Ovislink WL-5420AP Manual de usuario
WL
-
54
20AP
User’s Guide
Table of contents
INTRODUCTION.................................................................................... 1
About the Operation Modes .............................................................................2
LED Indicators...................................................................................................5
Solid.................................................................................................................5
Ports on the Rear Panel.....................................................................................7
GETTING CONNECTED........................................................................ 8
WPA AP -CONFIGURATION VIA WEB ................................................. 9
Login ...................................................................................................................9
Info(Information).............................................................................................10
Assoc(Associations)..........................................................................................11
Wireless (Wireless Configuration) .................................................................12
Visibility Status..............................................................................................12
Access (Access Control)...................................................................................14
Advanced (Advanced Wireless) ......................................................................15
Maximum associated stations........................................................................15
Security .............................................................................................................17
PSK pass-phrase ............................................................................................18
Enable WEP...................................................................................................21
IP Addr (IP Address Settings).........................................................................22
IP Address Mode............................................................................................22
Access point name .........................................................................................22
Admin (Administration)..................................................................................23
Change password. ..........................................................................................23
Reboot/Reset this device................................................................................23
Upgrade system firmware..............................................................................23
BRIDGE -CONFIGURATION VIA WEB ............................................... 25
Login .................................................................................................................25
Info(Information).............................................................................................26
Wireless (Wireless Configuration) .................................................................27
Wireless Mode ...............................................................................................27
Advanced (Advanced Wireless) ......................................................................29
Maximum associated stations........................................................................29
Admin (Administration)..................................................................................31
Device Name .................................................................................................31
Commands: Reboot/Reset this device. ..........................................................32
Upgrade system firmware..............................................................................32
RESET TO THE FACTORY DEFAULTS.............................................. 34
Reset ..................................................................................................................34
Find ...................................................................................................................35
FEDERAL COMMUNICATIONS COMMISSION
INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Any changes or modifications not expressly approved by the grantee of this device could void the
user's authority to operate the equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20cm
between the radiator and your body.
-1-
Introduction
The WL-5420AP is an IEEE802.11g compliant access point, it not only
provides a high transfer rate up to 54Mbps, which is almost five times faster
than the already existing 11Mbps 802.11b products, but is also backward
compatible with the Wireless B equipments.
The WL-5420AP provides 64/128 bit WEP encryption and IEEE802.1x
which ensures a high level of security to protects users’data and privacy.
The MAC Address filter prevents the unauthorized MAC Addresses from
accessing your Wireless LAN. Your network security is therefore double
assured.
This device can support three modes, i.e. Access Point and Bridge.While
acting as a Bridge, this device connects wireless stations for inter-LAN
connection.
Placed anywhere along with an Ethernet LAN, the WL-5420AP allows up to
200 wireless stations within its area of coverage to access transparently to the
corporate network.
The web-based configuration utility allows users to configure via web
browser. Advanced setup and firmware upgrade can be done easily.
-2-
About the Operation Modes
This device provides multiple operational applications with Access Point,
Client, and Bridge (Infrastructure and Ad-hoc) modes, which are mutually
exclusive.
1. Access Point: When acting as an access point, this device connects all
the wireless points (PCs) to a wired network. See the sample application
below.
If you are currently in Bridge mode and want to change to Access Point,
perform the Firmware Upgrade to upload the firmware from the included
CD for Access Point mode. Refer to the section titled “Upgrade system
firmware”for details.
-3-
2. Bridge (Infrastructure): When acting as a Bridge, this device serves as
a wireless client that connects wired stations (refer to the following
illustration) to other access point(s). When becomes a wireless station
(AP1 plus the connected computer 1, 2 and 3) can have the Internet
access if the other Access Point (AP2) has the Internet connection.
If you are currently in Access Point mode and want to change to Bridge,
perform the Firmware Upgrade to upload the firmware from the included
CD for Access Point mode. Refer to the section titled “Upgrade system
firmware”for details.
-4-
3. Bridge (Ad-hoc): When set to the Bridge (Ad-hoc) mode, this device
can only work when connected to a computer, and will work like a
wireless station. You can share files and printers between wireless
stations (PC and laptop with wireless network adapter installed).
The Bridge (Ad-hoc) mode is only for inter-LAN connection and will
not communicate with any wired network.
This device is shipped with configuration that is functional right out of the
box. If you want to change the settings in order to perform more advanced
configuration or even change the mode of operation, you can use the
web-based utility provided by the manufacturer as described in the following
sections.
-5-
LED Indicators
LED Indicators on the Front Panel
StatusLED Indicator
Solid Dim/ Flashing
Power
Glows when power is
applied to this device, the
LED turns solid yellow.
Dim when no power is
applied.
Status Normal Flashing when upgrading
firmware.
LAN-Link Glows when Ethernet is
connected.
Dim when no Ethernet is
connected.
Flashing when this device is
sending/receiving data
LAN-100M Glows for 100Mbps Dim for 10 Mbps Ethernet
-6-
Ethernet connection. connection
LAN-Full Duplex
Glows for Full duplex
mode
Dim for half duplex
WLAN-Link Glows when this device is
associated
Dim when it is not
associated
WLAN-Ready Glows when WLAN is
connected.
Dim when no WLAN is
connected.
Flashing when trying to
connect to WLAN.
WLAN-Active
N/A Flashing when this device is
actively sending/receiving
data over the wireless LAN
connection.
Tabla de contenidos
Otros manuales de Punto de acceso inalámbrico de Ovislink
Ovislink
Ovislink Air Live AirMax4GW Manual de usuario
Ovislink
Ovislink Air Live WL-5470AP Manual de usuario
Ovislink
Ovislink AirLive N.MINI Guía de instalación
Ovislink
Ovislink evo-w54apV2 Manual de usuario
Ovislink
Ovislink AirLive IGR-1500 Manual de usuario
Ovislink
Ovislink AirLive WLA-5000AP Manual de instrucciones
Ovislink
Ovislink Air Live WL-5450AP Manual de usuario
Ovislink
Ovislink AirLive WH-9100MESH Manual de usuario
Ovislink
Ovislink EVO-W54ARv2 Manual de usuario
Ovislink
Ovislink AirLive N.TOP Manual de usuario
