Panasonic BL-C111A - Network Camera - Pan Guía de inicio rápido

HomeLogic LLC ●

100 Hoods Lane

●

Marblehead, MA 09145

●

Phone (781) 639-5155

●

Fax (781) 639-9677

OneHome™

Management and Control Solutions

Camera Integration Note

Manufacturer: Panasonic

Model Number(s): BL-C111A, BL-C131A (wireless)

Comments: Network Camera (version 3.10)

Document Revision Date: 5/19/2011

NOTE: This document refers to Camera setup in software versions below 5.2 ONLY.

Please see the Rev 5.2 Integration Note for systems running 5.2 or greater.

VERVIEW AND SUPPORTED FEATURES

Installing the Panasonic camera can be broken down into the following steps:

1. Install cameras at desired locations, and pull power and Cat5 cabling as needed. Refer to the

Panasonic documentation for mounting details.

2. Connect the cameras electrically to the home network and configure the cameras. See Camera

Configuration.

3. Integrate the cameras into the OneHome system and test proper operation. This step is outlined

in HomeLogic Configuration Details.

BL-C111A

AND

BL-C131A

SUPPORT THE FOLLOWING FEATURES

Pan / Tilt: These cameras can be turned to see various locations.

Presets: These cameras support presets, allowing the user to store predefined locations such as a

driveway or pool. This feature requires OneHome software version 4.0 or later.

Image Flip: These cameras can be mounted with its base up or down, and the image will appear normal.

Built-in Audio: Audio from the Panasonic cameras built-in microphone is supported in version 4.0 and

later.

Motion Detection: These cameras support motion detection to trigger events in the OneHome system.

BL-C111A

AND

BL-C131A

NOT

SUPPORT THE FOLLOWING FEATURES

Zoom: Cameras lacking optical zoom cannot be zoomed in HomeLogic.

AMERA

ONFIGURATION

The camera configuration is done with software provided by Panasonic, which must be run from a

computer with Windows also connected to the same network as the camera.

The software program from Panasonic is EasyConfig.exe: the version we checked is shown at the top.

MPORTANT

OTES

1. Cameras must be configured one at a time: If you are installing more than one camera, setup

the first one completely before powering up subsequent cameras.

2. Setup the camera within 20 minutes: Initial settings must be made within 20 minutes of the

camera being turned on. If the camera has been powered up for more than 20 minutes, cycle

power to the camera before proceeding.

2 of 11

3. DON’T LOSE THE CAMERA PASSWORD: During setup you will create a user name and

password, which are required to make any other changes in the future. If you lose the user name

or password you will have to factory reset the camera and repeat this entire procedure.

4. DEFAULT USER NAME / PASSWORD: For Panasonic cameras, our default user name is

Administrator and our default password is password.

3 of 11

TARTING THE

ANASONIC

AMERA

OFTWARE

1. Insert the CD from the camera into your PC: It should autostart the Network Camera Setup

software. If it does not, launch Setup.exe from the Panasonic CD.

2. The following Screen appears. Choose Search for Cameras.

3. Wait a moment to allow the software to find the camera: the following screen appears.

4 of 11

4. Select the desired camera, and then click the Access Camera button. After a short delay you will

see a new browser window with the initial password screen below:

5. Type in your desired user name and password and click Save. By default we set the user name to

Administrator and the password to password.

6. After a moment initial setup will complete. When prompted with the screen below, click the “To

Single Camera page” button.

7. You will be prompted to enter your user name and password to login, as shown in the image

below. Type in the user name and password you just set, and click OK.

5 of 11

AMERA

ETTINGS

1. After typing in your user name and password, you will be shown the standard browser interface to

the camera.

2. The system will attempt to install an ActiveX control to show the camera image in the browser

window. This control is not needed for proper OneHome operation, but is needed if you wish to

see the camera image on that computer. If any dialogs appear, close them or accept the ActiveX

control as appropriate for your situation.

3. On Windows computers with popup blocking enabled, you will need to click the appropriate bar to

enable the installation of the ActiveX control.

4. Click Setup at the top to bring up the screen shown below:

6 of 11

5. Click UPnP on the left, then click Disable in the both parts of the screen, as shown below. Click

Save to store your settings.

6. Under Accounts to the left, click Administrator to bring up the screen below. Click Permit

access from guest users, as shown below. Leave the Password boxes blank to prevent

changing your password, then click Save to store your changes. Click OK on any warning

messages.

7 of 11

7. Click on General User under Accounts. Click on General User and the click the Modify button.

8. Click the Level 3 button to automatically check all boxes on the page. Save when finished.

8 of 11

9. Click Network to bring up the network settings screen shown below.

10. Click Static in the Connection Mode to bring up the screen below.

11. Set the IP address to the desired value: we suggest setting the first camera to 192.168.0.80, the

second to 192.168.0.81, and so forth. Check the other settings so they match the screen above,

then click Save to save the settings.

9 of 11

12. If prompted, click to Restart to restart the camera. Note that the camera is now at a different IP

address, so the browser window won’t show the camera.

13. Go to the address line in the browser, and put in the new IP address as shown below:

14. This brings up the camera’s home page shown below:

15. The camera is now at the correct IP address with the correct settings.

16. Close the browser.

10 of 11

OTION

ETECTION FOR

OME

OGIC

DVR

ONFIGURATION

To use Panasonic IP Cameras with the HomeLogic DVR tab, enter the web configuration by typing the

camera IP into the browser and logging on using your username and password. Click Setup, and then

below Buffer/Transfer click Motion Detection. Threshold is the measure of the camera’s sensitivity to

change—a lower setting will cause it pick up smaller changes. Sensitivity affects the light sensitivity—a

higher setting will result in more frequent detections of lighting changes.

Typically, the Threshold should be set to the LOWEST setting and Sensitivity should be set to the

HIGHEST.

Please see the DVR Integration Note for full details on setting up the DVR tab in HomeLogic.

Otros manuales para BL-C111A - Network Camera - Pan

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de Panasonic

Panasonic

Panasonic Super Dynamic II WV-CS854B Manual de usuario

Panasonic

Panasonic GP-US742CUE Manual de usuario

Panasonic

Panasonic WV-NW484S - i-Pro Network Camera Manual de usuario

Panasonic

Panasonic AK-HC1800G Manual de usuario

Panasonic

Panasonic i-Pro WV-SP302 Manual de usuario

Panasonic

Panasonic WVNF302 - NETWORK CAMERA Manual de usuario

Panasonic

Panasonic OneHome KX-HCM110A Manual de usuario

Panasonic

Panasonic WV-CP240 Manual de usuario

Panasonic

Panasonic WVCP160 - COLOR CCTV CAMERA Manual de usuario

Panasonic

Panasonic VL-WD812BX Manual técnico

Panasonic

Panasonic WV-NF284 - i-Pro Network Camera Manual de usuario

Panasonic

Panasonic WV-SFN480PJ Manual de usuario

Panasonic

Panasonic KX-HCM10 Manual de usuario

Panasonic

Panasonic WVNS324 - NETWRK CLR DOME CAME Manual de usuario

Panasonic

Panasonic WV-CF212 Manual de usuario

Panasonic

Panasonic BL-C210 Series Manual de usuario

Panasonic

Panasonic BB-HCM511A Manual de usuario

Panasonic

Panasonic BL-C230A Manual de usuario

Panasonic

Panasonic WV-CP450 Manual de usuario

Panasonic

Panasonic WV-X4571L Manual de funcionamiento

Panasonic

Panasonic WV-TW310L Manual de usuario

Panasonic

Panasonic WV-X4573L Guía de instalación

Panasonic

Panasonic WV-CF624 Manual de usuario

Panasonic

Panasonic WV-SP105 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario