Overland Storage XchangeNOW ARCvault Series Manual de usuario

This document describes how to remove and replace an

Overland XchangeNOW ARCvault 2U chassis assembly.

WARNING: To reduce the risk of electric shock or

damage to equipment, disconnect the power cord.

CAUTION: A bracket and screws secure the robotics for

shipment and MUST be removed before operating.

IMPORTANT: If possible, document the current settings

by printing out a Full Trace Log before swapping chassis.

Unpacking

Carefully unpack and verify that you have all the parts:

•Spare 2U chassis assembly with drives

•Wire Tie-Down kit

•Magazine Release Tool

•These remove & replace instructions

A Phillips screwdriver is also needed.

Electrostatic Discharge Information

A discharge of static electricity can damage micro-circuitry

or static-sensitive devices. To help prevent Electrostatic

Discharge (ESD), observe standard ESD precautions.

Unpack the spare chassis (Figure 1) and prepare it to receive the magazines and drives from the old unit.

Figure 1. Unpacking the Spare Chassis

WARNING: Due to the weight of the unit, it is

recommended that at least two people be used to lift

the unit out of the box to prevent injury.

1. Open the top of the box (Figure 1) and lift off the top

end caps.

2. Remove the Wire Tie-Down kit.

3. Lift the ARCvault out and set it on a secure surface.

4. Remove the ESD bag.

CAUTION: Do NOT turn the chassis upside down or

allow the front bezel or door to contact the table.

5. Remove the shipping screws underneath (Figure 1):

a. Turn the unit onto its left side making sure the

front bezel does not touch the table.

ARCvault®Series XchangeNOW®

2U Chassis Assembly

Remove & Replace Instructions

Overview & Notes

ARC-0011

Unpack Spare Chassis

ARC-0171

End Cap

Spare Chassis

ESD Bag

Carton

Tie-Down Kit

ARC-0048

Front Bezel

Off Table Screws & Well-Nuts

Must Be Removed

Shuttle Bracket Hole

Screw

Well-Nut

Pull

b. Unscrew each shipping screw about one-half inch

leaving the screws in the well-nuts.

c. Using the finger pulls, remove and retain the well-

nuts and screws.

d. Carefully return the library to its normal, upright

operating position.

6. Opening the left door, remove and retain the screw

holding the shuttle bracket in place (Figure 2).

Figure 2. Remove the Bracket Screw (Top Inside View)

7. Remove the shuttle bracket (Figure 3):

a. Slightly lift the bracket up to clear the shuttle.

b. Swing the rear of the bracket to the left aligning it

with the magazine bay.

c. Pull the bracket straight out and retain.

Figure 3. Remove the Shuttle Bracket

8. Close the door.

9. At the rear, remove the AC receptacle label (Figure 4).

Figure 4. Removing the AC Receptacle Label

10.Place the packaging components in the box, including

the bracket, and set aside for returning the old unit.

To replace a chassis, you must first remove the media

magazines (Figure 5).

NOTE: ARCvault 12 model only has one magazine located on

the right side.

Figure 5. ARCvault Magazines to be Removed

CAUTION: Keep a loaded magazine level. Don’t hold

magazine by the handle; use both hands to support it.

Remove Magazines with Power On

1. At the OCP Default screen, press Media > Mag

Access > OK (at the offline message) > Unlock All.

2. Open the right door and remove the right magazine.

3. For an ARCvault 24, open the left door and remove the

left magazine.

Continue with “Remove Unit from Rack.”

Remove Magazines with Power Off

Should there be a loss of power, you can still access the

magazines in models built after November 2006 by using

the Magazine Release Tool (MRT) or a 1mm (0.040 in.)

diameter wire at least 5cm (2 in.) long.

1. Open the magazine door (Figure 6).

Figure 6. Manually Releasing a Magazine

2. Slide the MRT into the slot under the handle.

Remove This Screw

Shuttle

Bracket

Front Bezel

Well-Nut

Left Door

Opening

Hole

cBracket Front Lip

ARC-0027

Remove Magazines From Old Unit

ARCvault 24 (both)

ARCvault 12

(right only)

Insert

Media Magazine

Door

Tool Here

Magazine

Release Tool

3. While pressing firmly with the tool, pull the magazine

out about one inch (2.5cm).

4. Remove the tool.

5. Slide the magazine all the way out.

6. For an ARCvault 24 left magazine, repeat Steps 1–5.

Remove Unit from Rack

WARNING: It is recommended that a mechanical lifter

(or at least two people) be used to prevent injury during

rack removal and reinsertion.

1. If necessary, at the OCP, press Power > Power Off

Library > OK (at the power down message).

2. After the unit has shut down, at the rear, remove the

power cord and all cables.

3. At the front, open the doors and loosen the retaining

screws inside (Figure 7).

4. Carefully remove the ARCvault unit from the rack

and place it on a secure, flat surface.

NOTE:

Some units require a tool to release the rail stops.

Figure 7. Left Retaining Screw

Install New Unit in Rack

1. Swap out the chassis assemblies.

2. Carefully slide the new ARCvault into the rack rails.

3. At the front, open the doors and tighten the retaining

screws to the rack.

4. Reinsert the media magazines and close the doors.

NOTE:

If the old unit was an ARCvault 12, insert the single

magazine into the right-side leaving the left side empty.

5. At the rear of the unit, reconnect the LVD SCSI cable,

SCSI terminator, and any management cables.

6. Plug in the power cord and power on the unit.

Configure the Unit

1. If the old unit was an ARCvault 12, reconfigure the new

unit (Figure 8) to also be a 12-slot autoloader:

a. Log into the RMU as Administrator (password = 2)

using IP address 10.0.0.1.

b. Go to Setup > Library.

c. Set Number of Enabled Slots = 12.

d. Click Functions > Reboot Library.

2. Log into RMU > Setup and make any changes to

configure the new unit like the old one.

Use the Trace Log from the old unit to obtain the

configuration data.

Figure 8. RMU Setup Library Option

Left

Retaining Screw

Incorporate New Chassis

IMPORTANT: If the old unit didn’t power down with the shuttle

parked, contact Overland Technical Support.

Secure the Robotics

CAUTION: Units that do not have the four holes

underneath for the well-nuts and screws must use the

enclosed Wire Tie-Down kit to secure the robotics before

packaging the unit. Follow the instructions that come

with the kit and then continue with the section “Repack

the Chassis.”

For units with the four holes in the chassis bottom and

track plate, follow this procedure:

1. Open the left door.

2. Install the shuttle bracket:

a. Holding the shuttle bracket by the front lip

(Figure 3), slide it into the magazine bay.

b. Swing the rear of the bracket to the right until it

contacts the shuttle.

c. Press the front lip of the bracket down and to the

right until the screw holes align (Figure 2).

You should hear a click as the bracket slips into

place over the shuttle.

d. Install the screw that holds the shuttle bracket to

the bottom edge of the front panel.

3. Turn the unit onto its left side with the front bezel

off the table.

4. Install the shuttle bracket well-nut:

a. While pressing the shuttle bracket down, visually

check the hole alignment from underneath.

All three holes should be visible and aligned.

b. Insert a well-nut and screw through the three

holes using the extended screw as a handle.

c. While continuing to hold the bracket against the

shuttle, turn the screw three (3) full turns into

the well-nut (Figure 9).

Figure 9. Well-Nut Insertion (Side View)

5. Insert the remaining three well-nuts using the

extended screws, and tighten each one three turns.

6. Carefully return the library to the upright position.

Repack the Chassis

Once the robotics are secure, repack the unit for shipment.

1. Open the top of the box and remove all the packaging

materials stored there except the two bottom end caps.

2. With the ARCvault on a secure surface, slide it into the

ESD bag and seal with packing tape.

3. Using two people, lower the packaged ARCvault into

the box.

4. Place the two top end caps onto the unit.

5. Tape the box using the type of tape required by the

shipper for the shipping method being used.

Return Old Chassis

Well-Nut

Bracket

Track

Chassis

Correct Incorrect

Shuttle

Stop Washer

Plate

Additional Help

You can get additional technical support on the Internet at http://support.overlandstorage.com, or call

1-877-654-3429 (toll-free U.S. & Canada), +44 (0) 118-9898050 (Europe), or +1 (858) 571-5555 Option 5 (International).

Otros manuales de Almacenamiento de Overland Storage

Overland Storage

Overland Storage NEO XL Series Manual de usuario

Overland Storage

Overland Storage NEO 8000 Manual de usuario

Overland Storage

Overland Storage NEO XL Series Manual de usuario

Overland Storage

Overland Storage NEO 2000e Manual de usuario

Overland Storage

Overland Storage NEOs T24 Manual de usuario

Overland Storage

Overland Storage SnapScale X2 Node Manual de usuario

Overland Storage

Overland Storage NEO S-Series Manual de usuario

Overland Storage

Overland Storage NEO 2000e Manual de lista de piezas

Overland Storage

Overland Storage NEO 8000E Manual de usuario

Overland Storage

Overland Storage NEO 2000e Manual de usuario

Overland Storage

Overland Storage NEO 8000E Manual de usuario

Overland Storage

Overland Storage NEO 8000E Manual de usuario

Overland Storage

Overland Storage NEO XL Series Manual

Overland Storage

Overland Storage REO 4500x Manual de usuario

Overland Storage

Overland Storage NEO 8000 Manual de usuario

Overland Storage

Overland Storage NEO 8000 Guía

Overland Storage

Overland Storage SnapSAN S3000 Manual de usuario

Overland Storage

Overland Storage ARCvault 2U Series Manual de usuario

Overland Storage

Overland Storage ARCvault 12 Manual de usuario

Overland Storage

Overland Storage REO 1000 Manual de usuario

Overland Storage

Overland Storage SnapServer DX1 Manual de usuario

Overland Storage

Overland Storage Neo Series Library Manual de usuario

Overland Storage

Overland Storage PowerLoader Manual de usuario

Overland Storage

Overland Storage NEO Series Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario