switch cover unit with

spring A fitted.

2. Wiring treatment

3. Remove the right body packing from the lower body.

4. Remove the P.C.B. assy from the P.C.B. holder.

* When removing the P.C.B. assy, unhook it from the

tab on the P.C.B. holder by spreading the holder

frame.

Note: When removing the P.C.B. assy, do not bend it

to prevent damage and the wires from breaking.

5. Disconnect the fast-on terminal of the lead wire connect-

ing the fan motor unit to the P.C.B. assy.

* When connecting or disconnecting the fast-on ter-

minal, hold the P.C.B. assy and connecting terminals.

6. Disconnect the fast-on terminal of the lead wire connect-

ing the P.C.B. assy to the body partition assy.

4.3. Motor removal

1. Remove the P.C.B. holder from the lower body.

2. Remove the motor set from the lower body.

3. Remove all components fitted to the fan motor unit.

a. Remove the motor support rubber (rear).

b. Remove the motor support.

c. Remove the noise absorber.

d. Remove the motor support rubber (front).

4.4. Cord reel unit replacement

1. Lift the body partition assy (fitted with the cord reel unit)

while removing the cord reel shaft from the side of the

lower body.

2. Remove the screw fixing the body partition assy and the

cord reel unit.

3. Remove the cord reel unit from the body partition assy.

4.5. Spring-loaded cord reel pre-

winding

1. The body partition assy has a spring that pre-winds the

cord reel.

If the cord is not wound, then press the brake lever unit,

and the cord pre-winding will be loosened.

Pre-wind the cord as indicated by the arrow mark.

Number of pre-windings: Four turns

* If you wish to release the pre-winding, then make

sure to hold the cord plug.

Tabla de contenidos

Otros manuales de Aspiradora de Panasonic

Panasonic

Panasonic MC-YL625T147-AE Manual de usuario

Panasonic

Panasonic Ultra-Pro MC-V100 Manual de usuario

Panasonic

Panasonic MC-YL637 Manual de usuario

Panasonic

Panasonic MCV415 - COMMERCIAL VACUUM Manual de usuario

Panasonic

Panasonic MCV5027 - UPRIGHT VACUUM Manual de usuario

Panasonic

Panasonic MC-E3003 Manual de usuario

Panasonic

Panasonic MC-CG973-00 Manual de usuario

Panasonic

Panasonic MC-UL672 Manual de usuario

Panasonic

Panasonic MCUG581 - PLATINUM UPRIGHT VAC Manual de usuario

Panasonic

Panasonic MC-CG461 Manual de usuario

Panasonic

Panasonic MCV7387 - UPRIGHT VACUUM Manual de usuario

Panasonic

Panasonic MC-SB53KH046 Manual de usuario

Panasonic

Panasonic MC-E8031 Manual de usuario

Panasonic

Panasonic MC-CJ917-K747 Manual de usuario

Panasonic

Panasonic MC-UG581-01 Manual de usuario

Panasonic

Panasonic MC-CL609 Manual de usuario

Panasonic

Panasonic MC-CG715K249-AE Manual de usuario

Panasonic

Panasonic MC-YL669 Manual de usuario

Panasonic

Panasonic MC-E761 Manual de usuario

Panasonic

Panasonic MCV9638 - CANISTER VAC.-PLAT Manual de usuario

Panasonic

Panasonic MC-V7358 Manual de usuario

Panasonic

Panasonic MC4850 - CANISTER VACUUM Manual de usuario

Panasonic

Panasonic MC-4860 Manual de usuario

Panasonic

Panasonic MC-CJ915 Manual de usuario

Manuales populares de Aspiradora de otras marcas

Bissell

Bissell LittleGreen Proheat 1425 Series Manual de usuario

NEFF

NEFF N17XH10 0 Series Manual de usuario

LG A9 Series Manual de usuario

Oreck

Oreck Cordless Captura BK51700 Series Manual de usuario

Kogan

Kogan KAVACROBVWA Manual de usuario

Kränzle

Kränzle VENTOS 50 ID Guía del usuario

EVVO

EVVO Ai35 Manual de usuario

DeWalt

DeWalt DWH200D Manual de usuario

Pontec

Pontec Pondomatic Vacuum Cleaner Manual de usuario

Cleanmaxx

Cleanmaxx PC-P007E Manual de usuario

Exido

Exido 240-114 Manual de usuario

RIDGID

RIDGID WD1685AU0 Manual de usuario

Ezviz

Ezviz RE4P Manual de usuario

STG global

STG global TANVAC HDV3000 Manual de usuario

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Manual de usuario

Factory

Factory M3340 Manual de usuario

Shop-Vac

Shop-Vac VN92 SERIES Manual de usuario

Nobles

Nobles 608669 Manual del producto