Panasonic AJ-YAC77P Manual de usuario
SDTI Interface Board
P
AJ-
F0400T50 @
VQT8801
Check that the following items have been packed together with the board.
Note that as the SDTI board is compatible with both NTSC and PAL, both NTSC and PAL ROMs
have also been included with the board.
CONTENTS PIECES CONTENTS PIECES
SDTI board 1 TRV_IF board (VEP83392B) 1
ROM for NTSC (VSI3385) 1 Coaxial cable (black) 1
ROM for NTSC (VSI3386) 1 Coaxial cable (red) 1
ROM for NTSC (VSI3387) 1 Coaxial cable (yellow) 1
ROM for PAL (VSI3388) 1 SDTI terminal board 1
ROM for PAL (VSI3389) 1 Blank panel 1
ROM for PAL (VSI3390) 1 Installation guide (what you are reading) 1
Introduction
Contents
Connector section
This product is an SDTI interface board designed for use in the AJ-DE77, AJ-DE77H and AJ-
DE77D models using Ver 3.0 or later of the Quick Cutter application.
Installation of this product in the AJ-DE77, AJ-DE77H or AJ-DE77D enables digital data using the
SDTI format*1(digital data compression interface) to be input and output.
1 SDTI dedicated serial digital input connector (BNC x 1)
2 SDTI dedicated serial digital output connector (BNC x 1)
-
2
-
SDTI
IN
OUT
11Used exclusively for SDTI input signals
22Used exclusively for SDTI output signals
*1: SDTI (serial data transport interface) complies with the SMPTE 305M standard.
The data stream format complies with the SMPTE 321M standard.
Introduction .......................................................................................................... 2
Before installation................................................................................................ 2
Connector section................................................................................................ 2
Installation ............................................................................................................ 3
Precautions for SDTI use..................................................................................... 7
Specifications....................................................................................................... 7
CAUTION :
TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER INSTALLATION OF THIS
BOARD TO QUALIFIED SERVICE PERSONNEL.
Before installation
Check that the power of the AJ-DE77, AJ-DE77H or AJ-DE77D (hereafter referred to as the “Quick
Cutter” ) is OFF.
Remove the four screws securing the top panel of the
Quick Cutter, then remove the panel.
Installation
While referring to the figure on the right, first
disassemble the accessory terminal board, and then
use two screws to secure the board to the right side
of the jack panel and two screws to secure the blank
panel on the left side.
(In the case of the AJ-DE77D, the blank panel is not
attached because the SDI terminal board is already in
place on the left side.)
After installation, the panels should appear as shown
in the figure below.
Connect the red coaxial cable provided with the
board to the SDTI terminal board OUT and the black
coaxial cable to the SDTI terminal board IN.
-
3
-
SDI
IN
OUT
AJ-DE77 AJ-DE77D
AJ-DE77H
Jack panel
(AJ-DE77 or AJ-DE77H)
Screws (x6 for
each side panel)
Screws (x7)
Screws (x4)
Blank panel
Remove the 12 screws securing the two side panels
of the Quick Cutter, then remove the panels.
Remove the seven screws securing the jack panel,
then remove the jack panel from the unit.
(It cannot be completely detached because its cable
remains connected.)
Remove the four screws securing the blank panel,
then remove the blank panel from the unit. (Remove
the two screws in the case of the AJ-DE77D.)
Enlarged view
Enlarged view
Before installation
SDI
IN
OUT
SDTI
IN
OUT
SDTI
IN
OUT
AJ-DE77 AJ-DE77D
AJ-DE77H
Blank panel
After installation
After threading the coaxial cables connected to the terminal board
through points 1and 2as shown at right, replace the jack panel
on the main unit.
(AJ-DE77 only)
Remove the two screws and two hexagonal bolts of the AV
interface connector at the bottom rear of the Quick Cutter and
remove the TRV interface board together with its metal clamp.
Installation
(AJ-DE77 only)
Remove the four screws securing the TRV interface board and metal clamp,
and replace the board with the accessory TRV interface board, then use the
four screws to secure the metal clamp.
(AJ-DE77 only)
Use two screws and two bolts to secure the metal clamp, which was
attached to the TRV interface board, to the Quick Cutter unit.
-
4
-
Screws (x2) Hexagonal bolts (x2)
Screws (x2)
Hexagonal bolts (x2)
Screws (x4)
Enlarged view
11Pass the cable through the oval-shaped hole.
22Pull the cable out from the position shown.
AV I/F
1
3
P4
NTSC
1
3
P4
PAL
Black
Red
Yellow
S_IN1
S_OUT2
REF_IN
Jumper setting diagram Coaxial cable connection diagram
After setting NTSC or PAL for the P4 pin of the accessory SDTI board as shown in the jumper setting
diagram, refer to the coaxial cable connection diagram and connect the coaxial cables. The connections
with the board should be made in the following order:
1Connect the coaxial cable (black) which was connected in step 7 to the S_IN1 connector on the SDTI
card provided with the unit.
2 Connect the coaxial cable (red) which was connected in step 7 to the S_OUT2 connector on the SDTI
board.
3 Connect the coaxial cable (yellow) provided with the unit to the REF_IN connector on the SDTI board.
Remove the 20-pin remote cable shown at right
from the Remote I/O board connector followed by
the 3 screws, then remove the board metal clamp
from the Quick Cutter unit.
(For AJ-DE77H and AJ-DE77D, also remove the 2
screws and the fan as shown in the diagram at
right. It is not necessary to remove the fan’s power
cable.)
Installation
Remove the cable and screw shown in the diagram at
right, then remove the X4PCI board from the slot.
Insert the accessory SDTI board into the slot which had
accommodated the X4PCI board, secure it using the
screw, and connect the cable that was disconnected
from the X4PCI board to the connector of the SDTI
board.
Connect one end of the coaxial cable (yellow), which was
connected in step 11, to the J7 connector on the TRV
interface board.
-
5
-
Replace the board metal clamp (and the fan for AJ-DE77H and AJ-DE77D) removed in step 12 and
secure it with the 3 screws.
Connect the 20-pin remote cable removed in step 12 to the Remote I/O board connector.
Yellow
J7
Screws
(x3)
Screw
Enlarged view
Enlarged view
Cable
Screws (x2) for AJ-DE77H or
AJ-DE77D only 20-pin remote cableBoard metal clampFan
Replace the two ROMs (IC2 and IC702) from the VTR units F2 board with the ROMs provided with the
board.
Refer to the figure of the circuit board below to ensure that the ROMs are installed in the correct
direction.
Replace the ROM (IC235) from the VTR unit's F1 board with the ROM provided with the board.
Refer to the figure of the circuit board below to ensure that the ROM is installed in the correct direction.
Remove the 4 screws shown in the diagram at
right and the right metal fitting grip of the
Quick Cutter unit, then remove the F1 and F2
boards of the VTR unit.
Return the F1 and F2 boards removed in step 16 to their original positions, and use the four screws to
secure the right metal fitting grip which was removed in step 16 to the Quick Cutter unit. Secure the side
panels and the top panel using the screws by performing steps 2 and 3 in their reverse order.
-
6
-
Installation
Accessory ROM
VSI3387
VSI3390
Reference
IC235
IC235
NTSC
PAL
Screws (x4)
F1 board
F2 board
IC702 IC2
IC235
Align pin 1, and insert the ROMs
while ensuring that their pins are
not bent in the process.
Align pin 1, and insert the ROM
while ensuring that its pins are
not bent in the process.
Reference
IC2
IC702
IC2
IC702
Accessory ROM
VSI3385
VSI3386
VSI3388
VSI3389
NTSC
PAL
Precautions for SDTI use
Specifications
-
7
-
≥Before handling the interface board and its ROMs, be absolutely sure to attach a grounding strap.
≥Recording operations cannot be performed unless the SDTI input signals are DVCPRO (25
Mbps) format 4x or 1x transfer signals.
≥Recording operations can be performed only when the video, audio and time code data of the
SDTI signals are all regular data in compliance with the DVCPRO (25 Mbps) format.
≥Before use, supply the external reference signal to the reference input connector on the Quick
Cutter unit.
≥When inserting or ejecting a tape from the Quick Cutter equipped VTR, there will be some noise
from the SDTI analog monitor output screen.
≥When using this interface board, be absolutely sure to read the instructions for Quick Cutter
application Ver 3.0 as well.
≥This interface board can be operated with the Quick Cutter Ver 3.0 or later.
However, since it may be necessary to update the version of the software program for the VTR
which contains Quick Cutter, consult your dealer.
GENERAL
Weight Board : 185 g
Terminal board : 32 g
Dimensions Board : 255(W) x 140(H) x 22(D) mm
Terminal board : 28(W) x 88(H) mm
VIDEO/AUDIO IN
Serial digital input : BNC x 1
IN : SDTI input
SDTI : Complies with SMPTE 305M standard
VIDEO/AUDIO OUT
Serial digital output : BNC x 1
OUT : SDTI output
SDTI : Complies with SMPTE 305M standard
PANASONIC BROADCAST & DIGITAL SYSTEMS COMPANY
DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA
Executive Office:
3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500
EASTERN ZONE:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621
Mid-Atlantic/New England:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621
Southeast Region:
1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835
Central Region:
1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200
WESTERN ZONE:
3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500
Dallas Region:
6226 Abington Way, Houston, TX 77008 (713) 802-2726
No. CA/Northwest Region:
5870 Stoneridge, #3, Pleasanton, CA 94588 (925) 416-5108
Government Marketing Department:
52 West Gude Drive, Rockville, MD 20850 (301) 738-3840
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010
Panasonic Sales Company
Division of Matsushita Electric of Puerto Rico Inc.
San Gabriel Industrial Park, 65th Infantry Ave., Km. 9.5, Carolina, Puerto Rico 00630 (787) 750-4300
Tabla de contenidos
Otros manuales de Hardware de computadora de Panasonic
Panasonic
Panasonic 2SA1790G Manual de usuario
Panasonic
Panasonic TY-FB10HMD - Monitor Terminal Expansion... Manual de usuario
Panasonic
Panasonic MICROCOMPUTER MN103S Instrucciones de instalación y funcionamiento
Panasonic
Panasonic 2SA2163 Manual de usuario
Panasonic
Panasonic AJ-YAD455 Manual de usuario
Panasonic
Panasonic ET-MDNFB10 Manual de usuario
Panasonic
Panasonic 2SC3934 Manual de usuario
Panasonic
Panasonic WJ-PB85T08 Manual de usuario
Panasonic
Panasonic CF-BAL1024U Manual de usuario
Panasonic
Panasonic 2SA1790J Manual de usuario
Panasonic
Panasonic KX-TDE0101 Manual de usuario
Panasonic
Panasonic 2SA2021G Manual de usuario
Panasonic
Panasonic 2SA2009G Manual de usuario
Panasonic
Panasonic 2SB0710A Manual de usuario
Panasonic
Panasonic ET-MCYDV100 Manual de usuario
Panasonic
Panasonic AJ-YA931G Manual de usuario
Panasonic
Panasonic CF-BAW1024U Manual de usuario
Panasonic
Panasonic 2SC2404 Manual de usuario
Panasonic
Panasonic 2SB1321A Manual de usuario
Panasonic
Panasonic CF-VEB471 Manual de usuario
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
Hauppauge
Hauppauge WinTV-HVR-2250 Manual de usuario
