Overland Storage NEO 2000e Manual de usuario

NEO®2000Eand 4000E

Quick Start Guide

The NEO Series®libraries come preconfigured for easy

setup. Follow these steps to install and connect them.

Unpacking

Carefully unpack and verify that you have all the parts:

•NEO 2000Eor NEO 4000Etape library

•Rack rail kit

•NEO Accessory Kit, which includes:

•Power cords and appropriate cables

(depending on the configuration)

•Rack template

•NEO SERIES Documentation & Software CD

•This quick start guide

NOTE: SCSI host cables are not supplied in the NEO2000E

and 4000Eproduct kits. These cables must be purchased

separately.

Figure 1. NEO 2000Eand NEO 4000E

Electrostatic Discharge Information

A discharge of static electricity can damage micro-circuitry

or static-sensitive devices. To help prevent Electrostatic

Discharge (ESD), observe standard ESD precautions.

First Things First—Activate Your Warranty!

Before installing your new unit, it is essential that you

activate your warranty. Technical and warranty support

are not available until this is done:

1. Go to the Overland Technical Support web site at:

http://support.overlandstorage.com/

2. At the MEMBER LOGIN (Figure 2), log in to the site.

NOTE: If you are not yet a member, click the New member?

link and follow the instructions. It’s free and easy!

Figure 2. MEMBER LOGIN Section

3. At the Support Home page menu on the left, select My

Products > Add or Register a Product.

4. Fill in the information and click Submit.

Installing the Tape Library in a Rack

Rail Kit Installation

You must first install the rail kit provided using the

template from the Accessory Kit (see Figure 3).

WARNING: It is recommended that a mechanical lifter

(or at least two people) be used to prevent injury during

rack installation or removal. Also, use care to prevent

tipping of the unit or rack.

CAUTION: Start at the bottom of a rack (or the top of the

last-mounted component) to ensure rack stability.

NOTE: Do not remove the front-door packing materials until

the library is in the rack.

Figure 3. NEO 2000ERack Mounting Template

1. Ensure you have adequate rack space available:

•NEO 2000Erequires 8.75 in. (22.25cm) (5U)

•NEO 4000Erequires 17.5 in. (44.50cm) (10U)

NEO-0153

NEO-0196

(E-Mail) (Password)

FIRST: See other side for instructions

to attach Rack Mount Slides

to tape library unit.

LibraryXpress Neo Series

LXN 2000 Library Module

RETMA RACK MOUNTING TEMPLATE

Start at the bottom of the rack or at

to p of a prev io usly m o unted co mp onen t.

Use a pencil to mark locations for cage

nuts (C) and m ounting brackets (M).

Place the template on the front of the rack.

Match the hole pattern on the template with

th e hole patter n on the vertic al ra ils of the rac k.

On older racks with 10-32 tapped

mounting holes on the vertical rails,

omit four 10-32 cage nuts on the front

and rear slide mounting brackets.

18.89”

6.67"

INSTALLATION TIPS

Use the tickmarks on the vertical rails of the

rack to countt he U-spaces.

Older ra cks do not h ave tic k marks.

Wait until the component is inserted into the rack before

tightening the support rails. The small amount of play

helpsposition the rails to the exact width of the component

being installed.

NOTE:

Ensure Sli d e Out e r Me mber s are l evel fro m

front to rear prior to securing on Rack Frame.

Tick

mar k

2. Using the template (see Figure 4), mark the location of

the mounting hardware on the RETMA rack rails:

Figure 4. Using the NEO Templates

a. Match up the hole pattern indicated on the sides of

the template with the hole pattern in the rack.

b. Use the template to mark the six mounting holes.

c. Remove the template.

3. Repeat Step 2 at the rear using the four bottom holes.

CAUTION: Be sure rear holes are horizontally in line

with the front holes so the unit remains level.

4. Using four screws, loosely attach each pre-assembled

rail set (see Figure 5):

• Threaded-Hole Rack—Position each rail with the

brackets outside the vertical rack member and secure

with the four screws to secure them.

• Non-threaded-Hole Rack—Install the four cage

nuts on the insides of both vertical rack members,

position each rail with the brackets outside the

member, and install the four screws to secure them.

Figure 5. Installing Slide Member Fasteners

5. Tighten the screws on both rear brackets.

6. Slide out the middle slide members until they lock at

the front of the rail assembly.

Library Installation

Use the following instructions to insert your library into a

RETMA rack:

1. Install the two clip nuts on each front rail at the

marked spot (see Figure 6).

Figure 6. Installing The Library Module

2. To reduce weight, we recommend removing the drive

assemblies:

a. Loosen the captive thumbscrews at the top and

bottom of the drive assembly.

b. Fully supporting the assembly, pull the handle to

remove the drive assembly.

c. Place each drive assembly on an ESD surface on its

side as not to bend the tabs.

3. Using a mechanical lift, raise the unit and align the

inner slides on the unit with the rack middle slides.

4. With the middle slide ball bearings at the front detent

position, fully insert the inner slides.

5. Slide the library completely into the rack until the

front panel touches the rack.

6. Remove and discard the tape and packing materials

from the doors, leaving them open.

NEO-9129b

NEO 2000e

NEO 4000e

Mark

Template

Holes

These

NEO-0124

Clip

Nuts

Brackets Outside

NEO-0197

Clip Nut

Middle

Inner

Slide

7. Using the two captive retaining screws, attach the

unit to the rack (Figure 7).

8. If removed, re-insert the power supplies and drives

into the rear of the chassis.

9. Tighten all the front rail screws.

Figure 7. Library Retaining Screws

Cabling Examples

The following shows some common cabling configurations.

IMPORTANT: For more cabling options, refer to the NEO

2000E/4000EUser Guide found on the enclosed

Documentation & Software CD or contact Overland Support.

Management Port Cable Requirement

To meet Class A EMC requirements, a shielded Ethernet

cable must always be used for the management port

connection.

SCSI: Two Drives, Two Hosts

Figure 8 shows a typical SCSI cable configuration for a

library with two tape drives connected to two different bus

adapters or hosts.

Figure 8. Two Tape Drives, Dual Hosts (2000E)

NOTE: To maximize drive performance, it is recommended

that LTO-3, LTO-4, or newer drive types be on separate SCSI

buses.

Fibre Connector: Two Drives on an FC Network

When using Fibre Channel drives on an FC network,

slightly different cabling is required. In this example

(Figure 9), the FC drives connect directly to an FC switch

or Host Bus Adapter (HBA).

Figure 9. FC Drive Library on an FC Network (2000E)

NEO-0200

NEO-0199

Retaining

NEO 2000e

Screws

Retaining

Screws

NEO 4000e

NEO-0193

Terminators

To Host

HBA or Fibre

Switch To Host

SAS: Two Drives, One Host

SAS connections can be part of a multi-wire cable

(Figure 10 and Figure 11) or each on a separate cable to

the host.

Figure 10. Typical SAS Configuration (2000E)Figure 11. NEO 4000Ewith Four SAS Drives

Power Up the Library

1. Connect the supplied power cords to AC receptacles

located on the back of the library module (Figure 12).

2. Toggle the power switches to the ON position (“|”).

3. Touch the GUI touch screen to activate the display

and turn the library module ON.

Figure 12. Powering Up a NEO 4000E

Changing the SCSI ID Number

NEO Series libraries work with the majority of backup

applications without having to make changes to the

default configuration. The tape drives include

preconfigured SCSI IDs, where “Drive n= SCSI ID n.”

Depending on your network configuration, it may be

necessary to change the unit’s SCSI IDs:

1. Press Menu, then under Edit Options, press SCSI/FC.

2. Press the Position n, Drive 1 Bus ID data field.

3. Using the keyboard display, press the new SCSI ID

number (it can be any number from 0 to 15).

The selected number is displayed in the New field.

4. Press Save, and then press OK to confirm.

5. Repeat Steps 1–4 for the other drives.

6. When done, press Back twice to return to the default

screen.

Warranty Information

To view the warranty that comes with this product, visit:

http://www.overlandstorage.com/support/warranty.pdf.

To Host

NEO-0208

NEO-0201

GUI Touch Screen

Power Cords

Power Supply

Switches

Additional Help

You can get additional technical support on the Internet at http://support.overlandstorage.com, or call

1-877-654-3429 (toll-free U.S. & Canada), +44 (0) 118-9898050 (Europe), or +1 (858) 571-5555 Option 5 (International).

Otros manuales para NEO 2000e

Este manual sirve para los siguientes modelos

Otros manuales de Almacenamiento de Overland Storage

Overland Storage

Overland Storage SnapServerXSR 40 Manual de usuario

Overland Storage

Overland Storage NEO 4000e Manual de usuario

Overland Storage

Overland Storage SnapScale X4 Node Guía

Overland Storage

Overland Storage NEO 8000 Manual de usuario

Overland Storage

Overland Storage NEO 8000 Manual de usuario

Overland Storage

Overland Storage ULTAMUS Manual

Overland Storage

Overland Storage NEOs T24 Manual de usuario

Overland Storage

Overland Storage REO 4600 Manual de usuario

Overland Storage

Overland Storage SnapScale X2 Node Manual de usuario

Overland Storage

Overland Storage NEO Series Manual de usuario

Overland Storage

Overland Storage ARCvault 48 Manual de usuario

Overland Storage

Overland Storage NEO 8000 Manual de usuario

Overland Storage

Overland Storage REO Series Manual de usuario

Overland Storage

Overland Storage SnapServer DX1 Manual de usuario

Overland Storage

Overland Storage Snap Server 210 Manual de usuario

Overland Storage

Overland Storage NEO 8000 Manual de usuario

Overland Storage

Overland Storage REO Series Manual de usuario

Overland Storage

Overland Storage SnapServer XSD 40 Manual de usuario

Overland Storage

Overland Storage SnapSAN S5000 Manual de usuario

Overland Storage

Overland Storage SnapServer Manual de usuario

Overland Storage

Overland Storage NEO S-Series Manual de usuario

Overland Storage

Overland Storage SnapServer DX2 Manual de usuario

Overland Storage

Overland Storage NEO 8000 Manual de usuario

Overland Storage

Overland Storage PowerLoader Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario