Overland Storage NEO 8000E Manual de usuario

NEO®8000e

Quick Start Guide

Overview

This document describes how to unpack and install a NEO

8000e enterprise library from Overland Storage.

WARNING: To reduce the risk of electric shock or damage

to equipment, always remove any power cords while

working with the unit.

AVERTISSEMENT: pour réduire le risque de choc

électrique ou endommagement de l'équipement, retirez

toujours les cordons électriques en travaillant avec l'appareil.

CAUTION: While working with the unit, observe standard

Electrostatic Discharge (ESD) precautions to prevent

damage to micro-circuitry or static-sensitive devices.

Before starting, it is essential that you activate your

Overland warranty. Technical and warranty support are not

available until this is done:

1. Go to the Overland Storage web site

(http://www.overlandstorage.com/).

2. Click the

Service & Support

tab.

3. Select

My Products > Register New Product

4. At the Site Login, enter your e-mail address and

password (Figure 1).

NOTE: If you are not yet a member, click “New member?” and

follow the instructions given. It’s free and easy!

Figure 1. Support Site Login

5. Fill in the information and click

Submit

IMPORTANT: Within three business days, you will receive

an e-mail from Overland with your warranty certificate.

Follow the instructions included to complete the process.

Unpack the Library

WARNING: Exercise care when unpacking and moving the

NEO 8000e Library. Due to its size and weight, it is

recommended that at least two people be involved with the

unpacking process.

AVERTISSEMENT: soyez prudent lors du déballage et du

déménagement de la bibliothèque NEO 8000e. En raison

de sa taille et son poids, il est recommandé qu'au moins deux

personnes aident au déballage.

CAUTION: Read and become familiar with this entire

document before starting this unpacking procedure. Steps

performed out of sequence may cause damage to the library

which voids existing warranties.

NOTE: Retain all packaging materials in a protected place in

case the library needs to be shipped to a different location.

These tools are required to unpack and install the library:

•9/16” wrench

•10” adjustable wrench

•Box knife

•#2 Phillips stubby or offset screwdriver

•#2 Phillips screwdriver

•Level, at least 10 inches long (25cm)

Remove the Outer Carton

1. Position the shipping container on a level surface

with adequate clearance to work around it (Figure 2 on

page 2).

NOTE: The container pallet and box is labeled “RAMP SIDE”

on the removal side.

•Allow at least 10 ft. (3.0m) of clearance on the

removal side of the container.

•Allow about 3 ft. (1.0m) of clearance around the other

three sides.

•Allow at least 8 ft. (2.5m) of vertical clearance.

*10400292-001*

NEO 8000e Quick Start Guide Unpack the Library

Figure 2. Unpacking Space Requirements

2. Remove the outside packaging (Figure 3).

a. Cut the shipping straps and remove.

b. Remove the edge boards from the top of the box.

c. Remove the corner boards from the sides of the box.

d. Remove the top cap.

e. Release and remove all of the plastic retainers (on

opposite corners).

f. Remove the two (2) large pieces of cardboard

surrounding the library.

Figure 3. Library Packaging Components (Rear View)

3. Remove the inner packaging (Figure 4).

a. Holding the RAMP and DOOR boxes, remove the two

(2) Top Spacers.

b. Remove the RAMP and DOOR boxes and set them

aside.

c. Remove the plastic bag that covers the library.

Figure 4. Ramp and Door Box Locations

Detach the Pallet

Once the cardboard pieces are removed, you can remove the

hardware that secures the library to the pallet.

1. Remove the ramps from the RAMP box and lay them

down, placing the brackets into the corresponding slots

on the rear of the pallet (Figure 5).

Figure 5. Placing the Ramps in Position

Ramp

Floor

Allow at least 10 ft. in

the rear to remove the

library from the pallet

Allow 3 ft.

around

the library

Allow 8 ft.

vertical

clearance

Plastic

Boards

Corner

Shipping

Retainers

Straps

Top Cap Boards

Edge

RAMP Box

(Library hidden for clarity) Front

Top

DOOR Box

Spacers

(Library hidden for clarity)

Slots

Ramps

NEO 8000e Quick Start Guide Unpack the Library

2. Remove the rear hardware holding the library on the

pallet:

a. To access the hold-down bolts and leveling legs,

remove the rear crosspiece (Figure 6).

Use a #2 Phillips screw driver to remove the

crosspiece screws. Then, lift and slide to remove.

Figure 6. Removing the Rear Crosspiece

b. Using the 9/16” wrench, remove the two bolts and

hold-down brackets.

c. Use a 10” adjustable wrench to raise the two

leveling legs at least to the wheel tops (Figure 7).

Figure 7. Raising the NEO 8000 Leveling Legs

3. Remove the front hardware holding the library on the

pallet:

a. Using a #2 Phillips screw driver, remove the

crosspiece screws.

b. Lifting one end of the crosspiece at a time, use the 9/

16” wrench to remove the bolts and hold-down

brackets securing the library to the pallet.

c. Using care not to allow the library to come off the

pallet, move the library back just far enough to lift

the front crosspiece out.

d. Use the 10” adjustable wrench to loosen and raise the

two leveling legs at least to the wheel tops

(Figure 7).

4. Verify that all four leveling legs can clear the floor at

the bottom of the ramp and that the library is only

supported by the four caster wheels.

WARNING: Most of the weight of a library is located in

the rear. If the leveling legs are not raised high enough,

they can catch at the bottom of the ramps, tipping over the

library.

AVERTISSEMENT: la plupart des poids d'une

bibliothèque est située à l'arrière. Si les pieds de

nivellement ne sont pas élevés assez haut, ils peuvent

prendre au bas de la rampe et faire basculer la bibliothèque.

5. Using two people, carefully move the library down the

ramps and onto the floor.

CAUTION: To prevent damage, do not pull on the media

drawer handles at any time while moving the library.

Attach the Front Doors

Before moving the library to its final operating position,

attach the doors.

CAUTION: The holes used to attach the NEO 8000e front

doors are self-tapping. Care must be exercised during the

attachment of the front library doors. If the screws are

overtightened, the hole may strip. Hand tighten only.

NOTE: The square, straight end of the door is the top and the

curved end is the bottom.

1. Remove the two doors from the DOOR shipping box

and extract them from their plastic shipping bags.

2. Using the supplied Phillips screws, attach the left door

hinges to the frame (Figure 8).

3. Repeat Step 2 for the right door.

Figure 8. Attaching the Door Hinges

Attach the Optional Rear Door

If the optional rear door was purchased with the library,

follow the instructions that came with the door to install it at

this time.

Remove Rear Crosspiece

Bolts and

(Library hidden for clarity)

Brackets

http://support.overlandstorage.com

You can get additional technical support on the Internet at the Overland Storage Support web page, or by contacting Overland Storage using

the information found on the Contact Us page on our web site.

NEO 8000e Quick Start Guide Position and Level the Library

Position and Level the Library

Move the library into its final position and level it:

CAUTION: To prevent damage, do not pull on the media

drawer handles at any time while moving the library.

1. Position the library at its operating location.

2. Run down all four leveling legs by hand until they

contact the floor.

3. Using the 10” adjustable wrench, turn each leveling

leg, one after the other in equal increments, until you

have turned them at least one full turn.

NOTE: Be sure the library has been raised high enough so

none of the casters touch the floor.

4. Place the level, front to rear, on the top side edge of

the library (Figure 9).

5. Note the position of the bubble. Raise both of the front

legs or both of the rear legs the same amount to

achieve a level front-to-rear reading.

6. Place the level across the top front edge of the library.

7. Note the position of the bubble. Raise both of the left

feet or both of the right feet the same amount to

achieve a level side-to-side reading.

8. Recheck the level from front-to-rear and from side-to-

side. Adjust as needed until the library is level.

Figure 9. Positioning the Level

Remove the Drawer Brackets

Once the library is in position, use a #2 Phillips stubby or

offset screwdriver to remove the six drawer shipping

brackets located inside the doors (Figure 10) on the side trim

pieces. Replace the screws back into the trim pieces and

retain the brackets with the shipping carton.

Figure 10. Removing the Drawer Shipping Brackets

Additional Information

Your library is now ready to install and connect the tape

drive assemblies (ordered separately), connect any network

management cables, and power it on.

Follow the instructions that come with the tape drive

assemblies to install them. Additional information and

documentation for the NEO 8000e is available online.

User Guide

For detailed information on configuration and setup of your

library, including expansion and partitioning, refer to the

NEO 8000e User Guide. It is available online at:

http://docs.overlandstorage.com/neo

Warranty and Technical Support

For warranty and technical support information, see our

http://www.overlandstorage.com/company/contact-us/

index.aspx

For information on contacting Overland

Technical Support, see our Contact Support page:

http://docs.overlandstorage.com/support

To search for more service information, visit our

Expert Knowledge Base System:

http://support.overlandstorage.com/kb

If you want to be notified whenever a change is made, click

Watch Category in the Tools box on the upper right on the

Knowledge Base sub-category pages.

Tabla de contenidos

Otros manuales de Almacenamiento de Overland Storage

Overland Storage

Overland Storage NEO Series Manual de usuario

Overland Storage

Overland Storage NEO S-Series Manual de usuario

Overland Storage

Overland Storage REO 1000 Manual de usuario

Overland Storage

Overland Storage ULTAMUS Manual

Overland Storage

Overland Storage NEO 4000e Manual de usuario

Overland Storage

Overland Storage SnapSAN S1000 Manual de usuario

Overland Storage

Overland Storage SnapServer Manual de servicio

Overland Storage

Overland Storage REO 9100 Cómo utilizar

Overland Storage

Overland Storage Snap Server 210 Manual de usuario

Overland Storage

Overland Storage NEO 8000E Manual de usuario

Overland Storage

Overland Storage NEO 2000e Manual de usuario

Overland Storage

Overland Storage REO 4500x Manual de usuario

Overland Storage

Overland Storage NEO 2000e Manual de usuario

Overland Storage

Overland Storage REO 9000 Manual de usuario

Overland Storage

Overland Storage NEO 200S Manual de usuario

Overland Storage

Overland Storage NEO Series Manual de usuario

Overland Storage

Overland Storage SnapServer Manual de usuario

Overland Storage

Overland Storage PowerLoader Manual de usuario

Overland Storage

Overland Storage PowerLoader Manual de usuario

Overland Storage

Overland Storage Neo Series Library Manual de usuario

Overland Storage

Overland Storage NEO 8000 Manual de usuario

Overland Storage

Overland Storage SnapServer DX1 Manual de usuario

Overland Storage

Overland Storage LoaderXpress Guía

Overland Storage

Overland Storage SnapServer DX1 Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario