Oventrop REGTRONIC PM Manual de usuario

INSTRUCTIONS FOR

INSTALLERS

Oventrop

REGTRONIC PM

Important!

Please read the instructions carefully before installing and operating the unit!

Failure to do this can void product warranty!

Please keep the instructions in a safe place!

This unit described has been manufactured and inspected according to CE

regulations.

Instructions for installers REGTRONIC PM

Instructions for installers 136955080 2 1317ZB010-10B-E, Revised 03/2008

REGTRONIC PM

Parameters set using the System Settings menu should only be

configured or modified by installers or qualified technical personnel.

Setting the wrong parameters can compromise the functionality of the

control unit and solar power system

Table of Contents:

"SYSTEM SETTINGS" MENU/ CHANGES TO THE SYSTEM..................................................... 3

USING A DATASTICK

................................................................................................................. 4

2.1

ACTORY SETTINGS

.................................................................................................................. 4

2.1.1

Restoring factory settings.................................................................................................. 4

2.1.2

Saving/loading configuration parameters.......................................................................... 4

2.2

PDATING SYSTEM SOFTWARE

.................................................................................................. 4

Instructions for installers REGTRONIC PM

Instructions for installers 136955080 3 1317ZB010-10B-E, Revised 03/2008

REGTRONIC PM

1 "S

YSTEM

ETTINGS

HANGES

TO THE SYSTEM

During normal operation, the "System

Settings" menu only displays parameters

and does not allow them to be altered.

This prevents accidental changes. To

change parameters, this menu must be

selected within one minute of switching

on the unit.

While the system is running, changes can

be made using the System Settings menu

by pressing the top , bottom

and right-hand button

simultaneously.

Once the user is in the menu, no time

limits apply.

The System Settings menu "locks"

itself automatically one minute after the

unit has been switched on and one

minute after the user has exited the

menu.

The System Settings menu is used to

select the basic schema and the language,

and also to activate or deactivate the

available protective and ancillary features.

The buttons and are used

to page through the various submenus.

The status – e.g. "On" or "Off" – is also

shown next to the name of each submenu.

Submenus are selected by using the

button.

Allocation of layout no. to system number: M1013 = 3310, M1016 = 3311, M1020 = 3312,

M1021=3313, M1022=3314, M1023=3315, M1024=3316, M1026=3317, M1027=3318,

M1028=3319, M1032=3320, X1010=3301, X1020=3302, X1030=3303.

Note: 3300 is the initial software set!

Example: Change system from 3300to 3310

System sel.

[off]

off

System

3300

off ok

3300 3301 ok

Service

[off]

MultiReg3

[off]

Instructions for installers REGTRONIC PM

Instructions for installers 136955080 4 1317ZB010-10B-E, Revised 03/2008

REGTRONIC PM

2 U

SING A

ATA

TICK

An installer or technician can use a DataStick

for the following tasks:

Updating unit parameters

Saving/loading factory settings

Updating system software

2.1 Factory settings

Factory settings can be saved, loaded or

restored in the "System Settings" menu. This also makes it possible to transfer

configuration data from one control unit to

another, for example.

2.1.1 Restoring factory settings

Menu item "Factory settings":

•Off

•On: Restores the default factory settings

2.1.2 Saving/loading configuration parameters

Menu item "Factory settings". Parameters:

Only insert or remove the DataStick

at this menu. If the DataStick

has been previously

used as a programming stick, then other menus in the system will ask the user if the software

on the DataStick

should be loaded! Parameter backups on the stick will not have this effect.

•Off

•Save

•Stick available: Message "OK"

-Stick unavailable: Message "OK" (the data will be sent, although it cannot be

stored)

•Load

-Stick available, system no. and system version on the stick match the data in

the control unit: Message "OK"

-Stick available, system no. on the stick matches the data in the control unit,

but the version is different: Message "Chk. par."

: the installer needs to check and verify the parameters.

-System no. does not match the system no. in the control unit: Message "Error"

2.2 Updating system software

First, insert the DataStick. If the DataStick

contains a software package that is valid

for this unit, then the screen will display

"Copy DataStick start?". Press the "OK"

button twice to confirm, and the copy

process will start. Once copying has

finished, the unit will ask you to remove

the DataStick. The control unit will then

reboot.

Otros manuales de Controladores de oventrop

oventrop

oventrop Aktor M ST L Modbus Manual de usuario

oventrop

oventrop REGTRONIC PC Manual de usuario

oventrop

oventrop 1158021 Manual de usuario

oventrop

oventrop Regtronic RD-W Manual de usuario

oventrop

oventrop Regtronic RX Manual de usuario

oventrop

oventrop Aktor T ST 1012953 Manual

oventrop

oventrop REGTRONIC PX Instrucciones de uso

oventrop

oventrop Aktor M Manual

oventrop

oventrop ENOCEAN R-Tronic RT B Manual de usuario

oventrop

oventrop Hydromat DFC Instrucciones de funcionamiento

oventrop

oventrop Aktor M ST L Manual de usuario

oventrop

oventrop Unibox E RTL Manual de usuario

oventrop

oventrop Aktor M ST L Manual de usuario

oventrop

oventrop Regumaq K Manual de usuario

oventrop

oventrop Hydromat DP DN 25 Manual

oventrop

oventrop Regtronic KM IP Manual de usuario

oventrop

oventrop DN 15 Manual de usuario

oventrop

oventrop Hycocon DTZ Manual de usuario

oventrop

oventrop Regtronic RH HT Instrucciones de funcionamiento

oventrop

oventrop Regtronic RM Instrucciones de funcionamiento

oventrop

oventrop Hydromat DTR Manual de usuario

oventrop

oventrop Hydromat DTR Series Manual de usuario

oventrop

oventrop R-Tronic Manual de usuario

oventrop

oventrop OV-5 Manual del propietario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario

oventrop REGTRONIC PM Manual de usuario

Manuales populares de Controladores de otras marcas