Panasonic TY-SB01F Manual de usuario

Thank you for purchasing this Panasonic product.

■Before using this product, please read these “Operating Instructions” and

the “Operating Instructions” of the projector carefully and save the manuals

for future use.

■Before using this product, be sure to read “Read this rst!” (xpage 3).

DPQX1679ZA/X1

Function Board for 12G-SDI Optical Commercial Use

Operating Instructions

ENGLISH

Model No. TY-SB01FB

ENGLISH

FRANÇAIS

日本語

2 - ENGLISH

Contents

Read this rst! 3

Precautions for use 4

Supported projector 4

Supported SFP module 5

Handling of the product 5

Disposal 6

Accessories 6

Part names and functions 7

Installing the Function Board 8

Before installing or removing the Function Board 8

How to install the Function Board 9

How to remove the Function Board 10

Installing the SFP module 11

How to install the SFP module 11

How to remove the SFP module 12

Connecting example 13

Specications 14

ENGLISH - 3

Read this rst!

WARNING:

Do not spill water on this product or allow this product to get wet.

Doing so may cause electric shock, re, or malfunction due to short circuit

or overheating.

fDo not place a container with liquid close to this product.

fConsult your dealer when liquid such as water is spilled on this

product.

Do not place the supplied port covers and screws in a location that a

child can reach.

Accidentally swallowing them can cause a physical harm.

fSeek a medical advice immediately if a child might have swallowed

them.

Do not disassemble or modify.

Doing so may cause electric shock or re. It may also cause a

malfunction.

CAUTION:

Do not place this product in a location with excessive humidity or

dust, or in a location exposed to oil smoke or steam.

Doing so may cause re or electric shock.

Do not place this product in extremely hot location.

Doing so may deteriorate the part, or may cause re.

fDo not install or store in a location with direct sunlight or close to the

heating device, etc.

Disconnect the power plug from the wall outlet before installing or

removing this product to/from the projector.

Failure to do so may cause electric shock.

The SFP module to be attached to this product is a Class 1 laser product.

Do not look at the SFP module or the connector of the optical ber cable

while the projector is turned on. The laser beam may enter the eyes and

cause damage to the eyes.

Precautions for use

4 - ENGLISH

Precautions for use

This product is a 12G-SDI signal compatible Function Board equipped with

two ports that can install the SFP (Small Form-Factor Pluggable)/SFP+

module (referred to as “SFP module” hereinafter). By installing this product

to the projector manufactured by Panasonic Connect Co., Ltd., long-distance

transmission of the SDI signal via optical ber cable will be possible without

a separate converter to convert from optical signal to electric signal.

Supported projector

This product can be used with following projectors. However, this product

cannot be used if the rmware version of the projector is earlier than the

following compatible rmware version. Use the product after updating the

projector to the latest rmware.

Supported projector Compatible rmware version

PT‑RQ25K, PT‑RQ18K 2.00 or later

PT‑RZ24K, PT‑RZ17K 2.00 or later

PT‑REQ12, PT‑REQ10, PT‑REQ80 2.00 or later

PT‑REZ12, PT‑REZ10, PT‑REZ80 1.00 or later

(As of June 2023)

Note

fThis manual omits the alphabets at the end of projector model numbers.

fThis product may support the projectors that are not described in the table. Conrm

the “Operating Instructions” of the projector. The “Operating Instructions” can be

found on the following URL.

https://panasonic.net/cns/projector/

fThe rmware version can be conrmed in the on-screen menu of the

[PROJECTOR SETUP] menu → [STATUS].

fFor the update procedure of the rmware, access the latest information regarding

the rmware in the PASS website (https://panasonic.net/cns/projector/pass/). It is

necessary to register and login to PASS*1 to access the PASS website.

*1 PASS: Panasonic Professional Display and Projector Technical Support Website

Precautions for use

ENGLISH - 5

Supported SFP module

The 12G-SDI/3G-SDI/HD-SDI compatible optical ber SFP module that is

compliant with MSA (Multi-Source Agreement), and the optical ber SFP

module that the operation has been veried with the projector manufactured

by Panasonic Connect Co., Ltd.

fReceiver (for receiving)

fTransmitter (for sending)

fTransceiver (for sending and receiving)

Note

fThe SFP module is an extension module for converting optical signal to electric

signal or electric signal to optical signal.

fOperation of the sending function is restricted depending on the port where the

SFP module is installed.

fPrepare the commercially available SFP module and the optical ber cable

required for connection according to the usage, video signal to be input,

specication of the external device to be connected, etc.

fThe SFP module that the operation has been veried with the projector

manufactured by Panasonic Connect Co., Ltd. can be conrmed from the following

URL.

https://panasonic.net/cns/projector/

Conrmation of operation for SFP module from other manufacturer has been

performed with the items set independently by Panasonic Connect Co., Ltd.,

and not all the operations are warranted. For operation or performance problems

caused by the SFP module, contact the respective manufacturers.

Handling of the product

rDo not touch the connector section of the Function

Board directly with your hands

The component may be damaged by the static electricity. Before handle this

product, remove the charge in the body by touching the surrounding metal,

etc.

rDo not look into the connector of the SFP module.

The SFP module to be installed on this product is a Class 1 laser product.

Do not look into the SFP module or the connector of the optical ber cable

with the power of the projector turned on. Your eyes may be damaged when

the laser goes into your eyes.

Precautions for use

6 - ENGLISH

Disposal

To dispose of the product, ask your local authorities or dealer for correct

methods of disposal.

Accessories

Make sure that the following accessories are provided with the product.

Numbers enclosed in < > show the number of accessories.

Port cover <2>

(DVHR1128ZA/X1)

(Attached to the product at the time

of purchase)

Screw <2>

(XSB3+8FN)

Attention

fAfter unpacking the product, discard the packaging material properly.

fFor missing accessories, consult your dealer.

fStore small parts in an appropriate manner, and keep them away from small

children.

Note

fSupplied screws are spare parts. Use them when the screws to x the slot cover of

the projector are lost.

fThe model numbers of accessories are subject to change without prior notice.

Precautions for use

ENGLISH - 7

Part names and functions

TY-SB01FB

SIGNAL

SDI OPT

12G/3G/HD

1 IN 2 IN

OUT

1 SFP port 1

This is the port to install the SFP module

for receiving.

2 SFP port 2

This is the port to install the SFP module

for sending and receiving.

3 Input indicator <SIGNAL>

This is the indicator to indicate the

detection state of the video signal. This

is illuminated when input of the video

signal is detected in either or both of the

<SDI OPT 1 IN> terminal and the <SDI

OPT 2 IN> terminal.

Note

fThe sending function of the SFP module for sending or for sending and receiving

will not operate when it is installed in the SFP port 1.

fIn addition to the SFP module for sending and receiving, the SFP module for

receiving or for sending can be installed in the SFP port 2.

rWhen the SFP modules are installed

This is an example when the SFP module for receiving (LC connector) is

installed in the SFP port 1, and the SFP module for sending and receiving

(LC connector) is installed in the SFP port 2.

TY-SB01FB

SIGNAL

SDI OPT

12G/3G/HD

1 IN 2 IN

OUT

1 2

1 <SDI OPT 1 IN> terminal/<SDI OPT 2

IN> terminal

These are terminals to input SDI signal

(optical signal).

2 <SDI OPT OUT> terminal

This is an active through terminal to

output the signal input to the <SDI OPT

1 IN> terminal/<SDI OPT 2 IN> terminal.

Note

fThe input signal to the <SDI OPT 1 IN> terminal or the <SDI OPT 2 IN> terminal

that is selected for input is output from the <SDI OPT OUT> terminal.

Installing the Function Board

8 - ENGLISH

Installing the Function Board

Requesting a qualied technician to install or remove the Function Board

to the projector is recommended. A malfunction may occur due to static

electricity. Consult your dealer.

Before installing or removing the Function Board

fAlways turn off the power of the projector before installing or removing the

Function Board.

gWhen turning off the projector, make sure to follow the procedures

described in the “Operating Instructions” of the projector.

fDo not touch the connector section of the Function Board directly with your

hands.

gThe component may be damaged by the static electricity.

fRemove the static electricity from your body by touching to surrounding

metal, etc., in advance to prevent the static electricity damage.

fTake care not to get injured when installing or removing the Function

Board.

gHands may be injured by the opening of the empty slot of the projector,

the edge of the bracket of the Function Board, socket of the SFP port,

etc.

fWhen installing the Function Board to the slot, insert it into the connector

straight and slowly.

gIt may not operate or cause malfunction if it is not correctly installed.

fThe illustrations in the procedure are examples when installing the

Function Board in PT‑REZ12.

Installing the Function Board

ENGLISH - 9

How to install the Function Board

Screws (two locations)

Slot cover

Guide rail

Fig.1

Fig.2 Fig.3

1) Remove the slot cover. (Fig. 1)

fRemove the two screws xing the slot cover of the projector by

rotating counterclockwise with a Phillips screwdriver. The removed

screws are used to x the Function Board.

fWhen removing the second screw, hold the slot cover with your hand

so it will not fall.

fTo replace from other Function Board, remove the Function Board

following the procedure in “How to remove the Function Board”

(x page 10).

2) Install the Function Board to the projector. (Fig. 2)

fInsert the Function Board along the groove of the guide rail at both

sides inside the slot. Insert the bracket rmly all the way in.

3) Fix the Function Board. (Fig. 3)

fTighten and x with the two screws removed in Step 1).

Attention

fThe removed slot cover is required when the unnecessary Function Board is removed. Store

it so it can be attached in the future.

Installing the Function Board

10 ‑ ENGLISH

How to remove the Function Board

Fig.1

Handles

1) Remove the Function Board. (Fig. 1)

fRemove the two screws xing the Function Board by rotating

counterclockwise with a Phillips screwdriver. The removed screws are

used to x the slot cover.

fHold the handle of the Function Board and remove it slowly.

2) Attach the slot cover.

fAttach the stored slot cover to the empty slot, and tighten and x with

the two screws removed in Step 1).

Attention

fAlways attach the slot cover on the empty slot.

fStore the removed Function Board inside an antistatic bag.

Tabla de contenidos

Otros manuales de Hardware de computadora de Panasonic

Panasonic

Panasonic WZ-TDADP Manual de usuario

Panasonic

Panasonic AJ-PCD35P Manual de usuario

Panasonic

Panasonic CF-BAK0512U Manual de usuario

Panasonic

Panasonic KX-TDA0170 Manual de usuario

Panasonic

Panasonic TY-FB10HD Manual de usuario

Panasonic

Panasonic TY-FB9FDD Manual de usuario

Panasonic

Panasonic 2SA1790J Manual de usuario

Panasonic

Panasonic 2SA2174J Manual de usuario

Panasonic

Panasonic CF-BAW1024AU Manual de usuario

Panasonic

Panasonic MICROCOMPUTER MN103S Manual de instrucciones

Panasonic

Panasonic AV-HS04M4 Manual de usuario

Panasonic

Panasonic MICROCOMPUTER MN103S Instrucciones de instalación y funcionamiento

Panasonic

Panasonic KX-TDE0101 Manual de usuario

Panasonic

Panasonic 2SC2404 Manual de usuario

Panasonic

Panasonic ET-MDN12G10 Manual de usuario

Panasonic

Panasonic 2SA1532G Manual de usuario

Panasonic

Panasonic KX-TVM50 Manual de usuario

Panasonic

Panasonic CF-BAB2048U Manual de usuario

Panasonic

Panasonic UP05C8GG Manual de usuario

Panasonic

Panasonic 2SA2161G Manual de usuario

Panasonic

Panasonic TY-FB10HD Manual de usuario

Panasonic

Panasonic UB-5325 Manual de usuario

Panasonic

Panasonic WJMPU955 - PROCESSING UNIT - TMU Manual de usuario

Panasonic

Panasonic ET-MDNHM10 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

Advantech

Advantech ASMB-935 Series Manual de usuario