Panasonic KX-TD612 Manual de usuario
Thank you for purchasing a Panasonic Digital Super Hybrid System, Model KX-TD612.
Before connecting this product, please read this manual carefully and save this manual
for future use.
Model No.
KX-TD612
Digital Super Hybrid System
Getting Started
Version 3
2
Describes the included
accessoriesandrequired
tools for installation.
Shows you how to install
your system.
Describes the basic
programming to make/
receive calls.
Describes how to set the
system programming by
a personal computer
(PC).
Shows the contents of
the CD-ROM.
Preparation
Page 3
Connections
Page 4
Basic
Programming
Page 7
PC Programming
Page 11
Information on
the CD-ROM
Page 16
Contents
3
Check the package contents. The included materials and numbers
included are:
Main Unit ........... 1
Getting Started (This manual) ........... 1
CD-ROM (Including Manuals, etc.) ........... 1
Template (for wall mounting) ........... 1
Necessary user-supplied tools:
Solid wire for the extension connection:
∗The maximum length of the cable may vary depending on the type of the cables.
Solid wire for the CO line connection:
A Serial Interface (RS-232C) Connector for the PC connection.
Cross-head screwdriver and flathead screwdriver.
Electrician’s pliers.
Wall modular jacks to connect the telephone equipment, if required.
AC Cord [PSWAT206E] ........... 1 Screws [PQHE5004Z] and
Washers [XWG35FY] ........... 3
10-pin Terminal Block
[PSJS 0S07Z] ........... 1
(for external equipment)
8-pin Terminal Blocks
[PSJS08S08Z] ........... 3
(for extensions)
Pin Plugs [PQJP E Z]
........... 2
(for paging equipment/
external music source)
Diameter of conductor ø 0.4 mm - ø 0.6 mm
Maximum length of cable: Diameter Maximum length
Single Line Telephone ø 0.5 mm 620 m
Digital Proprietary Telephone ø 0.5 mm 240 m
Diameter of conductor ø 0.4 mm - ø 0.65 mm
Diameter coating ø 0.66 mm - ø 1.05 mm
Before installing your system
Preparation
4
System Connection Diagram
To ISDN (BRI) port 1 and 2 (initial)
To ISDN (BRI) port 3 (additional)
(Lightning Protectors)
3 ISDN (BRI) Lines
12 Extension lines
Door Openers
External Music Source
Amplifier Speaker
Printer or Computer
Single Line Telephone
Cordless Phone
Facsimile
Doorphones
KX-T30865
Panasonic
Car Batteries
Panasonic
Second Ringer Relay
External Relay
: needs optional card.
KX-T7436
KX-T7433
KX-T7431 KX-T7440
German type
Doorphone
Voice Processing System
POWER
VOICEPROCESSING SYSTEM KX-TVP50
1 Analogue CO Line (optional)
Connections
5
Use 8-pin terminal blocks (included) to connect the extension lines. Extension jacks 1 to 4 are available
for eXtra DevicePort (XDP) connection. Extension jacks 5 to 8 are only for digital proprietary telephones.
1. While pressing down on the hole at the top of the terminal block using a small flat type screwdriver,
insert the required telephone wire into the side hole as shown below.
2. Attach the terminal blocks to the extension connectors on the system.
Extension Connection
Push to open
Small flat type
screwdriver
Pull out
to fix
Push in the
Pealed Cable
5 mm - 6 mm
1
Jack no.
2 3 4 5 6 7 8
View of Extension
Connector (Jack 1
–
4)
View of Extension
Connector (Jack 5
–
8)
Jack X-1
Jack
X-2 Jack X
H: High
A: A-wire
B: B-wire
L: Low
H: High
L: Low
To Extensions
(Jack 1
-
4(-1/-2), 5
-
8(-1) )
LH..
LBAH..
•Before making the connection of the Extension Connector to the main unit,
extension lines should be checked carefully.
If the extension lines are connected to the main unit with those wires making a
short circuit between the H-L pins or A-B pins, it may cause a malfunction of
the system, or may damage the circuit of the system in the worst case.
Connections
6
1. Insert the modular plugs of the ISDN (BRI) CO line cords (8-conductor wiring) into the ISDN (BRI)
ports 1 and 2.
2. Connect the line cords to the terminal board or the modular jacks from the Central Office.
CO Line Connection
To Terminal Board or
Modular Jacks from
the Central Office
ISDN (BRI)
Port 1 ISDN (BRI)
Port 2 ISDN (BRI)
Port 3 TA RA RB TB
•When making a point-to-multipoint connection, we recommend you use
connection A above because your system has a terminal register (TR) included.
When making connection B, please consult your dealer to remove the TR in your
system.
Terminal
Equipment 7 Terminal
Equipment 1
To Central Office
Network
Termination
A. When your system is at the end of the connection
Terminal
Equipment 7 Terminal
Equipment 1
To Central Office
Network
Termination
TR
B. When your system is not at the end of the connection
Connections
7
This chapter describes system programming necessary to enable receiving/making an outside call.
Setting Status of Extension: ISDN (BRI) port 1, Jack 1-1 (Extension no. 201)
The following items are required before the programming
Confirm your ISDN telephone number.
Confirm whether your connection type is point-to-point or point-to-multipoint.
Connect a digital proprietary telephone (DPT) with display (e.g. KX-T7436, KX-T7433, etc.) to
the Jack 1-1.
Put the overlay on the DPT connected to Jack 1-1.
Connect the ISDN (BRI) CO line to the ISDN (BRI) port 1.
Before Programming
To Enter the Programming Mode
Dial #.
Press PROGRAM.
You can change the user password.
(Default: 1234) Consult your dealer.
Dial 1234 (user password).
PROGRAM
43
#1 2
Basic Programming
8
[001 System Speed Dialling and Intelligent Call Handling Number Set
[623 CLIP/COLP Number Assignment for Extension
Basic Programming
2. Press NEXT.
SE
NEXTCLRSKP+
SPD & CH Number
3. Dial .
SE
NEXTCLRSKP+
SPD&CH Cod?
1. Dial .
SE
NEXTCLR
SYS-PGM NO?→
SE
NEXTSEL→
500:Not Stored
4. Enter your phone number. 6. Press NEXT.
SE
NEXTSELSKP+
500: 0123456789
7. Repeat steps 4 though 6
until you store all of
your phone number.
SE
NEXTSEL→
500: 0123456789
5. Press .
STORE
8. Press .
0 0 1
1005
END
3. Dial .
SE
NEXTCLRSKP+
Jack NO?
1. Dial .
NEXTCLR
SYS-PGM NO?→
NEXT→
#1-1:5:BI:
SEL+ NEXTSEL→
#1-1:5:AL:
6. Press
→and then enter your
ISDN telephone number.
2. Press NEXT.
NEXTCLRSKP+
CLIP/COLP NO.
NEXTSEL→
#1-1:0:BI:
4. Dial and press
→
.
7. Press .
STORE
5. Keep pressing SEL+ until
AL is displayed.
SE
NEXT
SEL
→
#1-1:5:AL:012345
8. Press .
END
26
5
1
31
1
Basic Programming
9
[423 ISDN Layer 1 Active Mode
[424 ISDN Configuration
3. Dial .1. Dial .
NEXTCLR
SYS-PGM NO?
→
5. Press .
2. Press NEXT.
NEXTCLRSKP+
L1 Active Mode
NEXTCLRSKP+
Port NO?
→
NEXTSEL+
→
#1 :Call
4. Press SEL+ and then
press .
STORE
<If Your Contract is
Point-to-Multipoint>
NEXTSEL+ →
#1 :Permanent
<If Your Contract is
Point-to-Point>
OR
4. Press .
STORE
2 34 1
END
1. Dial .
SE
NEXTCLR
SYS-PGM NO?
→
2. Press NEXT.
SE
NEXTCLRSKP+
Access Mode
SE
NEXTCLRSKP+
Port NO?
→
NEXTSEL+ →
#1 :Multipoint
4. Press SEL+ and then
press .
STORE
<
If Your Contract is
Point-to-Multipoint
>
NEXTSEL+ →
#1 :Point
<
If Your Contract is
Point-to-Point
>
OR
STORE
4. Press .
21
4
1
4
5. Press .
END
3. Dial .
1
1
Basic Programming
10
[425 ISDN Data Link Mode
[426 ISDN TEI Mode
System Restart
After setting the system programming, restart the system. You can restart the system by turning
the Power switch “OFF” and then “ON”.
3. Dial .1. Dial .
NEXTCLR
SYS-PGM NO?
→
5. Press .
2. Press NEXT.
NEXTCLRSKP+
Data Link Mode
SE
NEXTCLRSKP+
Port NO?
→
NEXTSEL+ →
#1 :Call
4. Press SEL+ and then
press .
STORE
<If Your Contract is
Point-to-Multipoint>
NEXTSEL+ →
#1 :Permanent
<If Your Contract is
Point-to-Point>
OR
4. Press .
STORE
2 54
END
1
NEXTCLR
SYS-PGM NO?
→
2. Press NEXT.
NEXTCLRSKP+
TEI Assign
SE
NEXTCLRSKP+
Port NO?
→
NEXTSEL →
#1 :Automatic
<If Your Contract is
Point-to-Multipoint>
NEXTSEL →
#1 :Fix 0
<If Your Contract is
Point-to-Point>
OR
STORE
4. Press . 4. Press and then
press CLR, and then
press .
STORE
SHIFT
1. Dial .
21
6
1
4
5. Press .
END
3. Dial .
1
1
Basic Programming
Otros manuales para KX-TD612
1
Tabla de contenidos
Otros manuales de Sistema telefónico de Panasonic
Panasonic
Panasonic KX-TS105W Manual de usuario
Panasonic
Panasonic KX-TD816E Manual de usuario
Panasonic
Panasonic KXFG2451 - B/W Thermal Transfer Manual de usuario
Panasonic
Panasonic KX-TS105BK Manual de usuario
Panasonic
Panasonic KX-TVA50 Manual
Panasonic
Panasonic KX -T61630 Manual de usuario
Panasonic
Panasonic KX-T2322A Manual de usuario
Panasonic
Panasonic KX-TG5671S Manual de usuario
Panasonic
Panasonic KX-TG5110M - 5.8 GHz DSS Expandable Cordless... Manual de usuario
Panasonic
Panasonic DBS Guía de inicio rápido
Panasonic
Panasonic KX-TD816 Manual de usuario
Panasonic
Panasonic KX-TG7841 Manual de usuario
Panasonic
Panasonic KX-TS500CW Manual de usuario
Panasonic
Panasonic KX-TS105B Manual de usuario
Panasonic
Panasonic Easa-Phone KX-T3185 Manual de usuario
Panasonic
Panasonic KX-TSC11EX Manual de usuario
Panasonic
Panasonic DBS 824 Manual de usuario
Panasonic
Panasonic KX-TD612CE Manual de usuario
Panasonic
Panasonic KX-TS17W Manual de usuario
Panasonic
Panasonic KX-TD816 Manual de usuario
Manuales populares de Sistema telefónico de otras marcas
ASCOM
ASCOM TD 92375GB Manual del propietario
Karel
Karel MS26S Hoja de información del producto
EnGenius
EnGenius DuraFon PRO Manual de usuario
Teledat
Teledat X130 DSL Manual de usuario
SpectraLink
SpectraLink MOG400 Manual de usuario
LG-Nortel
LG-Nortel 300 Series Instrucciones de funcionamiento y seguridad